1. Ashby MF, Bréchet YJM. Designing hybrid materials. Acta Materialia. 2003;51(19):5801-5821. [
Link] [
DOI:10.1016/S1359-6454(03)00441-5]
2. Ashby MF, Bréchet YJM, Cebon D, Salvo L. Selection strategies for materials and processes. Materials & Design. 2004;25(1):51-67. [
Link] [
DOI:10.1016/S0261-3069(03)00159-6]
3. Han SH. Influence of diffusion coefficient on chloride ion penetration of concrete structure. Construction and Building Materials. 2007;21(2):370-378. [
Link] [
DOI:10.1016/j.conbuildmat.2005.08.011]
4. Gedge G. Structural uses of stainless steel — buildings and civil engineering. Journal of Constructional Steel Research. 2008;64(11):1194-1198. [
Link] [
DOI:10.1016/j.jcsr.2008.05.006]
5. Kim IK, Hong SI. Effect of heat treatment on the bending behavior of tri-layered Cu/Al/Cu composite plates. Materials & Design. 2013;47:590-598. [
Link] [
DOI:10.1016/j.matdes.2012.12.070]
6. Dhib Z, Guermazi N, Ktari A, Gasperini M, Haddar N. Mechanical bonding properties and interfacial morphologies of austenitic stainless steel clad plates. Materials Science and Engineering A. 2017;696:374-386. [
Link] [
DOI:10.1016/j.msea.2017.04.080]
7. Manikandan P, Hokamoto K, Deribas AA, Raghukandan K, Tomoshige R. Explosive welding of titanium/stainless steel by controlling energetic conditions. Materials Transactions. 2006;47(8):2049-2055. [
Link] [
DOI:10.2320/matertrans.47.2049]
8. Pérez-Quiroz JT, Terán J, Herrera MJ, Martínez M, Genescá J. Assessment of stainless steel reinforcement for concrete structures rehabilitation. Journal of Constructional Steel Research. 2008;64(11):1317-1324. [
Link] [
DOI:10.1016/j.jcsr.2008.07.024]
9. Hosseini M, Danesh Manesh H. Bond strength optimization of Ti/Cu/Ti clad composites produced by roll-bonding. Materials & Design. 2015;81:122-132. [
Link] [
DOI:10.1016/j.matdes.2015.05.010]
10. Jang J, Sung M, Han S, Yu WR. Prediction of delamination of steel-polymer composites using cohesive zone model and peeling tests. Composite Structures. 2017;160:118-127. [
Link] [
DOI:10.1016/j.compstruct.2016.10.025]
11. Soltanali Nejad M, Haerian Ardakani A. Investigation of joint quality of aluminium-1350 ans Stw22 steel strips by warm rolling. 11st Congress of Iranian Metallurgical Engineering Society, Isfahan. Isfahan: Esfahan Steel Company; 2007. [Persian] [
Link]
12. Danesh Manesh H, Shahabi HS. Effective parameters on bonding strength of roll bonded Al/St/Al multilayer strips. Journal of Alloys and Compounds. 2009;476(1-2):292-299. [
Link] [
DOI:10.1016/j.jallcom.2008.08.081]
13. Sapanathan T, Ibrahim R, Khoddam S, Zahiri SH. Shear blanking test of a mechanically bonded aluminum/copper composite using experimental and numerical methods. Materials Science and Engineering A. 2015;623:153-164. [
Link] [
DOI:10.1016/j.msea.2014.11.045]
14. ASM International, editor. Atlas of stress-strain curves. Russell Township: ASM International; 2002. pp. 67-92. [
Link]
15. Rasmussen KJR. Full-range stress-strain curves for stainless steel alloys. Journal of Constructional Steel Research. 2003;59(1):47-61. [
Link] [
DOI:10.1016/S0143-974X(02)00018-4]
16. Kocich R, Macháčková A, Kunčická L, Fojtík F. Fabrication and characterization of cold-swaged multilayered Al-Cu clad composites. Materials & Design. 2015;71:36-47. [
Link] [
DOI:10.1016/j.matdes.2015.01.008]
17. Alfano G, Crisfield MA. Finite element interface models for the delamination analysis of laminated composites: Mechanical and computational issues. International Journal for Numerical Methods in Engineering. 2001;50(7):1701-1736. [
Link] [
DOI:10.1002/nme.93]
18. ANSYS. ANSYS documentation [Internet]. Ontario: Sharcnet; 2017 [Cited 2018 March 15]. Available From: https://www.sharcnet.ca/Software/Ansys/17.0/en-us/help/ans_thry/thy_mat11.html [
Link]