Volume 19, Issue 12 (December 2019)
Modares Mechanical Engineering 2019, 19(12): 2979-2986 |
Back to browse issues page
Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
Aghaei M, Nazari F, Honarpisheh M. Effect of Cooling System on the Mechanical Properties and Residual Stress of Steel AISI 1045 in Quenching Heat Treatment . Modares Mechanical Engineering 2019; 19 (12) :2979-2986
URL: http://mme.modares.ac.ir/article-15-28270-en.html
URL: http://mme.modares.ac.ir/article-15-28270-en.html
1- Manufacturing Department, Mechanical Engineering Faculty, University of Kashan, Kashan, Iran
2- Manufacturing Department, Mechanical Engineering Faculty, University of Kashan, Kashan, Iran , honarpishe@kashanu.ac.ir
2- Manufacturing Department, Mechanical Engineering Faculty, University of Kashan, Kashan, Iran , honarpishe@kashanu.ac.ir
Abstract: (4894 Views)
Quenching heat treatment is one of the most used processes in the industry, which has a great influence on the properties of materials. Accurate understanding of the effects of this process on the behavior of materials can be effective in better use of this process. In this research, the effect of quenching media on the mechanical behavior of wide used steel of AISI 1045 has been investigated and the residual stress created in the structure has been studied using the contour method. In this regard, three cooling environments of water, oil, and molten salt have been utilized, and after examining the strength and contour of hardness resulted by each cooling environment, the residual stresses have been investigated by the contour method. Also, the uncertainty of residual stresses in the environment with the most influencing factor has been evaluated. Investigation of the results shows that quenching in water can create higher hardness and strength, and more excessive compressive residual stress with greater penetration depth than the other environments. But cooling media of water creates more heterogeneous of the structure between the surface and the center of the piece, while quenching in a molten salt environment, with maintaining a structural homogeneity close to the annealing state, can increase the hardness and strength, and generate compressive residual stresses with a penetration depth of about 1.3 mm. Investigation of uncertainty for quenching in the water environment showed that the greatest error in the residual stresses was about 9%, and the error resulting from data smoothing had the most effect on the measurement of residual stresses by the cantor method.
Keywords: Quenching Heat Treatment, Mechanical Properties, Residual Stress, Structural Homogeneity, Uncertainty, Steel AISI 1045
Article Type: Original Research |
Subject:
Analysis & Selection of Materials
Received: 2018/12/17 | Accepted: 2019/05/26 | Published: 2019/12/21
Received: 2018/12/17 | Accepted: 2019/05/26 | Published: 2019/12/21
References
1. Shariati M, Mehrabi H. An investigation of the fatigue of CK45 steel in the as-received state and after pre-fatigue deformation. Fatigue & Fracture of Engineering Materials & Structures. 2015;38(4):489-502. [Link] [DOI:10.1111/ffe.12249]
2. Yazdania S, Yoozbashi N, Ebrahimi A. Enhancement of fatigue strength of SAE 1045 steel by tempering treatment and shot peening. Materials Science Forum. 2007;561-565:41-44. [Link] [DOI:10.4028/www.scientific.net/MSF.561-565.41]
3. Şimşir C, Gur CH. 3D FEM simulation of steel quenching and investigation of the effect of asymmetric geometry on residual stress distribution. Journal of Materials Processing Technology. 2008;207(1-3):211-221. [Link] [DOI:10.1016/j.jmatprotec.2007.12.074]
4. Prime MB, Newborn MA, Balog JA. Quenching and cold-work residual stresses in aluminum hand forgings: contour method measurement and FEM prediction. Materials Science Forum. 2003;426-432:435-440. [Link] [DOI:10.4028/www.scientific.net/MSF.426-432.435]
5. Kartal ME. Analytical solutions for determining residual stresses in two-dimensional domains using the contour method. Proceedings. Mathematical, Physical, and Engineering Sciences. 2013;469(2159):1-20. [Link] [DOI:10.1098/rspa.2013.0367]
6. Mahmoodi M, Sedighi M, Tanner DA. Experimental study of process parameters' effect on surface residual stress magnitudes in equal channel angular rolled aluminium alloys. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 2014;228(12):1592-1598. [Link] [DOI:10.1177/0954405414522449]
7. Hossain S, Daymond MR, Truman CE, Smith DJ. Prediction and measurement of residual stresses in quenched stainless-steel spheres. Materials Science and Engineering A. 2004;373(1-2):339-349. [Link] [DOI:10.1016/j.msea.2004.02.014]
8. Mahmoudi AH, Hossain S, Truman CE, Smith DJ, Pavier MJ. A new procedure to measure near yield residual stresses using the deep hole drilling technique. Experimental Mechanics. 2009;49(4):595-604. [Link] [DOI:10.1007/s11340-008-9164-y]
9. Gorkunova ES, Zadvorkin SM, Gorulevac LS. Specific features of the determination of residual stresses in materials by diffraction techniques. AIP Conference Proceedings. 2017;1915(1):030006. [Link] [DOI:10.1063/1.5017326]
10. Jeanmart P, Bouvaist J. Finite element calculation and measurement of thermal stresses in quenched plates of high-strength 7075 aluminium alloy. Materials Science and Technology. 1985;1(10):765-769. [Link] [DOI:10.1179/mst.1985.1.10.765]
11. Kotobi M, Honarpisheh M. Through-depth residual stress measurement of laser bent steel-titanium bimetal sheets. The Journal of Strain Analysis for Engineering Design. 2018;53(3):130-140. [Link] [DOI:10.1177/0309324717753212]
12. Kotobi M, Honarpisheh M. Experimental and numerical investigation of through-thickness residual stress of laser-bent Ti samples. The Journal of Strain Analysis for Engineering Design. 2017;52(6):347-355. [Link] [DOI:10.1177/0309324717719212]
13. Nervi S, Szabo BA. On the estimation of residual stresses by the crack compliance method. Computer Methods in Applied Mechanics and Engineering. 2007;196(37-40):3577-3584. [Link] [DOI:10.1016/j.cma.2006.10.037]
14. Robinson JS, Hossain S, Truman CE, Paradowska AM, Hughes DJ, Wimpory RC, Fox ME. Residual stress in 7449 aluminum alloy forgings. Materials Science and Engineering A. 2010;527(10-11):2603-2612. [Link] [DOI:10.1016/j.msea.2009.12.022]
15. Albertini G, Caglioti G, Fiori F, Pirling T, Stanic V, Wright J. Neutron diffraction measurement of residual stresses in AA6082 quenched samples. Materials Science Forum. 2000;347-349:598-602. [Link] [DOI:10.4028/www.scientific.net/MSF.347-349.598]
16. Amini S, Masoudi S, Amirian G. Effect of machining and quench-induced residual stress on the distortion of thin-walled parts. Modares Mechanical Engineering. 2016;15(12):357-366. [Persian] [Link]
17. Prime MB. Cross-sectional mapping of residual stresses by measuring the surface after a cut. Journal of Engineering Materials and Technology. 2001;123(2):161-168. [Link] [DOI:10.1115/1.1345526]
18. Honarpisheh M, Nazari F. Uncertainty analysis of contour method in the hot extruded Aluminum specimens. Modares Mechanical Engineering. 2017;17(5):439-445. [Persian] [Link]
19. Kartal ME, Turski M, Johnson G, Fitzpatrick ME, Gungor S, Withers PJ, Edwards L. Residual stress measurements in single and multi-pass groove weld specimens using neutron diffraction and the contour method. Materials Science Forum. 2006;524-525:671-676. [Link] [DOI:10.4028/www.scientific.net/MSF.524-525.671]
20. Alinaghian I, Honarpisheh M, Amini S. The influence of bending mode ultrasonic-assisted friction stir welding of Al-6061-T6 alloy on residual stress, welding force and macrostructure. The International Journal of Advanced Manufacturing Technology. 2018;95(5-8):2757-2766. [Link] [DOI:10.1007/s00170-017-1431-6]
21. Alinaghian I, Amini S, Honarpisheh M. Residual stress, tensile strength, and macrostructure investigations on ultrasonic assisted friction stir welding of AA 6061-T6. The Journal of Strain Analysis for Engineering Design. 2018;53(7):030932471878976 [Link] [DOI:10.1177/0309324718789768]
22. Kelleher J, Prime MB, Buttle D, Mummery PM,Webster PJ, Shackleton J,Withers PJ. The measurement of residual stress in railway rails by diffraction and other methods. Journal of Neutron Research. 2003;11(4):187-193. [Link] [DOI:10.1080/10238160410001726602]
23. DeWald AT, Rankin JE, Hill MR, Lee MJ, Chen H. Assessment of tensile residual stress mitigation in alloy 22 welds due to laser peening. Journal of Engineering Materials and Technology. 2004;126(4):1-9. [Link] [DOI:10.1115/1.1789957]
24. Nazari F, Honarpisheh M, Zhao H. Effect of stress relief annealing on microstructure, mechanical properties, and residual stress of a copper sheet in the constrained groove pressing process. The International Journal of Advanced Manufacturing Technology. 2019;102(9-12):4361-4370. [Link] [DOI:10.1007/s00170-019-03511-w]
25. Raygan S, Rassizadehghani J, Askari M. Comparison of Microstructure and Surface Properties of AISI 1045 Steel After Quenching in Hot Alkaline Salt Bath and Oil. Journal of Materials Engineering and Performance. 2009;18(2):168-173. [Link] [DOI:10.1007/s11665-008-9273-x]
26. Rassizadehghani J, Raygan S, Askari M. Comparison of the quenching capacities of hot salt and oil baths. Metal Science and Heat Treatment. 2006;48(5-6):193-198. [Link] [DOI:10.1007/s11041-006-0069-z]
27. Malekan A, Pedram A, Raygan S, Rassizadeh Ghani J, Malekan M. The influence of alkaline salt bath quenching on the microstructure and mechanical properties of AISI D2 steel. Canadian Metallurgical Quarterly. 2014;53(1):88-92. [Link] [DOI:10.1179/1879139513Y.0000000102]
28. Olson MD, DeWald AT, Prime MB, Hill MR. Estimation of uncertainty for contour method residual stress measurements. Experimental Mechanics. 2015;55(3):577-585. [Link] [DOI:10.1007/s11340-014-9971-2]
29. Adediran A, Aribo S, Amuda M. Mechanical properties of dual phase steel quenched in bitumen medium. Leonardo Electronic Journal of Practices and Technologies. 2015;14(26):1-16. [Link]
30. Singh RR, Gaikwad A, Singh SS, Singh V. Comparison of mechanical properties of medium carbon steel with dual phase steel. International Journal of Mechanical Engineering. 2015;4(4):1-8. [Link]
31. Hassan SB, Balogun SO, Aigbodion VS. Hardening characteristics of medium carbon steel using fresh cassava liquid extract as quenchants. Journal of Metallurgy and Materials Engineering, 2009;4(2):55-61. [Link]
32. Dauda M, Kuburi LS, Obada DO, Mustapha RI. Effects of varios quenching media on mechanical properties of annealed 0.509Wt%C -0.178Wt%Mn steel. Nigerian Journal of Technology. 2015;34(3):506-512. [Link] [DOI:10.4314/njt.v34i3.12]
33. Gündüz S, Çapar A. Influence of forging and cooling rate on microstructure and properties on medium carbon microalloy forging steel. Journal of Materials Science. 2006;41(2):561-564. [Link] [DOI:10.1007/s10853-005-4239-y]
34. Callister WD. Fundamentals of materials science and engineering. 5th Edition. London, UK: Wiley; 2000. [Link]
35. Odusote JK, Ajiboye TK, Rabiu AB. Evaluation of mechanical properties of medium carbon steel quenched in water and oil. Journal of Minerals and Materials Characterization and Engineering. 2012;11(9):859-862. [Link] [DOI:10.4236/jmmce.2012.119079]
36. Shirdel A, Khajeh A, Moshksar MM. Experimental and finite element investigation of semi-constrained groove ressing process. Materials and Design. 2010;31(2):946-950. [Link] [DOI:10.1016/j.matdes.2009.07.035]
37. Honarpisheh M, Tavajjohi MH, Nazari F. Experimental and numerical study of severe plastic deformation in the constrained groove pressing process on the pure copper sheets. Modares Mechanical Engineering. 2019;19(2):269-280. [Persian] [Link]
38. Liscic B, Tensi HM, Canale LCF, Totten GE. Quenching theory and technology. 2nd Edition. Boca Raton: CRC Press, Taylor and Francis Group; 2010. [Link] [DOI:10.1201/9781420009163]
Send email to the article author
| Rights and permissions | |
 |
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. |