Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1393
11
1
gregorian
2015
2
1
14
11
online
1
fulltext
fa
بررسی قابلیت ماشینکاری قطعات متالورژی پودر خام و تف جوشی شده آهن/چدن آسیاب پاششی شده
Investigation of machinability of green and sintered iron-jet milled cast iron powder metallurgy parts
در این تحقیق به بررسی قابلیت ماشینکاری قطعات متالورژی پودر خام و تفجوشی شده آهن-چدن خاکستری بازیابی شده پرداخته میشود. برای این منظور برادههای چدن خاکستری با استفاده از روش آسیاب پاششی تبدیل به پودر شده و در ترکیب با پودر آهن تجاری برای تهیه قطعات متالورژی پودر مورد استفاده قرار گرفتند. خشته-های خام با متغیرهای درصد پودر چدن و فشار تراکم تهیه شدند. برای قطعات تفجوشی شده نیز طراحی آزمایش با روش رویه پاسخ و با متغیرهای درصد پودر چدن، فشار تراکم، دمای تفجوشی و زمان تفجوشی و هر کدام در پنج سطح انجام شد. تحلیلهای رگرسیون و واریانس برای بررسی تأثیر پارامترهای ورودی، ارائه مدلهای ریاضی و ارزیابی صحت مدلها به کار رفتند. در بخش خام قابلیت ماشینکاری در عملیات سوراخکاری به صورت کیفی مورد بررسی قرار گرفت. در قطعات تفجوشی شده نیز قابلیت ماشینکاری از طریق اندازهگیری نیروهای محوری و گشتاوری و زبری سطح حاصل از عملیات سوراخکاری بررسی شد. نتایج به دست آمده صحت معادلات رگرسیون استخراجی برای پیش بینی خواص ماشینکاری این قطعات را تأیید کرد. همچنین نتایج نشان دادند که افزودن پودر چدن خاکستری به دست آمده از روش آسیاب پاششی باعث بهبود قابلیت ماشینکاری قطعات متالورژی پودر پایه آهنی میشود.
In this research, the machinability of iron-recycled grey cast iron powder metallurgy parts is investigated. For this purpose, grey cast iron swarfs were transformed to powders by target jet milling method and were then used to prepare powder metallurgy parts in combination with commercial iron powder. Green compacts were prepared with the variables of cast iron powder percentage and compaction pressure. Design of experiments was conducted by response surface method for sintered parts with the variables of cast iron powder percentage, compaction pressure, sintering temperature and sintering time each in five levels. Regression analysis and analysis of variance were used to investigate the effect of input parameters, develop the mathematical models and evaluate the validity of the models. In the green section, machinability was qualitatively investigated in drilling. For sintered parts, machinability was evaluated by measuring the thrust and torque forces and the obtained surface finish in drilling. The obtained results certificated the accuracy of the extracted regression equations for predicting the machining properties of the parts. Also, the results demonstrated that the addition of jet milled grey cast iron improves the machinability of iron-based powder metallurgy parts.
قابلیت ماشینکاری,تفجوشی,آسیاب پاششی,متالورژی پودر,چدن خاکستری
Machinability,Sintering,Jet milling,Powder metallurgy,Grey cast iron
59
67
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-7873&slc_lang=fa&sid=15
Hadi
Abdollahi
هادی
عبداللهی
100319475328460053375
100319475328460053375
Yes
استادیار، مهندسی مکانیک، دانشگاه صنعتی ارومیه، ارومیه
Rouhollah
Panahi
روح اله
پناهی لیاولی
100319475328460053385
100319475328460053385
No
مربی، مهندسی مکانیک، دانشگاه فنی و حرفه ای، تهران
Ramezan Ali
Mahdavinejad
رمضانعلی
مهدوی نژاد
100319475328460053386
100319475328460053386
No
دانشیار، مهندسی مکانیک، دانشگاه تهران، تهران
Vahid
Zal
وحید
زال
100319475328460053387
100319475328460053387
No
دانشجوی دکترای مهندسی مکانیک، دانشگاه تربیت مدرس