Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1395
11
1
gregorian
2017
2
1
16
12
online
1
fulltext
fa
بررسی زبری سطح در تراشکاری لولههای کامپوزیتی با الیاف شیشه و رزین اپوکسی
Investigation of Surface Roughness in Turning of Epoxy-Glass Composite Tubes
امروزه کامپوزیتها در مقایسه با فلزها، با توجه به برخورداری از خواص مکانیکی بالا نسبت به وزن و مقاومت به خوردگی خوب، کاربرد گسترده ای در صنایع مختلف از جمله هوافضا، خودرویی و دفاعی پیدا نمودهاند. ماشینکاری این مواد با توجه به ساختار مرکب آنها، از پیچیدگی خاصی برخوردار است. دستیابی به شرایط بهینه ماشینکاری، بسته به نوع نیاز، با توجه به نوع الیاف و رزین مصرف شده در کامپوزیتها، به بررسی دقیق و تحلیلهای مناسب نیاز دارد. در تحقیق حاضر، لولههای کامپوزیتی از جنس شیشه-اپوکسی به ضخامت 5 میلیمتر، که اغلب در بدنه سازههای هوافضایی کاربرد دارند، با لایه چینی دستی تولید شده اند و زبری سطح آنها پس از فرآیند تراشکاری اندازه گیری شده است. بدین منظور، جهت بدست آوردن حداقل زبری در فرایند تراشکاری، نوع ابزار در دو حالت، و سرعت برشی، نرخ پیشروی و عمق برشی، در سه سطح مختلف مورد بررسی قرار گرفته است. پس از طراحی آزمایش با روش تاگوچی و انجام آزمایش بر روی نمونههای از پیش ساخته شده، زبری سنجی و تحلیلهای مد نظر انجام پذیرفت. در نهایت نتیجه گیری گردید که حداقل میزان زبری از ابزار با سطوح برادهشکن، سرعت برشی m/min 100، نرخ پیشرویmm/rev 0.05 و عمق برش mm 1.5 بدست خواهد آمد.
Today, composite materials have extensive use in aerospace automotive and defense industries compared to metals, because of their high strength to weight ratio and good corrosive resistance. Machining of these materials regard to their composite structure is complicated. Achieve optimal machining conditions, depending on the needs, according to the type of fiber and resin used in composites, need proper analysis and careful investigation. In this study, composite pipes made of glass-epoxy to a thickness of 5 millimeters, which are often used in the body of Aerospace structures, produced by hand lay-up and their surface roughness after turning process is measured. In order to obtain the minimum roughness in the turning process, tool type in two modes, and cutting speed, feed rate, and depth of cut are studied at three different levels. So Taguchi experimental design method and experimental test samples on roughness the results analysis and performed by minitab software. Finally, concluded that the minimum value of the surface roughness is obtained by tools with chip-breaking levels, cutting speed 100 m/min, feed rate 0.05 mm/rev, and the depth of cut 1.5 mm.
زبری سطح,کامپوزیت اپوکسی-شیشه,تراشکاری
Surface roughness,Epoxy-glass Composite,Turning
629
636
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-8592&slc_lang=fa&sid=15
Majid
Azad Hassan
مجید
آزاد حسن
100319475328460065813
100319475328460065813
No
دانشگاه آزاد اسلامی-واحد تهران شمال
Ehsan
Shakouri
احسان
شکوری
100319475328460065812
100319475328460065812
Yes
Islamic Azad University-tnb
- استادیار
- مدیرکل خدمات پژوهش و تولید علم
- دانشگاه آزاد اسلامی-واحد تهران شمال
Payam
Saraeian
پیام
سرائیان
100319475328460065811
100319475328460065811
No
دانشگاه آزاد اسلامی-واحد تهران شمال