Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1394
6
1
gregorian
2015
9
1
15
7
online
1
fulltext
fa
بررسی رفتار مذاب آلومینیم و نیروی انقباضی در جفت فلزی آلومینیم- منیزیم ریختهگری شده به روش ریختهگری گریز از مرکز
Melt Behavior and Shrinkage Force Effect of Al Melt in Al/Mg Bimetal Casted via Centrifugal Casting
مصرف قطعات منیزیمی و آلومینیمی با هدف کاهش وزن نهایی قطعات در صنایع مختلف بهطور روز افزون افزایش یافته است. در این پژوهش ریختهگری جفت فلزی آلومینیم- منیزیم در حالت ذوبریزی مذاب آلومینیم درون جامد منیزیم به شکل استوانهی توخالی در ابعاد، ارتفاع 35 میلیمتر و قطر داخلی و خارجی 84 و 76 میلیمتر، در سرعتهای دوران 1200 و 1600 دور بر دقیقه، نسبتهای حجمی مذاب- جامد 9/0، 6/1 و 7/2 و دماهای پیشگرم 30، 120، 150 و 200 درجهی سانتیگراد به-وسیلهی دستگاه ریختهگری گریز از مرکز عمودی انجام شد و فصل مشترک تشکیل شده مورد بررسی و مطالعه قرار گرفت. در خلال ریختهگری رفتار مذاب آلومینیم تابع نیروهای گرانشی، گریز از مرکز، کوریولیوس و همچنین دمای پیشگرم جامد است. در این حالت تفاوت در میزان انقباض آلومینیم و منیزیم، نسبت به یکدیگر، منجربه ایجاد اتصال مکانیکی میشود. بررسیهای آنالیز میکروسکوپ الکترونی مجهز به طیفسنجی پراش انرژی پرتو ایکس(EDS) و آنالیز پراش اشعهی ایکس (XRD)، آن نشان داد که مقدار آلومینیم در فصل مشترک از سمت منیزیم به طرف آلومینیم طوری افزایش یافته که باعث ایجاد گرادیان غلطتی و تشکیل ترکیبات بین فلزیAl3Mg2 و Al12Mg17 و ساختار یوتکتیک، مطابق دیاگرام تعادل، میشود.
Applications of aluminium and magnesium castings have been increased, as a result of increasing demand for the light weight components in various sectors of industries, in recent years. In this work an Al/Mg bimetal was prepared by casting Al melt into a cylindrical Mg bush, with 35 mm height and 76 and 84 inner and outer inner diameter, rotating at 1200 and 1600 revolutions per minute (rpm), 0.9, 1.6 and 2.7 melt-to-solid volume ratio and 30, 120, 150 and 200 oC preheating temperature, respectively. Vertical centrifugal casting process was selected for producing samples. In this process melt is under effect of centrifugal, coriolis and gravity forces during filling. Difference between shrinkage of Al and Mg led to the formation of mechanical bond in the interface. The results of scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) analysis showed that concentration gradient changes from Mg to Al side in such a way that three sub layers including Al3Mg2 and Al12Mg17 intermetallics plus eutectic microstructure (Al12Mg17 and δ), were formed, based on aluminium and magnesium phase diagram, in the interface
فصل مشترک,نیروهای انقباضی,آلومینیم,منیزیم,اتصال مکانیکی
interface,shrinkage force,mechanical bond,Al,Mg
131
138
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-8914&slc_lang=fa&sid=15
Morteza
Sarvari
مرتضی
سروری
100319475328460057296
100319475328460057296
No
Iran university of science and tehnology
دانشگاه علم و صنعت ایران
Mehdi
Divandari
مهدی
دیواندری
100319475328460057281
100319475328460057281
Yes
Iran University of Science and Technology
دانشگاه علم و صنعت ایران