Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1395
7
1
gregorian
2016
10
1
16
8
online
1
fulltext
fa
مطالعه تجربی تاثیر اندازه ذرات ساینده و سختی قطعه کار در فرآیند جریان ساینده مغناطیسی
Experimental study of the effects of abrasive particle size and work piece hardness in Magnetic abrasive flow Machining
ماشین کاری با جریان ساینده(AFM) یک فرآیند نسبتا جدید با نرخ براده برداری کم برای پلیسهگیری، برداشت لایههای سفید و پرداختکاری قطعات صنعتی با شکل پیچیده در میان فرآیندهای غیر سنتی میباشد که عمل پرداختکاری در آن، از طریق جریان یک ترکیب ویسکو الاستیک حامل ذرات ساینده تحت فشار پیستون بر روی سطح مورد نظر صورت میگیرد. در این پژوهش فرآیند ماشینکاری جریان ساینده در پرداخت کاری فولاد ابزار گرم کار H13 مورد بررسی قرار گرفته و با اعمال یک میدان مغناطیسی خارجی حول قطعه کار سعی در افزایش نرخ براده برداری و صافی سطح شده است و تاثیر شدت میدان مغناطیسی، مش ذرات ساینده و سختی قطعه کار بعنوان پارامترهای ورودی فرآیند بر روی خروجیهای فرایند شامل زبری سطح و نرخ براده برداری مطالعه شده است. همچنین مدل رگرسیونی نرخ براده برداری و زبری سطح توسعه داده شده و آنالیز واریانس آنها نیز انجام شد. نتایج این مطالعه نشان داد که افزایش مش ذرات ساینده سبب کاهش زبری سطح و نرخ براده برداری میگردد، از طرفی افزایش شدت میدان مغناطیسی موجب زیاد شدن نرخ برداشت ماده و بهبود صافی سطح میگردد. همچنین با افزایش سختی قطعه کار نرخ براده برداری شده کاهش یافته و در شرایط یکسان پرداخت، صافی سطح بدست آمده نیز بیشتر میشود.
Abrasive flow machining (AFM) is a relatively new process with low material removal ratio for deburring, removing recast layers and finishing industrial components with complex shapes among non-conventional machining processes. In this process, the finishing is handled by flowing of the composition of viscoelastic and abrasive particles on workpiece surface, under the pressure of piston. In this research, the abrasive flow machining process of H13 tool steel with applied an external magnetic field around the workpiece for improve the material removal ratio and surface roughness has been investigated and the effect of magnetic field intensity, abrasive particles mesh and the hardness of workpiece as the input parameters on the process outputs including surface roughness and material removal ratio was studied. Also the regression model of MRR and surface roughness was developed and variance analysis was performed. Results of experiments indicated that increase in abrasive-particles mesh leads to decrease surface roughness and material remove ratio and increase in magnetic field intensity causes to increase material removal ratio and decrease surface roughness. Also the material removal ratio is decreased with increasing of workpiece hardness and on the same condition; better surface finish was achieved in the case of harder workpiece.
جریان ساینده,جریان ساینده مغناطیسی,زبری سطح,نرخ براده برداری,فولاد H13
Abrasive flow,magnetic abrasive flow,Surface roughness,material removal,H13 steel
131
138
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-1879&slc_lang=fa&sid=15
Mohammad Reza
Shabgard
محمدرضا
شبگرد
100319475328460063514
100319475328460063514
Yes
دانشیار تبریز-دانشگاه تبریز- ریاست دانشکده فنی مهندسی مکانیک-گروه مهندسی ساخت و تولید- محمد رضا شبگرد
Farzam
Arabzadeh Tabriz
فرزام
عربزاده تبریز
100319475328460063515
100319475328460063515
No
Department of Mechanical Engineering, Tabriz University, Tabriz, Iran
دانشجوی کارشناسی ارشد، مهندسی مکانیک، دانشگاه تبریز، تبریز، ایران
Ahad
Gholipoor
احد
قلی پور
100319475328460063500
100319475328460063500
No
Department of Mechanical Engineering, Tabriz Branch, Islamic Azad University, Tabriz, Iran
مربی، مهندسی مکانیک، واحد تبریز، دانشگاه آزاد اسلامی، تبریز، ایران