Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1395
11
1
gregorian
2017
2
1
16
12
online
1
fulltext
fa
اثرشرایط کاری روی عملکرد بهینه یک سیکل سرمایش جذب سطحی دو بستره
The effect of operating conditions on the optimal performance of a two-bed adsorption cooling cycle
در این پژوهش تحلیل انرژی و اگزرژی یک سیستم سرمایش جذب سطحی انجامشده است. سیلیکاژل و آب بهعنوان جفت جاذب-جذب شونده در سیستم بهکاررفته است. تحلیل با هدف تعین اثر پارامترهای عملکردی روی زمان بهینه و سپس روی مقدار بیشینه ظرفیت سرمایش ویژه، ضریب عملکرد و تأثیرپذیری و مقدار کمینه بازگشتناپذیریهای داخلی و خارجی انجام میشود. جهت رسیدن به این هدف یک مدل ریاضی ظرفیت فشرده به همراه یک روش بهینهسازی با نام الگوریتم pso استفادهشده است. در این مدل بازگشتناپذیریهای داخلی و خارجی با روشی جدید و بدون محاسبه بازگشتناپذیریهای اجزای داخلی سیکل محاسبه میشود. تحلیل انرژی نشان میدهد با افزایش دما و دبی جرمی آب گرم ورودی، ماکزیمم مقدار ظرفیت سرمایش ویژه افزایش مییابد و افزایش دمای آب گرمکننده باعث افزایش ضریب عملکرد میشود اما افزایش دبی جرمی آب گرمکننده ضریب عملکرد را کاهش میدهد. تحلیل اگزرژی نشان میدهد بسته به مقدار دما و دبی جرمی آب گرم ورودی 65-90 درصد از اگزرژی ورودی بهوسیله بازگشتناپذیریهای داخلی، 1-20 درصد بهوسیله بازگشتناپذیریهای خارجی از بین رفته و 8-14 درصد آن به منبع دماپایین منتقلشده است. همچنین نتایج نشان میدهد در دماهای پایین برای آب گرم ورودی اگر دبی جرمی کمتر از 0.6 باشد، تأثیرپذیری برای دمای 75 درجه بیشتر از 65 خواهد بود.
In this study, energy and exergy analysis of a two bed adsorption cooling system have been performed. Silica gel-water has been chosen as the adsorbent-refrigerant pair. Analysis is performed for evaluating the effect of operating conditions on the optimal timing and then on the maximum value of the SCP, COP, effectiveness and the minimum value of internal irreversibility and external irreversibility. A lumped parameter mathematical model and a global optimization method called the particle swarm optimization have been used to reach this purpose. In this model, internal and external irreversibility have been calculated with the new method without calculating irreversibility of the cycle internal component. Energy analysis showed that maximum of SCP increases with the increase of the mass flow rate and heat source temperature. Furthermore, an increase in the heat source temperature causes an increase in the COP, but an increase of the mass flow rate causes a decrease in the COP. Exergy analysis reviled that depending on the mass flow rate and heat source temperature, 65-90% of input exergy was expended by internal irreversibility, 1–20% were expended by external irreversibility and 8-14% is transferred to the cold reservoir in evaporator. It is concluded at the low-temperature heat source if the mass flow rate is chosen less than 0.6 kg/effectiveness at heat source temperature 75 is more than 65 and vice versa.
سیستم جذب سطحی,اگزرژی,تأثیرپذیری,ضریب عملکرد
Adsorption system,Exergy,Effectiveness,coefficient of performance
583
592
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-2214&slc_lang=fa&sid=15
Mohammad
Sharifzadeh
محمد
شریف زاده
100319475328460065795
100319475328460065795
No
دانشگاه فردوسی مشهد
Mohsen
Ghazikhani
محسن
قاضی خانی
100319475328460065796
100319475328460065796
Yes
دانشگاه فردوسی مشهد
Hamid
Niazmand
حمید
نیازمند
100319475328460065797
100319475328460065797
No
دانشگاه فردوسی مشهد