Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1392
12
1
gregorian
2014
3
1
13
15
online
1
fulltext
fa
بررسی سختی و رفتار فشاری نانوکامپوزیت آلومینیوم/ الیاف کوتاه شیشه تولید شده به روش آسیاب گلوله ای و پرس گرم
Investigation of hardness and compression behavior of Al/Short glassf nanocomposite produced by ball milling and hot pressing
آلیاژ نانوساختار آلومینیومی (Al-8wt%Zn-3wt%Mg) بوسیله دو مکانیزم همزمان شکست و جوش سرد آلیاژسازی مکانیکی بر روی پودرهای اولیه عناصر تشکیل دهنده، تولید شد و از این آلیاژ نانوساختار به عنوان زمینه برای نانوکامپوزیت Al/Short glass fiber استفاده شد. پودر نانوکامپوزیت تولید شده با روش آلیاژسازی مکانیکی، تحت فشار MPa 400 و در دمای C°380 در قالب استوانه ای پرس گرم شده و نمونه نانوکامپوزیت بالک ساخته شد. چگالی نسبی و خواص مکانیکی همچون سختی، استحکام فشاری این نانوکاپوزیت در درصدهای وزنی 1، 3 و 5 از الیاف کوتاه شیشه مورد بررسی قرار گرفت. چگالی نسبی در نمونه با 5 درصد تقویت کننده بسیار کمتر از نمونه 1 و 3 درصد شده و این موضوع نشان دهنده افزایش شدید تخلخل ها در فصل مشترک فاز زمینه و تقویت کننده در نمونه با 5 درصد الیاف شیشه است. استحکام فشاری و سختی از نمونه 1 به 3 درصد افزایش ولی در 5 درصد به دلیل کاهش شدید در چگالی، کاهش یافت. همچنین استحکام فشاری نانوکامپوزیت با زمینه های آلومینیوم آلیاژی و آلومینیوم خالص مورد مقایسه قرار گرفت و نتایج نشان دهنده تقویت کنندگی بیشتر در نمونه با زمینه آلومینیوم خالص می باشد.
Nanostructured (Al-8wt%Zn-3wt%Mg) alloy was synthesized by simultaneous fracture and cold welding mechanisms in mechanical alloying with initial elemental powders and subsequently, this alloy was applied as matrix to fabricate Al/Short glass fiber nanocomposite in 1, 3 and 5 percent of glass fibers. The resulting powders were consolidated under 400 MPa at 380 °C in cylindrical die to produce consolidated nanocomposites. Relative density of samples reduced with increasing the percentage of glass fibers and this trend was more intense from 3 to 5 percent. Also compressive strength and hardness were investigated for these samples in different percent of glass fiber. The results showed that strength and hardness were enhanced with increasing glass fiber but decrease of mechanical properties was observed in 5 percent due to reducing in relative density. Compressive strength was compared between nanocomposite with pure Al and Al alloy matrix, and results show more reinforcement in Al based sample.
نانوکامپوزیت زمینه آلومینیومی,خواص مکانیکی,آسیاب کاری گلوله ای,پرس گرم,الیاف شیشه
Aluminum Based Nanocomposite,Mechanical properties,Ball Milling,Hot pressing,glass fiber
50
58
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-2630&slc_lang=fa&sid=15
علی
شکوه فر
100319475328460051128
100319475328460051128
Yes
دانشگاه صنعتی خواجه نصیرالدین طوسی
Amin
Azimi
امین
عظیمی
100319475328460051127
100319475328460051127
No
دانشگاه صنعتی خواجه نصیرالدین طوسی
Ashkan
Zolriasatein
اشکان
ذوالریاستین
100319475328460051126
100319475328460051126
No
دانشگاه صنعتی خواجه نصیرالدین طوسی
Ali-Asghar
jafari
علی اصغر
جعفری
100319475328460051125
100319475328460051125
No
دانشگاه صنعتی خواجه نصیر الدین طوسی