Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1394
11
1
gregorian
2016
2
1
15
12
online
1
fulltext
fa
بررسی تاثیر تنشهای پسماند ناشی از کوئنچ و ماشینکاری بر اعوجاج قطعات جدارنازک
Effect of machining and quench-induced residual stress on the distortion
of thin-walled parts
یکی از مشکلات اصلی در ماشینکاری قطعات جدار نازک از جنس آلیاژهای استحکام بالای آلومینیم، اعوجاج و ناپایداری ابعادی قطعات بعد از ماشینکاری است که منجر به افزایش نرخ قطعات معیوب و افزایش هزینههای تولید میگردد. در این مقاله رابطه تنشهای پسماند ناشی از کوئنچ و ماشینکاری قطعات، با میزان اعوجاج یک قطعه جدار نازک از جنس آلیاژ 7075Al مورد بررسی قرار گرفته است. بدین منظور، دو گروه آزمایش انجام شده است. در مرحله اول به بررسی ارتباط تنشهای پسماند ناشی از فرایند کوئنچ با اعوجاج پرداخته شده است. با انجام آزمایشهای تجربی، اثر بخشی دو روش کوئنچ پلیمری و کوئنچ معکوس در کاهش تنشهای پسماند در مقایسه با کوئنچ در آب بررسی شده است و رابطه سطح تنشها با میزان اعوجاج بررسی شده است. در مرحله دوم با آزمایشهایی با شرایط مختلف ماشینکاری و اندازهگیری نیرو، حرارت و تنش پسماند در قطعات، تاثیر این پارامترها بر میزان اعوجاج قطعات بررسی شده است. نتایج به دست آمده نشان میدهد هر دو نوع تنش، در ایجاد اعوجاج در قطعات موثر هستند و که میبایست با انتخاب استراتژیهای مناسب تا حد امکان سطح این تنشها را کاهش داد.
The main problems in machining of thin-walled parts made of high-strength aluminum alloys are distortion and dimensional instability, which lead to an increase in distorted part scraps and production costs. This article attempts to investigate the correlation between machining-induced and quench-induced residual stresses and the distortion of thin-walled parts made of AL7075 alloy. The experiments are carried out in two steps. In the first step, the effects of polymer and uphill quenching methods in comparison with water quenching in the reduction of residual stresses are investigated on an experimental basis. By conducting the machining tests, the effect of residual stress on distortion is investigated. In the second step, several experiments are carried out under different machining conditions. To study the effect of mechanical and thermal loads on the residual stresses and distortion, the machining force and temperature of cutting area are measured. Finally, the correlation between the machining-induced residual stress and distortion is studied by measurement of stress on some parts. The results indicate that both machining and quench-induced residual stresses are effective in distortion of thin walled parts.
تنش پسماند,اعوجاج,ماشینکاری,کوئنچ,قطعات جدار نازک,آلیاژ 7075-Al
Residual Stress,Distortion,Machining,Quenching,Thin-walled part,AL7075
357
366
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-3704&slc_lang=fa&sid=15
Saeed
Amini
سعید
امینی
100319475328460059886
100319475328460059886
Yes
دانشیار دانشکده مهندسی مکانیک، دانشگاه کاشان
Soroush
Masoudi
سروش
مسعودی
100319475328460059887
100319475328460059887
No
فارغ التحصیل کارشناسی ارشد
Ghasem
Amirian
قاسم
امیریان
100319475328460059888
100319475328460059888
No
هیئت علمی