Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1393
5
1
gregorian
2014
8
1
14
5
online
1
fulltext
fa
اثر معیارهای تسلیم هاسفورد، هیل درجه 2 و غیر درجه 2 بر منحنیهای حد شکلدهی بر حسب مدل M-K
The effects of Hosford, Hill’s quadratic and non-quadratic yield criteria on prediction of forming limit diagrams based on M-K Model
یکی از پارامترهای مهم در پیشبینی شکلدهی ورقهای فلزی تاثیر معیارهای تسلیم بر پیشبینی کرنشهای حدی می¬باشد. در این مقاله اثرات ضریب ناهمسانگردی نرمال بر معیارهای تسلیم ناهمسانگرد درجه 2 هیل (1948)، مرتبه بالاتر هاسفورد (1979) و غیر درجه 2 هیل (1979)، با توجه به موقعیت کرنش صفحهای بررسی شده و همچنین اثر این معیارهای تسلیم و پارامترهای ضریب ناهمسانگردی نرمال، ضریب حساسیت به نرخ کرنش، توان کرنش سختی و درجه¬ی معیار تسلیم بر منحنیهای حد شکلدهی بر حسب مدل M-Kمورد مطالعه قرار گرفته است. اثرات متفاوت ضریب ناهمسانگردی نرمال بر روی کرنشهای حدی سه معیار فوق تطابق خوبی با اثر ضریب ناهمسانگردی نرمال بر روی سطوح مختلف تسلیم دارد. مقایسه¬ای بین اثر درجه معیار تسلیم و ضریب ناهمسانگردی نرمال برای معیار تسلیم غیر درجه 2 هیل نیز صورت گرفته است. نتایج نشان داده است که انتخاب معیار تسلیم تاثیر زیادی بر روی منحنی حد شکلدهی دارد.
One of the most important parameters in prediction of sheet metal forming process is the influence of yield criteria on prediction of forming limit strains. In this paper, the effects of normal anisotropy coefficient on the Hill’s (1948) quadratic, Hosford’s (1979) higher-order, Hill’s (1979) non-quadratic anisotropic yield criteria, with attention to plane strain location is studied. Also the effects of these yield criteria and normal anisotropy coefficient, strain rate sensitivity factor, strain hardening exponent and yield criterion exponent on the forming limit diagram based on the M-K model have been discussed. The different effects of normal anisotropy coefficient on the limit strains of three above criteria have a good agreement with the effect of normal anisotropy coefficient on the yield different surfaces. The comparison has been made between yield criterion exponent and normal anisotropy coefficient effect on the Hill’s non-quadratic yield criterion. The results show that the proper selection of yield criterion have a significant influence on the forming limit diagram.
معیار تسلیم,ناهمسانگردی,منحنیهای حد شکلدهی,مدل M-K
Yield criterion,Anisotropy,forming limit diagrams,M-K model.
137
146
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-4058&slc_lang=fa&sid=15
Mohammad
Hoseinpour
محمد
حسین پور گللو
100319475328460052114
100319475328460052114
Yes
استادیار عضو هیئت علمی دانشگاه شهید رجایی
Seyed Mohammad Hossein
Seyedkashi
سید محمدحسین
سیدکاشی
100319475328460052111
100319475328460052111
No
2- استادیار عضو هیئت علمی دانشگاه بیرجند
Narjes
Valyan
نرجس
ولیان
100319475328460052112
100319475328460052112
No
دانشجوی کارشناسی دانشگاه تربیت دبیر شهید رجایی