Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1395
11
1
gregorian
2017
2
1
16
12
online
1
fulltext
fa
شبیه سازی سه بعدی اجزای محدود فرایند میکروفرزکاری آلیاژ تیتانیوم
3D Finite element simulation of micro-milling process of titanium alloy
امروزه با ظهور سیستم های کامپیوتری پیشرفته تر، امکان شبیه سازی و مدل کردن مسایل بسیار پیچیده با دقت های بالاتر میسر گردیده و از این رو استفاده از شبیه سازی های نرم افزاری بعنوان روشی جایگزین بجای آزمایش های فیزیکی در تحلیل و بهینه سازی عملکرد فرایندها با رویکرد کاهش هزینه و زمان مصرفی، بیش از پیش مورد توجه قرار گرفته است. بکارگیری این روش ها در مورد میکروفرایندها که مشکلات اندازه گیری های تجربی بعلت کاهش مقیاس از ماکرو به میکرو بیشتر می شود، اهمیت بسزایی یافته است. در این تحقیق از یک مدل سه بعدی برای شبیه سازی فرایند میکروفرزکاری در نرم افزار دیفرم استفاده شده است. اثر پارامترهای برشی بر مشخصه هایی از فرایند نظیر نیروی برش، دما و سایش ابزار مورد ارزیابی قرار گرفت. برای اعتبارسنجی مدل از نتایج نیرویی اندازه گیری شده به روش تجربی استفاده شد که مطابقت بسیار زیادی بین نتایج شبیه سازی و تجربی مشاهده گردید. نتایج نشان از قابلیت بالای مدل تهیه شده در پیش بینی رفتار فرایند داشته است.
Nowadays, emerging more advanced computer systems made it possible to simulate and model complex problems even with higher accuracy. Regarding lower time and cost, the use of simulations instead of physical experiments is increasingly considered as an alternative method in the analysis and optimization of process performance. The importance of such methods becomes more significant when talking about micro-processes, since there are lots of difficulties in experimental measurements as a results of scaling problems by scaling down from macro to micro. In this study, a 3D model is developed using Deform-3D software for prediction of micromilling process behavior. Effects of cutting parameters on such characteristics as cutting forces, temperature distribution and tool wear are investigated. To check the validity of the model, force results of simulation are compared with the measured ones. A high level of correlation exists between the obtained simulation and measured results which shows that the 3D developed model has good capability to predict process behavior.
میکروفرزکاری,شبیه سازی,نیروی برش,دما,سایش ابزار,آلیاژ تیتانیوم
Micromilling,Simulation,cutting force,temperature,Tool wear,Titanium alloy
555
561
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-6104&slc_lang=fa&sid=15
Hamed
Rezaei
حامد
رضایی
100319475328460065792
100319475328460065792
No
شرکت مجتمع گاز پارس جنوبی
Mohamad Hosein
Sadeghi
محمد حسین
صادقی
100319475328460065777
100319475328460065777
Yes
هیئت علمی دانشگاه تربیت مدرس