Modares Mechanical Engineering
مهندسی مکانیک مدرس
Modares Mechanical Engineering
Engineering & Technology
http://mme.modares.ac.ir
1
admin
1027-5940
2476-6909
10.22034/mme
fa
jalali
1392
6
1
gregorian
2013
9
1
13
6
online
1
fulltext
fa
ارزیابی فرآیند بازپخت ورق پلی کربنات جهت رفع تنشهای پسماند
Evaluation of Annealing Process of Polycarbonate Sheet to Remove the Residual Stresses
در این مقاله فرآیندهای بازپخت موجود برای رهاسازی تنش و رفع تنشهای پسماند از صفحات پلی کربنات، مطالعه و با انجام آزمایش ارزیابی می شوند. سپس با اعمال تغییر و تصحیح بر آنها، عملیات حرارتی متعددی به صورت سعی و خطا بر روی نمونه های گوناگون اجرا می¬شود. با بررسی نتایج حاصله، فرآیند حرارتی مناسبی پیشنهاد می¬شود که امکان تنش زدایی از صفحه پلی¬کربنات را ضمن کاهش زمان و هزینه بازپخت فراهم نماید. طبق این فرآیند، ابتدا دما تا 100 درجه سانتی گراد با نرخ ˚C/h 20 افزایش داده می¬شود. نمونه¬ها به مدت 3 ساعت در این دما نگهداشته شده و سپس تا دمای 140درجه، افزایش دما با نرخ کمتر (˚C/h 5) ادامه می¬یابد. پس از آن نمونه ها با نرخ ˚C/h1 گرمتر می¬شوند تا به دمای بیشینه ˚C 156Tmax = برسند. پس از رسیدن به این نقطه، بلافاصله خنک کاری آغاز می شود و نرخ خنک کاری، مانند نرخ گرم کردن نمونه ها خواهد بود.
In this paper, annealing processes for stress relaxation and removing residual stresses from polycarbonate sheet are studied and evaluated using experimental tests. Then, by making some alterations and modifications in the previous heating cycles thermal operations are performed on different samples in a try and error process. Appraising the obtained results, a modified thermal cycle is presented which can remove the residual stress from the polycarbonate sample, while reducing the time and cost of the annealing process. According to this process, the temperature is raised to 100˚C at the heating rate of 20˚C/h. The samples are kept at this temperature for 3 hours and then, the heating is continued up to 140˚C at a slower rate of 5˚C/h. Then, the specimens are heated at the rate of 1˚C/h until maximum temperature of Tmax = 156˚C. After reaching this point, the samples are cooled immediately, and the cooling rates are same as the heating rates.
بازپخت,فرآیند حرارتی,تنش پسماند,پلی کربنات,حاشیه هم تنش
Anealing,Thermal Process,Residual Stress,polycarbonate,Isochromatic Fringe
103
113
http://mme.modares.ac.ir/browse.php?a_code=A-15-1000-7162&slc_lang=fa&sid=15
Mahnaz
Zakeri
مهناز
ذاکری
100319475328460041748
100319475328460041748
Yes
هیات علمی/ دانشکده هوافضا، دانشگاه صنعتی خواجه نصیرالدین طوسی