Volume 22, Issue 5 (May 2022)
Modares Mechanical Engineering 2022, 22(5): 335-345 |
Back to browse issues page
Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
akbari A H, saraeian P, Etemadi Haghighi S, Shakouri E. Evaluation the effect of adding CNT and CuO to the base fluid on the health and surface roughness of Inconel 718 MQL grinding. Modares Mechanical Engineering 2022; 22 (5) :335-345
URL: http://mme.modares.ac.ir/article-15-58168-en.html
URL: http://mme.modares.ac.ir/article-15-58168-en.html
1- Master, Department of Mechanical Engineering, College of mechanic, electronic, computer, Science and Research Branch, Islamic Azad University, Tehran, Iran
2- PHD, Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran ,p_saraeian@iau-tnb.ac.ir
3- PHD, Department of Mechanical Engineering, College of mechanic, electronic, computer, Science and Research Branch, Islamic Azad University, Tehran, Iran
4- PHD, Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
2- PHD, Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran ,
3- PHD, Department of Mechanical Engineering, College of mechanic, electronic, computer, Science and Research Branch, Islamic Azad University, Tehran, Iran
4- PHD, Department of Mechanical Engineering, North Tehran Branch, Islamic Azad University, Tehran, Iran
Abstract: (1868 Views)
Due to the difficulties and limitations in grinding hard materials, the use of nanoparticles in the Minimum Quantity Lubrication method can be effective as an appropriate solution to improve the efficiency of lubricating fluids. In this study, the effect of using a combination of carbon nanotubes and copper nano oxide on the surface quality of Inconel 718 alloy during grinding by Minimum Quantity Lubrication has been investigated.
The results showed that the use of nanoparticles in Rapeseed oil reduced the roughness and improved the surface health of the samples. The best surface topography with the least amount of pits and Furrows was obtained by combining nanoparticles with 3wt% in rapeseed oil, so that the surface roughness of the samples was reported 0.243 μm during this method, which is compared to the net use of CNT and CuO decreased by 14% and 7% respectively. Also, during the use of nanoparticles in minimum quantity lubrication, the amount of surface roughness compared to dry, flood and minimum quantity lubrication with rapeseed oil, decreased by about 35%, 13% and 18%, respectively.
Keywords: Grinding, Inconel 718, minimum quantity lubrication, surface Roughness and topography, carbon nanotube, CuO nanofluid
Article Type: Original Research |
Subject:
Machining
Received: 2021/12/26 | Accepted: 2022/01/30 | Published: 2022/04/30
Received: 2021/12/26 | Accepted: 2022/01/30 | Published: 2022/04/30
References
1. S. Debnath, M.M. Reddy, Q.S. Yi, Environmental friendly cutting fluids and cooling techniques in machining: a review, Journal of cleaner production, 83 (2014) 33-47. [DOI:10.1016/j.jclepro.2014.07.071]
2. P.H. Bee, S. Devaraj, M.C. Lahari, P.S.T. Sai, K. Narayanaswamy, A review on influence of nano-fluid MQL in machining processes, in: AIP Conference Proceedings, AIP Publishing LLC (2021) 1-7.
3. D. Zhang, C. Li, D. Jia, Y. Zhang, X. Zhang, Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding, Chinese Journal of Aeronautics, 28(2) (2015) 570-581. [DOI:10.1016/j.cja.2014.12.035]
4. Y. Zhang, C. Li, D. Jia, D. Zhang, X. Zhang, Experimental evaluation of MoS2 nanoparticles in jet MQL grinding with different types of vegetable oil as base oil, Journal of Cleaner Production, 87 (2015) 930-940. [DOI:10.1016/j.jclepro.2014.10.027]
5. Y. Zhang, C. Li, D. Jia, B. Li, Y. Wang, M. Yang, Y. Hou, X. Zhang, Experimental study on the effect of nanoparticle concentration on the lubricating property of nanofluids for MQL grinding of Ni-based alloy, Journal of Materials Processing Technology, 232 (2016) 100-115. [DOI:10.1016/j.jmatprotec.2016.01.031]
6. B. Li, C. Li, Y. Zhang, Y. Wang, D. Jia, M. Yang, N. Zhang, Q. Wu, Z. Han, K. Sun, Heat transfer performance of MQL grinding with different nanofluids for Ni-based alloys using vegetable oil, Journal of Cleaner Production, 154 (2017) 1-11. [DOI:10.1016/j.jclepro.2017.03.213]
7. F. Pashmforoush, R.D. Bagherinia, Influence of water-based copper nanofluid on wheel loading and surface roughness during grinding of Inconel 738 superalloy, Journal of Cleaner Production, 178 (2018) 363-372. [DOI:10.1016/j.jclepro.2018.01.003]
8. Y.S. Dambatta, M. Sayuti, A.A. Sarhan, M. Hamdi, S. Manladan, M. Reddy, Tribological performance of SiO2-based nanofluids in minimum quantity lubrication grinding of Si3N4 ceramic, Journal of Manufacturing Processes, 41 (2019) 135-147. [DOI:10.1016/j.jmapro.2019.03.024]
9. M. Seyedzavvar, M. Shabgard, M. Mohammadpourfard, Investigation into the performance of eco-friendly graphite nanofluid as lubricant in MQL grinding, Machining Science and Technology, (2019) 1-7. [DOI:10.1080/10910344.2019.1575403]
10. R.L. Virdi, S.S. Chatha, H. Singh, Processing characteristics of different vegetable oil-based nanofluid MQL for grinding of Ni-Cr alloy, Advances in Materials and Processing Technologies, (2020) 1-14. [DOI:10.1080/2374068X.2020.1800312]
11. J.C. Lopes, M.V. Garcia, R.S. Volpato, H.J. de Mello, F.S.F. Ribeiro, L.E. de Angelo Sanchez, K. de Oliveira Rocha, L.D. Neto, P.R. Aguiar, E.C. Bianchi, Application of MQL technique using TiO 2 nanoparticles compared to MQL simultaneous to the grinding wheel cleaning jet, The International Journal of Advanced Manufacturing Technology, 106(5) (2020) 2205-2218. [DOI:10.1007/s00170-019-04760-5]
12. R. de Souza Ruzzi, R.L. de Paiva, R.V. Gelamo, A.R. Machado, R.B. da Silva, Study on grinding of Inconel 625 and 718 alloys with cutting fluid enriched with Multilayer Graphene Platelets, Wear, (2021) 1-11.
13. H. Esmaeili, H. Adibi, S.M. Rezaei, Study on surface integrity and material removal mechanism in eco-friendly grinding of Inconel 718 using numerical and experimental investigations, The International Journal of Advanced Manufacturing Technology, 112(5) (2021) 1797-1818. [DOI:10.1007/s00170-020-06528-8]
14. X. Zhang, R. Jiang, C. Li, Z. Shi, D. Wen, Z. Wang, Z. Shi, J. Jiang, Experimental evaluation of the lubrication performance of MoS 2/TiO 2 nanoparticles for diamond wheel bond in silicon carbide ceramic grinding, The International Journal of Advanced Manufacturing Technology, (2021) 1-9. [DOI:10.1007/s00170-021-06673-8]
15. X. Zhang, C. Li, Y. Zhang, Y. Wang, B. Li, M. Yang, S. Guo, G. Liu, N. Zhang, Lubricating property of MQL grinding of Al2O3/SiC mixed nanofluid with different particle sizes and microtopography analysis by cross-correlation, Precision Engineering, 47 (2017) 532-545. [DOI:10.1016/j.precisioneng.2016.09.016]
16. A. Naskar, B.B. Singh, A. Choudhary, S. Paul, Effect of different grinding fluids applied in minimum quantity cooling-lubrication mode on surface integrity in cBN grinding of Inconel 718, Journal of Manufacturing Processes, 36 (2018) 44-50. [DOI:10.1016/j.jmapro.2018.09.023]
17. R.L. Virdi, S.S. Chatha, H. Singh, Machining performance of Inconel-718 alloy under the influence of nanoparticles based minimum quantity lubrication grinding, Journal of Manufacturing Processes, 59 (2020) 355-365. [DOI:10.1016/j.jmapro.2020.09.056]
18. R.L. Virdi, S.S. Chatha, H. Singh, Performance Evaluation of Inconel 718 under vegetable oils based nanofluids using Minimum Quantity Lubrication Grinding, Materials Today: Proceedings, 33 (2020) 1538-1545. [DOI:10.1016/j.matpr.2020.03.802]
19. R.L. Virdi, S.S. Chatha, H. Singh, Experimental investigations on the tribological and lubrication behaviour of minimum quantity lubrication technique in grinding of Inconel 718 alloy, Tribology International, 153 (2021) 1-7. [DOI:10.1016/j.triboint.2020.106581]
20. R.B. Pavan, A. Venu Gopal, M. Amrita, B.K. Goriparthi, Experimental investigation of graphene nanoplatelets-based minimum quantity lubrication in grinding Inconel 718, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 233(2) (2019) 400-410. [DOI:10.1177/0954405417728311]
21. https://www.specialmetals.com/tech-center/alloys.
22. https://fine-nano.ir/.
23. http://www.amdoilsales.com/products.
24. Y. Wang, C. Li, Y. Zhang, M. Yang, B. Li, L. Dong, J. Wang, Processing characteristics of vegetable oil-based nanofluid MQL for grinding different workpiece materials, International Journal of Precision Engineering and Manufacturing-Green Technology, 5(2) (2018) 327-339. [DOI:10.1007/s40684-018-0035-4]
25. Y. Wang, C. Li, Y. Zhang, B. Li, M. Yang, X. Zhang, S. Guo, G. Liu, Experimental evaluation of the lubrication properties of the wheel/workpiece interface in MQL grinding with different nanofluids, Tribology International, 99 (2016) 198-210. [DOI:10.1016/j.triboint.2016.03.023]
26. Y. Zhang, C. Li, D. Jia, D. Zhang, X. Zhang, Experimental evaluation of the lubrication performance of MoS2/CNT nanofluid for minimal quantity lubrication in Ni-based alloy grinding, International Journal of Machine Tools and Manufacture, 99 (2015) 19-33. [DOI:10.1016/j.ijmachtools.2015.09.003]
27. M. Shabgard, M. Seyedzavvar, M. Mohammadpourfard, Experimental investigation into lubrication properties and mechanism of vegetable-based CuO nanofluid in MQL grinding, The International Journal of Advanced Manufacturing Technology, 92(9) (2017) 3807-3823. [DOI:10.1007/s00170-017-0319-9]
28. M. Shabgard, M. Seyedzavvar, M. Mohammadpourfard, M. Mahboubkhah, Finite difference simulation and experimental investigation: effects of physical synergetic properties of nanoparticles on temperature distribution and surface integrity of workpiece in nanofluid MQL grinding process, The International Journal of Advanced Manufacturing Technology, 95(5) (2018) 2661-2679. [DOI:10.1007/s00170-017-1237-6]
Send email to the article author
| Rights and permissions | |
 |
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. |