مهندسی مکانیک مدرس

مهندسی مکانیک مدرس

بهینه‌سازی عددی- تجربی استحکام اتصالات کامپوزیت پایه اپوکسی تقویت‌شده با الیاف شیشه- فولاد سازه

نوع مقاله : پژوهشی اصیل

نویسندگان
1 مرکز ریزفناوری دارویی، دانشگاه علوم پزشکی تبریز، تبریز، ایران
2 گروه مهندسی مواد، دانشکده مهندسی مکانیک، دانشگاه تبریز، تبریز، ایران
3 گروه مهندسی مکانیک، دانشکده مهندسی، دانشگاه محقق اردبیلی، اردبیل، ایران
چکیده
بروز خرابی و نشتی در لوله‌های انتقال سیال در ایران امری گریزناپذیر است. خرابی منجر به نشتی در خطوط انتقال، بسته به شرایط طراحی و عملیاتی دلایل متفاوتی می‌تواند داشته باشد. از جمله این دلایل می‌توان به آسیب‌های مکانیکی، خوردگی داخلی یا خارجی، خستگی و فشار داخلی بیش‌ازحد مجاز اشاره کرد. در بحث تعمیرات خطوط آسیب‌دیده استراتژی‌های مختلفی برای بازسازی و راه‌اندازی مجدد خط وجود دارد که اهم آنها جایگزینی کل لوله فرسوده، استفاده از کلمپ‌های جوشی و استفاده از وصله‌های کامپوزیتی هستند. در سال‌های اخیر استفاده از وصله‌های کامپوزیتی به‌عنوان روشی کم‌هزینه، دایمی و استاندارد روی جنس‌های مختلف لوله‌ و با کمترین وقفه در کار انتقال مورد پذیرش قرار گرفته است. در پژوهش حاضر با رویکرد بازسازی خطوط فولادی انتقال آب، وصله‌های کامپوزیتی پایه اپوکسی تقویت‌شده با الیاف شیشه به کار گرفته شدند. بهینه‌سازی استحکام چسبندگی وصله‌های کامپوزیتی بر سطح فولاد با بهره‌گیری از روش تاگوچی و آزمون‌های سنجش استحکام چسبندگی کامپوزیت بر سطح فولاد در دو حالت بارگذاری کششی/برشی با سه نوع چسب سیانواکریلات، متااکریلات و اپوکسی در شرایط دمایی و زمانی مختلف پخت چسب صورت پذیرفت. نتایج مطالعات آزمون‌های مکانیکی و تصاویر سطوح شکست حاصل از میکروسکوپ الکترونی روبشی (SEM) بیانگر عملکرد بهتر چسب پایه متااکریلاتی با استحکام چسبندگی مناسب بود.
کلیدواژه‌ها

موضوعات


عنوان مقاله English

Numerical and Experimental Investigation on Boding Strength Optimization of Glass Fibers-Reinforced Epoxy Composites on a Structural Steel Substrate

نویسندگان English

K. Osouli-Bostanabad 1
A. Tutunchi 2
M. Eskandarzade 3
A. Kianvash 2
1 Research Center for Pharmaceutical Nanotechnology, Tabriz University of Medical Sciences, Tabriz, Iran
2 Materials Engineering Department, Mechanical Engineering Faculty, University of Tabriz, Tabriz, Iran
3 Mechanical Engineering Department, Engineering Faculty, University of Mohaghegh Ardabili, Ardabil, Iran
چکیده English

Incidence of breaks and leakages in fluid transportation pipes is a common issue in Iran. Depending on the type of pipes and environmental conditions, the breaks in the pipes may be caused by different factors, including mechanical damages, internal or external corrosions, failures, or applied stresses. In the repair of damaged pipes, there are several strategies for rebuilding and implementing the pipeline, most of which are replacing the entire exhausted pipe, using weld clamps and using composite patches. In recent years, the use of composite patches has been accepted as a low-cost, permanent, and standard method for different pipe sections with the least interruption in transportation. In the present study, the boding strength of glass fibers-reinforced epoxy composite patches on a structural steel substrate were investigated and optimal conditions of achieving enhanced adhesion strength of composite patches on the steel substrate were determined, using the Tagochi method at various curing temperatures and times. In this regard, the tensile and shear strength of epoxy, cyanoacrylate, and methacrylate-based glues as three kinds of appropriate polymers for bonding the epoxy composite on the steel substrates were tested. The mechanical strength measurements and fractured interfaces evaluations using a scanning electron microscopy (SEM) revealed that the methacrylate-based glue has the better adhesion strength to the steel substrate.

کلیدواژه‌ها English

Repair of damaged water pipelines
Fiber-reinforced epoxy composite patches
Optimization of adhesion
Methacrylate-based glues
Mechanical strength
Mohitpour M, Golshan H, Murray A. Pipeline design and construction: A practical approach. 3rd Edition. NewYork: American Society of Mechanical Engineering; 2007. [Link] [DOI:10.1115/1.802574]
Mattos HC, Sampaio RF, Reis JM, Perrut VA. Rehabilitation of corroded steel pipelines with epoxy repair systems. The Journal of Pipeline Engineering. 2008;7(4):295-303. [Link]
Overend M, Jin Q, Watson J. The selection and performance of adhesives for a steel–glass connection. International Journal of Adhesion & Adhesives. 2011;31(7):587-596. [Link] [DOI:10.1016/j.ijadhadh.2011.06.001]
Chen Z, Adams RD, Lucas AB, Da Silva FM. Prediction of crack initiation and propagation of adhesive lap joints using an energy failure criterion. Engineering Fracture Mechanics. 2011;78(6):990-1007. [Link] [DOI:10.1016/j.engfracmech.2010.12.004]
Toutanji H, Dempsey S. Stress modeling of pipelines strengthened with advanced composite materials. Thin-Walled Structures. 2001;39(2):153-165. [Link] [DOI:10.1016/S0263-8231(00)00049-5]
Alexander C, Ozden Ochoa O. Extending onshore pipeline repair to offshore steel risers with carbon-fiber reinforced composites. Composite Structures. 2010;92(2):499-507. [Link] [DOI:10.1016/j.compstruct.2009.08.034]
Duell JM, Wilson JM, Kessler MR. Analysis of a carbon composite overwrap pipeline repair system. International Journal of Pressure Vessels and Piping. 2008;85(11):782-788. [Link] [DOI:10.1016/j.ijpvp.2008.08.001]
Revie RW, Uhlig HH. Corrosion and corrosion control, an introduction to corrosion science and engineering. 4th Edition. Hoboken: John Wiley & Sons; 2008. [Link]
Creton C. Materials Science of Pressure‐Sensitive Adhesives. In: Cahn RW, Haasen P, Kramer EJ, editors. Materials Science and Technology. Hoboken:John Wiley & Sons; 2006. pp. 708-739. [Link] [DOI:10.1002/9783527603978.mst0221]
Baldan A. Adhesion phenomena in bonded joints. International Journal of Adhesion and Adhesives. 2012;38:95-116. [Link] [DOI:10.1016/j.ijadhadh.2012.04.007]
Razavi SMJ, Ayatollahi MR, Nemati Giv A, Khoramishad H. Single lap joints bonded with structural adhesives reinforced with a mixture of silica nanoparticles and multi walled carbon nanotubes. International Journal of Adhesion and Adhesives. 2018;80:76-86. [Link] [DOI:10.1016/j.ijadhadh.2017.10.007]
Balden A. Adhesively bonded joints and repairs in metallic alloy, polymers and composite materials: Adhesives, adhesion theories and surface pretreatment. Journal of Materials Science. 2004;39(1):1-49. [Link] [DOI:10.1023/B:JMSC.0000007726.58758.e4]
13- André NM, Goushegir SM, Scharnagl N, DOS Santos JF, Canto LB, Amancio-Filho ST. Composite surface pre-treatments: Improvement on adhesion mechanisms and mechanical performance of metal–composite friction spot joints with additional film interlayer. The Journal of Adhesion. 2018;94(9):723-742. [Link] [DOI:10.1080/00218464.2017.1378101]
Budhe S, Banea MD, de Barros S, da Silva LFM. An updated review of adhesively bonded joints in composite materials. International Journal of Adhesion and Adhesives. 2017;72:30-42. [Link] [DOI:10.1016/j.ijadhadh.2016.10.010]
Wegman RF, Van Twisk J. Surface preparation techniques for adhesive bonding. 2nd Edition. Amsterdam: Elsevier; 2013. pp. 90-98. [Link]
Tutunchi A, Kamali R, Kianvash A. Steel-epoxy composite joints bonded with nano-TiO2 reinforced structural acrylic adhesive. The Journal of Adhesion. 2015;91(9):663-676. [Link] [DOI:10.1080/00218464.2014.961187]
Tutunchi A, Kamali R, Kianvash A. Effect of Al2O3 nanoparticles on the steel-glass/epoxy composite joint bonded by a two-component structural acrylic adhesive. Soft Materials. 2016;14(1):1-8. [Link] [DOI:10.1080/1539445X.2014.1003269]
Osouli-Bostanabad K, Tutunchi A, Eskandarzade M. The influence of pre-bond surface treatment over the reliability of steel epoxy/glass composites bonded joints. International Journal of Adhesion and Adhesives. 2017;75:145-154. [Link] [DOI:10.1016/j.ijadhadh.2017.03.006]
Chavooshian M, Kamali R, Tutunchi A, Kianvash A. Effect of silicon carbide nanoparticles on the adhesion strength of steel–epoxy composite joints bonded with acrylic adhesives. Journal of Adhesion Science and Technology. 2017;31(4):345-357. [Link] [DOI:10.1080/01694243.2016.1215015]
Zosel A. Adhesive failure and deformation behaviour of polymers. The Journal of Adhesion. 1989;30(1-4):135-149. [Link] [DOI:10.1080/00218468908048202]
Bascom WD, Timmons CO, Jones RL. Apparent interfacial failure in mixed-mode adhesive fracture. Journal of Materials Science. 1975;10(6):1037-1048. [Link] [DOI:10.1007/BF00823223]