Abbasi, E. Formation Control and Path Tracking for a Group of Quadrotors to Carry Out a Suspended Load [Volume 19, Issue 4, 2019, Pages 887-899]
Abbasi, M. Modification of Mechanical Properties of Al6061 Aluminum Alloy Joint Formed Using Friction Stir Welding by Increasing the Cooling Rate and Application of Vibration [Volume 19, Issue 6, 2019, Pages 1551-1558]
Abbasnejad, GH. Determination of Optimal Wrench-closure Configuration of Reconfigurable Cable-driven Parallel Robots to Move on a Given Trajectory [Volume 19, Issue 5, 2019, Pages 1085-1093]
Abdi, H. Dynamic modeling and Designing a dynamic based control algorithm for legged quadruped robot locomotion [Volume 19, Issue 11, 2019, Pages 2635-2644]
Abdolalipouradl, M. The thermodynamic analysis of a novel integrated transcritical CO2 with Kalina 11 cycles from Sabalan geothermal wells [Volume 19, Issue 2, 2019, Pages 335-346]
Abdollahi, M. Identification of Parameters of Spencer Model for a Double-Ended Magnetorheological Damper with Different Spherical Iron Carbonyl Powder Sizes [Volume 19, Issue 5, 2019, Pages 1307-1317]
Abdollahi Haghghi, M. Exergoeconomic Analysis of a Heating and Power Generation Solar System for Using at the Engineering Faculty of Urmia University [Volume 19, Issue 2, 2019, Pages 415-427]
Abdullah, A. WEDM Errors in Straight and Arced Paths: Analysis of Spark Angles on the Roughing and Finishing Stages [Volume 19, Issue 6, 2019, Pages 1519-1528]
Abedi, M. Efficiency Enhancement of Solar Cells of a Sun Pointing Satellite with Design Optimization of Heat Pipes Configuration Using Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 789-800]
Abolbashari, M.H. Multi-Objective Optimal Design and Natural Frequency Analysis of Shape Memory Alloy Composite Beams Using Genetic Algorithm [Volume 19, Issue 10, 2019, Pages 2499-2509]
Abolfazli Esfahsni, J. Numerical Study of Energy Harvesting of Vortex Induced Vibration Phenomenon of Circular Cylinder with Various Sectors at Low Reynolds Number [Volume 19, Issue 7, 2019, Pages 1687-1695]
Abolhasani, Sh. Manufacturing and Investigating Mechanical Properties of Polymeric Composites Reinforced with Natural Fibers [Volume 19, Issue 1, 2019, Pages 75-83]
Abootorabi, M.M. Optimization and Modeling of Plasma Cutting of AISI 309 Stainless Steel by Using Neural Network-Genetic Algorithm Hybrid Model [Volume 19, Issue 10, 2019, Pages 2455-2462]
Abouali, O. Numerical Analysis of the Effect of Train Movement Inside Underground Subway Tunnels on the Air-Exchange Systems by Comparing Fan-Off and Fan-On Conditions [Volume 19, Issue 11, 2019, Pages 2679-2687]
Abouali Shamshiri, M. Nonlinear Model of Thermoelectric Coupling and Experimental and Numerical Analysis of Thermoelectric Generator Setup [Volume 19, Issue 3, 2019, Pages 527-538]
Abouei Mehrizi, A. Evaluation of Young's Modulus and Poisson's Ratios of Diamond Porous Structure for Use in Orthopedic Implant by Finite Element Method [Volume 19, Issue 5, 2019, Pages 1135-1143]
Abravesh, M. Optimum Insulation Thickness Based on Energy Carriers Different Tariffs in Climatic Condition of Tehran [Volume 19, Issue 6, 2019, Pages 1447-1456]
Abyar Firouzabadi, H. WEDM Errors in Straight and Arced Paths: Analysis of Spark Angles on the Roughing and Finishing Stages [Volume 19, Issue 6, 2019, Pages 1519-1528]
Adami, Sh. Analytical and Experimental Study of Sandwich Beams with Flexible Core and Composite Facings Reinforced with Carbon Nanotubes [Volume 19, Issue 4, 2019, Pages 801-813]
Adel, F. Determination of Young's Modulus by Finite Element Model Updating [Volume 19, Issue 8, 2019, Pages 1837-1844]
Adibnazari, S. Effect of Contact Geometry on the Slip Amplitude and Contact Pressure in Fretting Fatigue of a Turbine Blade Root [Volume 19, Issue 10, 2019, Pages 2409-2418]
Afrand, M. Experimental Investigation of the Effect of Cylindrical Protuberance with Different Penetration the Thrust Vector a C-D Nozzle in Supersonic regime [Volume 19, Issue 5, 2019, Pages 1145-1154]
Afrasiab, H. Theoretical and Numerical Investigation of Environmental Effects on Mechanical Behavior of Biodegradable Polymers [Volume 19, Issue 12, 2019, Pages 2837-2846]
Afsari, A. Investigating the Behavior of Aluminum 7075 under the Process of CGP as the Fin of Space Structures [Volume 19, Issue 5, 2019, Pages 1187-1197]
Afshari, B. Numerical Investigation of Cavitation Effect on the Performance of Waterjet Propulsion System by Computational Fluid Dynamics [Volume 19, Issue 7, 2019, Pages 1779-1788]
Afzalian, M. Air Inlet Angle Effects in Swirling Diffuser of UFAD Systems on Micron Particles Pattern Distribution [Volume 19, Issue 12, 2019, Pages 3083-3093]
Aghaei, M. Effect of Cooling System on the Mechanical Properties and Residual Stress of Steel AISI 1045 in Quenching Heat Treatment [Volume 19, Issue 12, 2019, Pages 2979-2986]
Aghaeinezhad, S.M. Individual Pitch Angle Robust Control of a Variable Speed Wind Turbine to Mitigate Mechanical Loads [Volume 19, Issue 4, 2019, Pages 937-945]
Aghaei Togh, R. Numerical Investigation of the Effects of Minor Geometric Changes of the Stator Blade Profiles on the Steady Performance of a High-pressure Gas-turbine [Volume 19, Issue 5, 2019, Pages 1209-1220]
Aghaie, H. 2D Simulation of Red Blood Cell Deformation with Viscoelastic Properties under Ultrasonic Waves [Volume 19, Issue 12, 2019, Pages 3023-3030]
Aghaie-Khafri, M. Study of Damage Propagation and Life Assessment in High Temperature Cyclic Loading [Volume 19, Issue 3, 2019, Pages 731-742]
Aghdoud Chaboki, Y. Thermo-economic Analysis of Waste Heat Recovery by the Use of Engine Exhaust Gases beside the Jacket Cooling Water of the Marine Engine [Volume 19, Issue 3, 2019, Pages 687-696]
Ahmadi, M. Investigation the Effect of Loading Rates on Fracture Toughness of Loading Mode I in Glass / Epoxy Composite Laminates by Acoustic Emission [Volume 19, Issue 12, 2019, Pages 2917-2925]
Ahmadi, R. Discrete Adaptive Sliding Mode Control of an Omnidirectional Mobile Robot Using Time Delay Control Method [Volume 19, Issue 2, 2019, Pages 491-504]
Ajam, H. Numerical Study of Effects of Simultaneous Changes of Geometric Parameters on the Performance of Touss Power Plant Ejector and Selecting Optimal Conditions Using Taguchi Method [Volume 19, Issue 3, 2019, Pages 621-629]
Akbari, Javad Manufacturing and Investigating Mechanical Properties of Polymeric Composites Reinforced with Natural Fibers [Volume 19, Issue 1, 2019, Pages 75-83]
Akbari, M. Designing l_1 norm Based Sliding Mode Controller For Implementing in Hybrid Model of Gas Turbine [Volume 19, Issue 10, 2019, Pages 2339-2350]
Akbaripanah, F. Effect of Multidirectional Forging on Microstructures and Mechanical Properties of Nano-SiC Reinforced AZ31 Nanocomposites [Volume 19, Issue 4, 2019, Pages 981-989]
Akbari Paydar, M. Optimum Insulation Thickness Based on Energy Carriers Different Tariffs in Climatic Condition of Tehran [Volume 19, Issue 6, 2019, Pages 1447-1456]
Akbarzadeh, A. Effect of Number of Blades on Performance of an Axial Gas Turbine [Volume 19, Issue 12, 2019, Pages 2907-2916]
Akrami Nia, E. Investigating the Static Deformation and Instability Voltage of Viscoelastic Curved Microbeam [Volume 19, Issue 10, 2019, Pages 2375-2385]
Alaei, M.H. Optimization of Injection Parameters in Metal Injection Molding of 4605 Low Alloy Steel [Volume 19, Issue 5, 2019, Pages 1199-1208]
Alavi nia, A. High Velocity Impact on Sandwich Panels with Graded Foam-cored and Aluminum Face-sheet: Numerical and Experimental Assessment [Volume 19, Issue 4, 2019, Pages 1039-1047]
Aligholami, M. Investigation of Geometrical Parameters and Hydrophobic Surfaces on the Performance of Solar Chimney Power Plant [Volume 19, Issue 10, 2019, Pages 2397-2407]
Alijabbari, M. Analysis of Instability on the Boundary of the Inhomogeneous Fluids with Varying Densities in the Presence of Incident Shock [Volume 19, Issue 3, 2019, Pages 577-585]
Alimoradi, H. Numerical Simulation of the Effects of Surface Roughness on Nucleation Site Density of Nanofluid Boiling [Volume 19, Issue 7, 2019, Pages 1613-1622]
Aliparast, P. Vancomycin Adsorption on Microcantilever Based on Molecular Dynamics Simulation [Volume 19, Issue 10, 2019, Pages 2481-2489]
Alipour, A. Modeling and Simulation of Fuel Sloshing in Tank by Pendulum Model [Volume 19, Issue 8, 2019, Pages 2001-2011]
Alisadeghi, H. Numerical Simulation and Parametric Study of an Oscillating Twin-Wing Wind Generator [Volume 19, Issue 5, 2019, Pages 1115-1125]
Aliyari Shooredeli, M. Sensitivity Analysis and Design of Univariate Alarm System Based on Delay Timer Considering Measurement Errors [Volume 19, Issue 5, 2019, Pages 1155-1165]
Alizadeh, M. Analytical Tow-Dimensional Modeling of Blood Flow in a Balloon with Periodic Inflation and Deflation; Application in Intra- and Extra-Aortic Cardiac Assist Devices [Volume 19, Issue 3, 2019, Pages 569-576]
Ameri, M. Direct Steam Generation Solar Power Plant in The Two Pressures Cycle [Volume 19, Issue 1, 2019, Pages 11-19]
Amidpour, M. Thermodynamic, Economic and Case Study of Synthesis Gas Using the Biomass Gasification Reactor in Distributed Generation Systems [Volume 19, Issue 6, 2019, Pages 1417-1428]
Amidpour, M. Waste Heat Recovery Rankine Cycle Based System for Heavy Duty Trucks [Volume 19, Issue 7, 2019, Pages 1633-1643]
Amini, R. Experimental Relationship of Yield and Tensile Strengths with Hardness in High Strength APIX70 Steel Pipes [Volume 19, Issue 1, 2019, Pages 85-93]
Amini, S. Invention of a New Ultrasonic Horn in 3D Ultrasonic Vibration Assisted Turning [Volume 19, Issue 8, 2019, Pages 1845-1854]
Aminzadeh, A. Experimental Study of Weld Line Displacement and Drawing Depth in TWBs Steel Sheets Manufactured by Laser and Friction Stir Welding [Volume 19, Issue 9, 2019, Pages 2183-2192]
AmirAhmadi, S. Calculating residual stresses by measured released strains using different linear and nonlinear approximations [Volume 19, Issue 3, 2019, Pages 609-620]
Andakhshideh, A. Investigating the Crack Propagation at the Surface of the Composite Patch Bonding to the Steel Substrate [Volume 19, Issue 8, 2019, Pages 1897-1906]
Andakhshideh, A. Nonlinear Dynamics Control and Analysis of Atomic Force Microscope Based On Nonlocal Model [Volume 19, Issue 12, 2019, Pages 2987-2997]
Ansari, M.R. A Theoretical Model for Evaporation of Leidenfrost Drop for Prediction of Vapor Layer Thickness under the Drop [Volume 19, Issue 4, 2019, Pages 969-979]
Ansari, M.R. Behaviour of Dielectric Fluid Droplet under the Influence of Uniform Magnetic Field [Volume 19, Issue 12, 2019, Pages 2847-2856]
Ansarian, I. Microstructure, Mechanical, and Electrical Properties of Cu-30Zn Alloys Produced by Multi-Directional Forging [Volume 19, Issue 8, 2019, Pages 1943-1952]
Arabi, H. Investigation and Modelling the Flow Behavior of Fe-17Cr-7Ni Semi-Austenitic Precipitation Hardening Stainless Steel Using the Hyperbolic Sine Constitutive Equation [Volume 19, Issue 6, 2019, Pages 1439-1445]
Araghi, H. Study of the Strain - Stress Effect on Ferroelectric Behaviors of PbTiO3 [Volume 19, Issue 9, 2019, Pages 2149-2154]
Ardekani, M.A. Experimental Investigation on Negative Values of Yaw Sensitivity Coefficient for Hot Wire Anemometer Sensor in Two-dimensional Flow Measurement [Volume 19, Issue 5, 2019, Pages 1275-1282]
Arefkhani, H. Nonlinear Dynamic Inversion Controller Design for a Satellite, Considering the Dynamics of Magnetorquers [Volume 19, Issue 8, 2019, Pages 1875-1887]
Arvahi, M. Interfacial Tension Measurement Using Microfluidics [Volume 19, Issue 4, 2019, Pages 911-918]
Asgari, B. Calculating residual stresses by measured released strains using different linear and nonlinear approximations [Volume 19, Issue 3, 2019, Pages 609-620]
Asgari, M. Nonlinear Model of Thermoelectric Coupling and Experimental and Numerical Analysis of Thermoelectric Generator Setup [Volume 19, Issue 3, 2019, Pages 527-538]
Asgari, M. Mechanical Properties of Functionally Graded Porous Biomaterials for Application in Prosthesis Replacement Using Analytical and Numerical Solution [Volume 19, Issue 11, 2019, Pages 2717-2727]
Asghari, M. Design and Analysis of Axisymmetric Supersonic Inlet at Mach 3 [Volume 19, Issue 10, 2019, Pages 2543-2550]
Ashjaee, M. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Ashouri, R. Analysis of Instability on the Boundary of the Inhomogeneous Fluids with Varying Densities in the Presence of Incident Shock [Volume 19, Issue 3, 2019, Pages 577-585]
Ashrafi, A. The Use of Internal Mechanical Insert to Prevent Wrinkling Defects in T-joint Hydroforming Process [Volume 19, Issue 8, 2019, Pages 1989-2000]
Ashrafnia, S.A. Calculating the Size-dependent Surface Energy of Metallic Spherical Nanoparticles and Nanocavities Using Molecular Dynamics [Volume 19, Issue 4, 2019, Pages 1001-1007]
Atashkari, K. A Parametric Study on Optical Performance of a Multi-Tubular Solar Reactor by Monte-Carlo ray Tracing Method [Volume 19, Issue 3, 2019, Pages 643-653]
Atashkari, K. Simulation and Comparison of the Effect of Oxidizing Gas and Different Devolatilization Models in an Entrained-Flow Coal Gasifier [Volume 19, Issue 12, 2019, Pages 3071-3082]
Azadian, A. Discrete-Time Control of a Nonlinear System with Integrating the Integral Terminal Sliding Mode and Model Predictive Control [Volume 19, Issue 11, 2019, Pages 2697-2704]
Azadi Tabar, M. Experimental Study of Surfapore Nanofluid Effect on Surface Free Energy of Calcite Rock [Volume 19, Issue 3, 2019, Pages 709-718]
Azarkish, H. Design of a Capillary-Driven Microfluidic Cooling System Using Non-Uniform Cross Section Microchannel [Volume 19, Issue 6, 2019, Pages 1319-1325]
Azdast, T. A Review on Principles and Fundamentals of Fabrication of Polymeric Foams in Regards to Increasing Cell Density/ Reducing Cell Size [Volume 19, Issue 1, 2019, Pages 211-222]
Azdast, T. Optimization of solid and radiation thermal conductivity of polymeric foams using response surface method based on a novel theoretical model [Volume 19, Issue 9, 2019, Pages 2165-2173]
Azdast, T. Estimating the Thermal Conductivity of Polymeric Foams Based on a Theoretical Model Using Cell Size and Foam Density [Volume 19, Issue 9, 2019, Pages 2273-2283]
Azhdary Moghaddam, M. Strengthening Defected Dam Gates under Cavitation Vibration Using CFRP [Volume 19, Issue 4, 2019, Pages 825-831]
Azizzadeh, T. Modeling and Experimental Investigation of Pulsed Eddy Current and Magnetic Saturation for Testing of Ferromagnetic Metals with Sub-surface Pitting [Volume 19, Issue 1, 2019, Pages 143-149]
Azmoun, M. Mechanical Improvement, Simulation, and Implementation of a Visual Servoing Position Controller of a 4-DOF Delta Parallel Robot [Volume 19, Issue 1, 2019, Pages 115-123]
B
Babaee, D. Study of Ratcheting Behavior of 304L Stainless Steel Branch Pipes by Using Chaboche and Combined Hardening Models [Volume 19, Issue 9, 2019, Pages 2193-2201]
Babaei, A.H. Numerical Investigation of the Effects of Minor Geometric Changes of the Stator Blade Profiles on the Steady Performance of a High-pressure Gas-turbine [Volume 19, Issue 5, 2019, Pages 1209-1220]
Babaeyan, M.R. Experimental investigation of the penetration effects of opposite dual protuberances on thrust vector of a supersonic C-D nozzle [Volume 19, Issue 7, 2019, Pages 1741-1750]
Babaie, Z. Investigation of Aerodynamic and Heat Transfer Performance of Cylinders Using Plasma Actuators [Volume 19, Issue 9, 2019, Pages 2111-2120]
Babazadeh Mehrababni, E. Investigating the Effect of Different Sensors on the Observer Performance in Vehicle Suspension System Based on the Observable Degree Analysis [Volume 19, Issue 7, 2019, Pages 1675-1684]
Badiei, D. Development of Boeing-Vertol Dynamic Stall Model Considering Unsteady Flow Effects [Volume 19, Issue 10, 2019, Pages 2559-2569]
Badri, M.A. Implementation of rigid solid boundaries to the Vorticity-Stream function formulation of incompressible Navier-Stokes equations by time dilation [Volume 19, Issue 5, 2019, Pages 1241-1252]
Badri-kouhi, E. Effect of Contact Geometry on the Slip Amplitude and Contact Pressure in Fretting Fatigue of a Turbine Blade Root [Volume 19, Issue 10, 2019, Pages 2409-2418]
Bagheri, A. A New Hybrid Intelligent Technique Based on Improving the Compensation Distance Evaluation Technique and Support Vector Machine for Bearing Fault Diagnosis [Volume 19, Issue 4, 2019, Pages 865-875]
Bagheri, Mohammad Reza Pareto Optimization of a Three-Dimensional Full Vehicle Suspension Model Using Multi-Objective Genetic Algorithm [Volume 19, Issue 8, 2019, Pages 1971-1978]
Bagheri-Esfe, H. Effect of Using Different Gases in Multi-glazed Windows to Reduce Building Heat Losses [Volume 19, Issue 6, 2019, Pages 1409-1416]
Bagherpour, H. Thermal Analysis of Laser Welding in Joint of Stainless Steel to Low Carbon Steel Using Finite Element Method (FEM) [Volume 19, Issue 6, 2019, Pages 1475-1482]
Baghshahi, S. Improving the Mechanical Properties of Mn-rich Al-4Ni-4Mn Alloy by Increasing the Solidification Rate and Friction Stir Processing [Volume 19, Issue 9, 2019, Pages 2175-2182]
Bahrami, A. Nonlinear Dynamics and Chaotic Behavior in an Oscillator Connected to Shape Memory Alloy [Volume 19, Issue 1, 2019, Pages 95-104]
Bahrami, A. Investigation of Mixed Convection Flow in a Lid-driven Cavity Filled with Micropolar Nanofluid [Volume 19, Issue 6, 2019, Pages 1483-1494]
Bakhshan, Y. Investigating the Behavior of Aluminum 7075 under the Process of CGP as the Fin of Space Structures [Volume 19, Issue 5, 2019, Pages 1187-1197]
Bakhshi Jooybari, M. Determination of Process Window of St12 Steel Sheet in Single Point Incremental Forming of a Truncated Pyramid by Experimental Method [Volume 19, Issue 10, 2019, Pages 2551-2558]
Bakhtiari, E. Effects of Oscillation Parameters of a Wind Turbine Airfoil with Slip Velocities on Aerodynamic Loads [Volume 19, Issue 9, 2019, Pages 2093-2104]
Bakhtiari far, M. Numerical Study of Aerodynamic Behavior of a Plunging Airfoil in Ground Effect [Volume 19, Issue 3, 2019, Pages 753-763]
Barati, E. Numerical Study of Energy Harvesting of Vortex Induced Vibration Phenomenon of Circular Cylinder with Various Sectors at Low Reynolds Number [Volume 19, Issue 7, 2019, Pages 1687-1695]
Barghi Jahromi, M.S. Effect of Forced Convection and PCM Materials on an Indirect Solar Dryer Equipped with Evacuated Heat Pipe Collector [Volume 19, Issue 11, 2019, Pages 2607-2614]
Bathaee, S.H. Second Phase of Nanomanipulation of Particles by Atomic Force Microscopy Using Coulomb, HK, and LuGre Friction Models [Volume 19, Issue 1, 2019, Pages 181-190]
Bayat, Gh.R. Comparison of Li-Ion Battery State of Charge Prediction by Artificial Neural Network and Adaptive Neuro Fuzzy Inference System [Volume 19, Issue 1, 2019, Pages 43-52]
Beigzadeh, B. Design New Cable System to Drive Exoskeleton Fingers for Rehabilitation [Volume 19, Issue 1, 2019, Pages 201-209]
Beigzadeh, B. Pedestrian tracking by means of inertial navigation system [Volume 19, Issue 2, 2019, Pages 407-414]
Beigzadeh, B. Heart Rate Measurement with Imaging Photoplethysmography Signals Using Smart Phone [Volume 19, Issue 7, 2019, Pages 1751-1757]
Beygi, E. Determination of Young's Modulus by Finite Element Model Updating [Volume 19, Issue 8, 2019, Pages 1837-1844]
Binazadeh, T. Distributed Adaptive Robust Controller Design for Consensus in Multi-Agent System Including Robot Arms with Actuator Saturation Constraint [Volume 19, Issue 7, 2019, Pages 1759-1766]
Binesh, B. Experimental Study and Simulation of Semi-Constrained Groove Pressing of Interstitial Free Steel Sheet [Volume 19, Issue 11, 2019, Pages 2781-2791]
Bolandi Kashani, A.H. Numerical Simulation of Droplet Falling and Positioning on Surface Using Multiphase Lattice Boltzmann Model [Volume 19, Issue 1, 2019, Pages 171-179]
Borhani, E. New Strategy to Simultaneous Increase in Strength and Electrical Conductivity of UFG Copper Strip Fabricated via Accumulative Roll Bonding- Cold Roll Bonding [Volume 19, Issue 9, 2019, Pages 2085-2092]
Borhanpanah, M. Developing an Aero-Elastic Model of a Full Aircraft to Study the Effect of Flexibility on its Flight Dynamics Derivatives [Volume 19, Issue 10, 2019, Pages 2511-2521]
Bourbour, A.R. Joint-Space Position Control of a Deployable Cable Driven Robot in Joint Space Using Force Sensors and Actuator Encoders [Volume 19, Issue 11, 2019, Pages 2615-2625]
C
Chalangari Juybari, H. Modeling and Experimental Evaluation of Stiffness of a Linear Decoupled 3 Degree of Freedom Parallel Robot [Volume 19, Issue 6, 2019, Pages 1385-1396]
Chamani, H.R. Numerical Simulation of the Boiling Phenomenon in Improving the Cooling of a Heavy-Duty Diesel Engine with Natural Gas [Volume 19, Issue 2, 2019, Pages 363-373]
Chaparian, Y. Investigation of Effect of Structural Parameters on High Velocity Impact Resistance of Fiber Metal Laminates [Volume 19, Issue 6, 2019, Pages 1529-1538]
Cheraghi, N. Free Vibration Analysis of Functionally Graded Magneto-electro-elastic Plates Resting on Elastic Foundations with Considering Interfacial Imperfections [Volume 19, Issue 3, 2019, Pages 655-663]
Chini, S.F. Numerical Analysis of Water Injection Effect on NOx Reduction of MGT-40 Gas Turbine [Volume 19, Issue 2, 2019, Pages 397-405]
Chitsaz, Iman Feasibility Study of Partially Stratified Charge Mixture Formation and Its Effects on CNG Direct Injection Engine [Volume 19, Issue 10, 2019, Pages 2329-2338]
Chitsaz Khoyi, A. Exergoeconomic Analysis of a Heating and Power Generation Solar System for Using at the Engineering Faculty of Urmia University [Volume 19, Issue 2, 2019, Pages 415-427]
D
Dabirpour, V. Numerical Investigation of Convection around Heated Circular Cylinder Wrapped with Bi-Disperse Porous Medium in Channel [Volume 19, Issue 3, 2019, Pages 539-548]
Dadash Zadeh, B. Modeling and Experimental Evaluation of Stiffness of a Linear Decoupled 3 Degree of Freedom Parallel Robot [Volume 19, Issue 6, 2019, Pages 1385-1396]
Dadgar fard, A. Self-Activated Acoustical Swimmer and Functionality Comparison with Equivalent Hydrodynamic Swimmers: Spherical Model at Low Reynolds Number Condition [Volume 19, Issue 11, 2019, Pages 2581-2588]
Dalilsafaei, S. Inference System Based on Fuzzy Clustering to Display the Flow Field Changes in the Rotor Outlet of Centrifugal Turbomachinery [Volume 19, Issue 6, 2019, Pages 1495-1505]
Danandeh Oskuei, H. Design, Construction and Analysis of the Gamma-Type Solar Stirling Engine by Parabolic Solar Collector [Volume 19, Issue 9, 2019, Pages 2255-2262]
Danesh, M. Formation Control and Path Tracking for a Group of Quadrotors to Carry Out a Suspended Load [Volume 19, Issue 4, 2019, Pages 887-899]
Daneshgar, P. Modeling and Simulation of Fuel Sloshing in Tank by Pendulum Model [Volume 19, Issue 8, 2019, Pages 2001-2011]
Daneshmehr, A. Numerical Modeling of Concentric Left Ventricular Hypertrophy of the Human Heart [Volume 19, Issue 10, 2019, Pages 2491-2498]
Darabi, P. Analytical Solution for Vibration Analysis of Piezoelectric Shallow Spherical Sensors and Actuators [Volume 19, Issue 3, 2019, Pages 597-608]
Dardel, M. 1D- 1D Modeling of High Pressure PEM Electrolyzers for Hydrogen Production [Volume 19, Issue 7, 2019, Pages 1663-1674]
Darvishi, M.M. Estimating the Thermal Conductivity of Polymeric Foams Based on a Theoretical Model Using Cell Size and Foam Density [Volume 19, Issue 9, 2019, Pages 2273-2283]
Dashti Rahmatabadi, A. Analysis of Static Performance of Noncircular Lobed Journal Bearings with Lubricants Containing TiO2 Nanoparticles Using Couple Stress Fluid Model [Volume 19, Issue 1, 2019, Pages 151-157]
Dashti Rahmatabadi, A. Effect of Shell Surface Texture Geometry on the Steady State Performance Indexes of Hydrodynamic Journal Bearings [Volume 19, Issue 10, 2019, Pages 2443-2453]
Dastjerdi, M.M. Fast and Precise Estimation of Displacement and Strain Fields in Elastography Imaging Technique [Volume 19, Issue 2, 2019, Pages 303-315]
Davarpanah, E. Numerical Study on the Impact of DC Electric Field on Fouling Characteristics of Cross-Flow Filtration [Volume 19, Issue 5, 2019, Pages 1061-1073]
Davodi, A. Modeling of Fuel Sloshing in a Spacecraft and Control it by Active Control Method Using Nonlinear Control [Volume 19, Issue 9, 2019, Pages 2121-2128]
Dehghan, A.A. Analysis of Static Performance of Noncircular Lobed Journal Bearings with Lubricants Containing TiO2 Nanoparticles Using Couple Stress Fluid Model [Volume 19, Issue 1, 2019, Pages 151-157]
Dehghani Firouzabadi, R. Flutter of a Circular Cylindrical Shell Subjected to Supersonic External Flow by Considering Internal Fluid Effects through a Novel Formulation [Volume 19, Issue 6, 2019, Pages 1355-1362]
Dehghani Firouz-Abadi, R. Developing an Aero-Elastic Model of a Full Aircraft to Study the Effect of Flexibility on its Flight Dynamics Derivatives [Volume 19, Issue 10, 2019, Pages 2511-2521]
Deilami Azodi, H. Investigation on Forming Limit of Aluminum Sheet in Warm Incremental Forming Process [Volume 19, Issue 2, 2019, Pages 259-268]
Doniavi, A. Optimization of solid and radiation thermal conductivity of polymeric foams using response surface method based on a novel theoretical model [Volume 19, Issue 9, 2019, Pages 2165-2173]
Doniavi, A. Estimating the Thermal Conductivity of Polymeric Foams Based on a Theoretical Model Using Cell Size and Foam Density [Volume 19, Issue 9, 2019, Pages 2273-2283]
E
Ebrahimi dehshalie, M. Optimal Control Algorithm Design for the Microfluidic Channel Network Droplet Generation with Output Feedback Delay [Volume 19, Issue 7, 2019, Pages 1585-1590]
Ebrahimzadegan, A. Experimental Study of the Water Absorption and Fatigue Life of PMMA/MWCNTs Nanocomposites [Volume 19, Issue 7, 2019, Pages 1819-1825]
Eimani Kalehsar, H. Numerical Investigation of Aeroelastic Behavior of Tall Buildings Considering Wind-Structure Interaction [Volume 19, Issue 3, 2019, Pages 719-730]
Ekhteraei Toussi, H. Investigating the Static Deformation and Instability Voltage of Viscoelastic Curved Microbeam [Volume 19, Issue 10, 2019, Pages 2375-2385]
Elmkhah, H. Numerical and Experimental Investigations of Mechanical Behavior of Hard TiAlN Nanostructured Coatings Applied by PVD on HSS Substrate [Volume 19, Issue 12, 2019, Pages 3063-3069]
Elyasi, M. Predicting Tearing Force for Square Cup Deep Drawing Process by Dimensionless Analysis of the Effective Geometric Parameters [Volume 19, Issue 10, 2019, Pages 2419-2430]
Esbati Lavasani, R. Derivation and Aeroelastic Analysis of a Rotating Airfoil Using Unsteady Loewy Aerodynamic and Flutter Suppression by PID Controller [Volume 19, Issue 6, 2019, Pages 1347-1354]
Eskandarzade, M. Numerical and Experimental Investigation on Boding Strength Optimization of Glass Fibers-Reinforced Epoxy Composites on a Structural Steel Substrate [Volume 19, Issue 2, 2019, Pages 387-396]
Esmaili, Q. 1D- 1D Modeling of High Pressure PEM Electrolyzers for Hydrogen Production [Volume 19, Issue 7, 2019, Pages 1663-1674]
Etefagh, M.M. Experimental Study of Damage Detection in Beam Using Dynamic Excitation System and Wavelet Packet Transform and Energy Rate Index [Volume 19, Issue 7, 2019, Pages 1655-1662]
Etemadi, E. Free Vibration Analysis of Functionally Graded Magneto-electro-elastic Plates Resting on Elastic Foundations with Considering Interfacial Imperfections [Volume 19, Issue 3, 2019, Pages 655-663]
Ettelaei, M. Experimental Study on the Functionally Graded Ni-P-Al2O3 Coating Created on AA 5xxx Series for Wear Resistance Improvement by Pulse-Electrodeposition Method [Volume 19, Issue 2, 2019, Pages 293-302]
Eungkee Lee, R. Optimization of solid and radiation thermal conductivity of polymeric foams using response surface method based on a novel theoretical model [Volume 19, Issue 9, 2019, Pages 2165-2173]
F
Fada, H. Analysis of Transient Tip-Sample Interactions in High Speed Tapping Mode Atomic Force Microscopy with the Purpose of Damage Prevention [Volume 19, Issue 8, 2019, Pages 1827-1836]
Fadaee, M. Analytical Solution for Vibration Analysis of Piezoelectric Shallow Spherical Sensors and Actuators [Volume 19, Issue 3, 2019, Pages 597-608]
Faezian, A. Modeling of an Evacuated Tube Solar Cooker and Investigation of Weather Parameters Effect [Volume 19, Issue 7, 2019, Pages 1573-1584]
Fakoor, M. Optimal Layout Design of a Satellite Considering Thermal Control Subsystem Constraints [Volume 19, Issue 8, 2019, Pages 1959-1969]
Fakoor, M. Matrix Reinforcement Coefficients Models for Fracture Investigation of Orthotropic Materials [Volume 19, Issue 11, 2019, Pages 2811-2822]
Falahati Nodeh, T. Investigating the Effect of Different Sensors on the Observer Performance in Vehicle Suspension System Based on the Observable Degree Analysis [Volume 19, Issue 7, 2019, Pages 1675-1684]
Fallah, A. Fast and Precise Estimation of Displacement and Strain Fields in Elastography Imaging Technique [Volume 19, Issue 2, 2019, Pages 303-315]
Fallah, F. Manufacturing and Investigating Mechanical Properties of Polymeric Composites Reinforced with Natural Fibers [Volume 19, Issue 1, 2019, Pages 75-83]
Fallah, F. Study of the stability of atherosclerotic arteries using fluid-structure interaction [Volume 19, Issue 3, 2019, Pages 677-686]
Fallah, M. Identification of Dynamic Model for an Active Boring Bar [Volume 19, Issue 8, 2019, Pages 1917-1928]
Fanaee, S.A. Analysis of the Fluid-Thermal Regime with the Developed Brinkman Model in a Porous Coil for Solar Energy Application [Volume 19, Issue 4, 2019, Pages 855-863]
Farahani, M. Characterization of the Plastic and Elastic Properties of Aluminum Sheet Produced by CRB Process via DIC Method [Volume 19, Issue 2, 2019, Pages 505-513]
Farahani, M. Analytic model for investigation of effect of temperature change on residual stress and curvature of symmetric and un-symmetric composite laminates [Volume 19, Issue 9, 2019, Pages 2155-2164]
Farahani, M.R. Simulation of the Residual Stresses Distribution in Girth Weld of Gas Transmission Pipeline [Volume 19, Issue 1, 2019, Pages 223-228]
Farahani, M.R. Analysis of Variance of Residual Stress Distribution in Girth Welding of High Strength Low Alloy Steel Gas Pipeline [Volume 19, Issue 7, 2019, Pages 1789-1795]
Faraji, H. The Use of Internal Mechanical Insert to Prevent Wrinkling Defects in T-joint Hydroforming Process [Volume 19, Issue 8, 2019, Pages 1989-2000]
Faraji Kheyrabadi, M. Numerical Investigation of Ambient Temperature and Actual Impactor Plates Effects on Its Efficiency [Volume 19, Issue 6, 2019, Pages 1327-1335]
Faramarzi, S. Experimental Investigation of Dust Influences on the Airplanes Sound Pressure Emission [Volume 19, Issue 4, 2019, Pages 815-823]
Faramarzian Haghighi, A. Simulation of Mechanical Behavior and Construction of Regular PLA Scaffolds [Volume 19, Issue 8, 2019, Pages 1953-1958]
Farhani, Foad Experimental Investigation on Negative Values of Yaw Sensitivity Coefficient for Hot Wire Anemometer Sensor in Two-dimensional Flow Measurement [Volume 19, Issue 5, 2019, Pages 1275-1282]
Farhat, J. Pedestrian tracking by means of inertial navigation system [Volume 19, Issue 2, 2019, Pages 407-414]
Faroughi, Sh. Homogenization of Porous Shape Memory Alloys Using Monte Carlo Technique [Volume 19, Issue 8, 2019, Pages 2013-2022]
Farrokhi, M. Vision-Based Model Predictive Control of Wheeled Mobile Robot [Volume 19, Issue 7, 2019, Pages 1767-1777]
Farsad, S. Experimental Investigation on Negative Values of Yaw Sensitivity Coefficient for Hot Wire Anemometer Sensor in Two-dimensional Flow Measurement [Volume 19, Issue 5, 2019, Pages 1275-1282]
Farzaneh-Gord, M. Optimization of Geometric Dimensions of Fire Tube and Heat Coil Used in City Gate Stations Heaters [Volume 19, Issue 5, 2019, Pages 1103-1114]
Fatehi Sichani, F. Investigation of Bonding Strength of Steel/Stainless Steel Bimetallic Rod [Volume 19, Issue 1, 2019, Pages 105-113]
Fathali, M. Investigating the Effect of Surface Roughness on Efficiency of Large Wind Farms by Large Eddy Simulation [Volume 19, Issue 10, 2019, Pages 2367-2374]
Fathollahi, S. Parametric Study of the Effects of Ice Accretion on the Aerodynamic Performance of NACA0012 Airfoil Using FENSAP-ICE [Volume 19, Issue 9, 2019, Pages 2285-2297]
Fatouraee, N. Numerical Evaluation of the Effect of Percentage and Location of Stenosis on the Hemodynamic Bifurcation of the Left Coronary Artery [Volume 19, Issue 3, 2019, Pages 743-752]
Fazeli Veisari, S. Nonlinear Viscoelastic Formulation of Spinal Ligament [Volume 19, Issue 9, 2019, Pages 2227-2234]
Fazel Zarandi, M.H Inference System Based on Fuzzy Clustering to Display the Flow Field Changes in the Rotor Outlet of Centrifugal Turbomachinery [Volume 19, Issue 6, 2019, Pages 1495-1505]
Fesharakifard, R. Control Analysis of an Auxiliary Mechanism for Trajectory Tracking of Planar Seams in Robotic Welding [Volume 19, Issue 4, 2019, Pages 1021-1028]
Fotuhi, A.R. Longitudinal Free Vibrations of a Rod with Variable Cross-Section Undergoing Finite Strain [Volume 19, Issue 2, 2019, Pages 429-437]
G
Gandjalikhan Nassab, S.A.R. Numerical analysis of inclined double pane windows with considering combined natural convection and radiation in filling gas [Volume 19, Issue 9, 2019, Pages 2235-2245]
Garshasbi, M. Numerical Analysis of Flow Separation Control on a BWB Drone Using a Vortex Generator [Volume 19, Issue 2, 2019, Pages 447-456]
Ghaderi, H. Evaluation of the Heat Transfer Coefficient of Multi-walled Boron Nitride Nanotubes [Volume 19, Issue 9, 2019, Pages 2105-2110]
Ghaebi, H. Energy and Exergy Analysis and Optimization of a Multigeneration System by Coupling of GT-MHR Reactor, Absorption Refrigeration, Steam Reforming, and HDH Desalination Cycles [Volume 19, Issue 3, 2019, Pages 631-642]
Ghaedamini Harouni, A.R. Multi-Disciplinary Multi-Objective Shape Optimization of Orion Type Re-entry Capsule [Volume 19, Issue 3, 2019, Pages 665-675]
Ghafarian Eidgahi Moghadam, M. Investigation of Magneto-Rheological Fluid Properties inside MR Damper by Use of Dissipative Particle Dynamics Method [Volume 19, Issue 4, 2019, Pages 991-1000]
Ghafarirad, H. Control Analysis of an Auxiliary Mechanism for Trajectory Tracking of Planar Seams in Robotic Welding [Volume 19, Issue 4, 2019, Pages 1021-1028]
Ghafarirad, H. Hysteretic Constitutive Equations Based Continuous Dynamic Modeling of Bending Piezoelectric Actuators [Volume 19, Issue 5, 2019, Pages 1229-1239]
Ghafarirad, H. Kinematic Modelling of Origami-Inspired Continuum Robotic Arm by Constant-Curvature Elements [Volume 19, Issue 11, 2019, Pages 2729-2735]
Ghaffari, H. Modeling and Simulation of Nonlinear Dynamics of Helicopter Rotor Flapping Considering Offset, Blade Weight Moment and Frequency of Flapping [Volume 19, Issue 10, 2019, Pages 2523-2534]
Ghajar, R. Determination of Stress Intensity Factor for Unequal Cracks Emanating from a Quasi-square Hole under Shear [Volume 19, Issue 1, 2019, Pages 21-28]
Ghanbari, F. Design of the Bistable Compliant Four-bar Linkage with Changing the Position of the Flexible Limb [Volume 19, Issue 8, 2019, Pages 2047-2055]
Ghannadi, M. Experimental Analysis of Micro- Nano Bubble Formation inside Venturi Tube with High Speed Photography and Image Processing [Volume 19, Issue 12, 2019, Pages 3039-3049]
Gharehkhani, S. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Ghasemi, A. Calculating residual stresses by measured released strains using different linear and nonlinear approximations [Volume 19, Issue 3, 2019, Pages 609-620]
Ghasemi, A. Evaluation of the Heat Transfer Coefficient of Multi-walled Boron Nitride Nanotubes [Volume 19, Issue 9, 2019, Pages 2105-2110]
Ghasemi, A.R Analysis of Circular Hole and Thermal Cycle Effects on the Mechanical Properties in Multi-Layer Polymer Composite Reinforced with Nanoparticles [Volume 19, Issue 1, 2019, Pages 229-236]
Ghasemi, P. Analytical and Experimental Study of Sandwich Beams with Flexible Core and Composite Facings Reinforced with Carbon Nanotubes [Volume 19, Issue 4, 2019, Pages 801-813]
Ghasemi Varzaneh, M. Design of a basic module for angular motion of spherical joints using the actuators of shape memory alloys and magnetic stabilization system [Volume 19, Issue 2, 2019, Pages 375-386]
Ghasemlooy, S. Numerical Study of the Effect of Flow Suction on the Reduction of Acoustic Noise Due to the Flow on a Three-Dimensional Cylinder [Volume 19, Issue 5, 2019, Pages 1049-1059]
Ghauori, M. Stress Analysis and Feasibility of Fabrication of Laminar Ring [Volume 19, Issue 8, 2019, Pages 2039-2046]
Ghavami Gargari, S. Energy and Exergy Analysis and Optimization of a Multigeneration System by Coupling of GT-MHR Reactor, Absorption Refrigeration, Steam Reforming, and HDH Desalination Cycles [Volume 19, Issue 3, 2019, Pages 631-642]
Ghavami Namin, B. Introduction, Simulation and Experimental Investigation of a Planar Positioner Based on Permanent Magnet Linear Synchronous Motor Technology [Volume 19, Issue 11, 2019, Pages 2803-2810]
Ghayour, M. Formation Control and Path Tracking for a Group of Quadrotors to Carry Out a Suspended Load [Volume 19, Issue 4, 2019, Pages 887-899]
Ghayour, M. Effect of Fluid and Size on the Nonlinear Dynamic of Atomic Force Microscope Based on Modified Couple Stress Theory [Volume 19, Issue 4, 2019, Pages 1029-1038]
Ghazanfari, M. Nonlinear Free Vibration Analysis of Composite Plate in Car Body of High Speed Trains [Volume 19, Issue 12, 2019, Pages 2955-2964]
Ghazanfari, M.H. Experimental Study of Surfapore Nanofluid Effect on Surface Free Energy of Calcite Rock [Volume 19, Issue 3, 2019, Pages 709-718]
Ghazavi, M.R. Nonlinear Size-Dependent Analysis of an Initially Curved Microbeam [Volume 19, Issue 2, 2019, Pages 247-258]
Ghezelayagh, M.H. Investigation of a new rapid opening valve with fibre optical system for a non-Diaphragm Shock Tube [Volume 19, Issue 5, 2019, Pages 1265-1274]
Ghobadian, B. Ducted wind turbine investigation in a wind tunnel [Volume 19, Issue 5, 2019, Pages 1297-1305]
Ghodusi Borujeni, F. Investigating the effect of construction defects on the Casing Collapse Strength [Volume 19, Issue 12, 2019, Pages 3031-3038]
Gholami, H. Numerical Study of Evaporation in a Vertical Porous Channel By the volume of fluid method in OpenFOAM [Volume 19, Issue 2, 2019, Pages 317-326]
Gholami, M. Theoretical and Numerical Investigation of Environmental Effects on Mechanical Behavior of Biodegradable Polymers [Volume 19, Issue 12, 2019, Pages 2837-2846]
Gholinia, M. Numerical Simulation of the Boiling Phenomenon in Improving the Cooling of a Heavy-Duty Diesel Engine with Natural Gas [Volume 19, Issue 2, 2019, Pages 363-373]
Gholipoor, A. Numerical and Experimental Investigation of Magnetic Field and Ultrasonic Vibrations Assisted EDM Process [Volume 19, Issue 1, 2019, Pages 159-169]
Ghorbani, B. Retrofit Of Steam Power Plant Using Solar Dish Collectors and Multi-Effect Desalination Cycle (Exergy and Economic Analysis) [Volume 19, Issue 12, 2019, Pages 3007-3022]
Ghorbanzadeh, S. Simultaneous Numerical Modelling of Heat Transfer and Magnetic Fields in a Vacuum Induction Furnace [Volume 19, Issue 4, 2019, Pages 959-967]
Ghoytasi, I. Thermal Effects on Free Vibration of Functionally Graded Curved Timoshenko Nanobeams Resting on WinklerâPasternak Elastic Foundation [Volume 19, Issue 12, 2019, Pages 2865-2875]
Golchin, H. Experimental Study of the Effect of Probe Calibration on the Mass Flow and Velocity Measurement of Hot Air at High-Subsonic Mach Numbers [Volume 19, Issue 7, 2019, Pages 1805-1817]
Gorji, H. Determination of Process Window of St12 Steel Sheet in Single Point Incremental Forming of a Truncated Pyramid by Experimental Method [Volume 19, Issue 10, 2019, Pages 2551-2558]
H
Habibi, M. Investigation the Effect of Loading Rates on Fracture Toughness of Loading Mode I in Glass / Epoxy Composite Laminates by Acoustic Emission [Volume 19, Issue 12, 2019, Pages 2917-2925]
Hadi, A. Design of a basic module for angular motion of spherical joints using the actuators of shape memory alloys and magnetic stabilization system [Volume 19, Issue 2, 2019, Pages 375-386]
Hadidi, A. Behaviour of Dielectric Fluid Droplet under the Influence of Uniform Magnetic Field [Volume 19, Issue 12, 2019, Pages 2847-2856]
Hadi Doolabi, M. Numerical Study of Aerodynamic Behavior of a Plunging Airfoil in Ground Effect [Volume 19, Issue 3, 2019, Pages 753-763]
Hadizadeh, A. Investigation of Mixed Convection Flow in a Lid-driven Cavity Filled with Micropolar Nanofluid [Volume 19, Issue 6, 2019, Pages 1483-1494]
Haerian Ardakani, A. Simulation of Mechanical Behavior and Construction of Regular PLA Scaffolds [Volume 19, Issue 8, 2019, Pages 1953-1958]
Haghighi Poshtiri, A. Investigation of Mixed Convection Flow in a Lid-driven Cavity Filled with Micropolar Nanofluid [Volume 19, Issue 6, 2019, Pages 1483-1494]
Haghpanahi, M. Nonlinear Viscoelastic Formulation of Spinal Ligament [Volume 19, Issue 9, 2019, Pages 2227-2234]
Hajabdollahi, H. Multi-objective Optimization of Multi-tube Heat Exchanger Network Considering the Effect of Different Nanoparticles [Volume 19, Issue 6, 2019, Pages 1507-1518]
Haji Ahmadi, S. Predicting Tearing Force for Square Cup Deep Drawing Process by Dimensionless Analysis of the Effective Geometric Parameters [Volume 19, Issue 10, 2019, Pages 2419-2430]
Hajibagheri, H.R. Experimental Relationship of Yield and Tensile Strengths with Hardness in High Strength APIX70 Steel Pipes [Volume 19, Issue 1, 2019, Pages 85-93]
Hajilary, N. Optimization of Combustion Burner at Hoffman Brick Factories [Volume 19, Issue 5, 2019, Pages 1095-1101]
Hajimohamadi, M. Determination of Stress Intensity Factor for Unequal Cracks Emanating from a Quasi-square Hole under Shear [Volume 19, Issue 1, 2019, Pages 21-28]
Hamedi, F. Simulation and Parametric Analysis of Zigzag Cooling Flow Path in a Disc-Type Transformer Winding to Investigate Parameters Affecting Cooling Conditions [Volume 19, Issue 5, 2019, Pages 1177-1186]
Hamedi, M.H. Thermodynamic, Economic and Case Study of Synthesis Gas Using the Biomass Gasification Reactor in Distributed Generation Systems [Volume 19, Issue 6, 2019, Pages 1417-1428]
Hamzeloo, S.R. Estimating the Residual Strength of Polyurethane Foam Core Sandwich Panels with Fiber Glass- Polyester Skin Using Acoustic Emission [Volume 19, Issue 3, 2019, Pages 587-596]
Hasanghasemi, M. Design and Implementation of Terminal Sliding Mode Controller for Tracking a Wheeled Mobile Robot [Volume 19, Issue 12, 2019, Pages 2887-2894]
Hasannia, A. Simultaneous Numerical Modelling of Heat Transfer and Magnetic Fields in a Vacuum Induction Furnace [Volume 19, Issue 4, 2019, Pages 959-967]
Hasanzadeh, R. A Review on Principles and Fundamentals of Fabrication of Polymeric Foams in Regards to Increasing Cell Density/ Reducing Cell Size [Volume 19, Issue 1, 2019, Pages 211-222]
Hasanzadeh, R. Optimization of solid and radiation thermal conductivity of polymeric foams using response surface method based on a novel theoretical model [Volume 19, Issue 9, 2019, Pages 2165-2173]
Hasanzadeh, R. Estimating the Thermal Conductivity of Polymeric Foams Based on a Theoretical Model Using Cell Size and Foam Density [Volume 19, Issue 9, 2019, Pages 2273-2283]
Hashemabadi, S.H. CFD Simulation of Transit-time Ultrasonic Flowmeter with PZT-5J Piezoelectric Sensor for Light, Heavy, and Medium Crude Oil [Volume 19, Issue 6, 2019, Pages 1337-1346]
Hashemi, H. Investigation of Macroscopic Fracture Surface Characteristics of API X65 Steel Using Three-point Bending Test [Volume 19, Issue 7, 2019, Pages 1591-1600]
Hashemi, R. Characterization of the Plastic and Elastic Properties of Aluminum Sheet Produced by CRB Process via DIC Method [Volume 19, Issue 2, 2019, Pages 505-513]
Hashemi, S.H. Investigation of Macroscopic Fracture Surface Characteristics of API X65 Steel Using Three-point Bending Test [Volume 19, Issue 7, 2019, Pages 1591-1600]
Hashemian, M. Dynamic Instability Analysis of Moderately Thick Rectangular Plates Influenced by an Orbiting Mass Based on the First-order Shear Deformation Theory [Volume 19, Issue 9, 2019, Pages 2203-2213]
Hashemi Mehne, S.H. Multi-Disciplinary Multi-Objective Shape Optimization of Orion Type Re-entry Capsule [Volume 19, Issue 3, 2019, Pages 665-675]
Hassani, A. Theoretical and Numerical Investigation of Environmental Effects on Mechanical Behavior of Biodegradable Polymers [Volume 19, Issue 12, 2019, Pages 2837-2846]
Hassanzadeh, H. Modeling of Laminar Fully Developed Flow in the Presence of Mass and Heat Transfer inside the Fuel Cell Channel [Volume 19, Issue 6, 2019, Pages 1363-1374]
Hassanzadeh, H. The Energy and Exergy Analysis of a Solid Oxide Fuel Cell and Gas Turbine for Desalination System [Volume 19, Issue 11, 2019, Pages 2737-2749]
Hassanzadeh, H. Air Inlet Angle Effects in Swirling Diffuser of UFAD Systems on Micron Particles Pattern Distribution [Volume 19, Issue 12, 2019, Pages 3083-3093]
Hassanzadeh, M. Computation of First and Second-Order Sensitivities for Steady State Incompressible Laminar Flow Using Extended Complex Variables Method [Volume 19, Issue 1, 2019, Pages 237-246]
Heidari, A. Experimental Relationship of Yield and Tensile Strengths with Hardness in High Strength APIX70 Steel Pipes [Volume 19, Issue 1, 2019, Pages 85-93]
Heidari, Sh. Investigating the Behavior of Aluminum 7075 under the Process of CGP as the Fin of Space Structures [Volume 19, Issue 5, 2019, Pages 1187-1197]
Heidary, M. Homogenization of Porous Shape Memory Alloys Using Monte Carlo Technique [Volume 19, Issue 8, 2019, Pages 2013-2022]
Heidary, S.H. Design New Cable System to Drive Exoskeleton Fingers for Rehabilitation [Volume 19, Issue 1, 2019, Pages 201-209]
Heidary, S.H. Pedestrian tracking by means of inertial navigation system [Volume 19, Issue 2, 2019, Pages 407-414]
Heidary, S.H. Heart Rate Measurement with Imaging Photoplethysmography Signals Using Smart Phone [Volume 19, Issue 7, 2019, Pages 1751-1757]
Heidary, S.H.R. Analytical Tow-Dimensional Modeling of Blood Flow in a Balloon with Periodic Inflation and Deflation; Application in Intra- and Extra-Aortic Cardiac Assist Devices [Volume 19, Issue 3, 2019, Pages 569-576]
Hendooie, L. 1D- 1D Modeling of High Pressure PEM Electrolyzers for Hydrogen Production [Volume 19, Issue 7, 2019, Pages 1663-1674]
Hojaji, M. Experimental Investigation of the Effect of Cylindrical Protuberance with Different Penetration the Thrust Vector a C-D Nozzle in Supersonic regime [Volume 19, Issue 5, 2019, Pages 1145-1154]
Hojaji, M. Experimental investigation of the penetration effects of opposite dual protuberances on thrust vector of a supersonic C-D nozzle [Volume 19, Issue 7, 2019, Pages 1741-1750]
Hojjat, Y. Introduction, Simulation and Experimental Investigation of a Planar Positioner Based on Permanent Magnet Linear Synchronous Motor Technology [Volume 19, Issue 11, 2019, Pages 2803-2810]
Hojjat, Yousef Effects of Dielectric Film Viscoelasticity on Dynamic Behavior of Dielectric Elastomer Minimum Energy Structure [Volume 19, Issue 11, 2019, Pages 2589-2597]
Honarpisheh, M. Experimental and Numerical Study of Severe Plastic Deformation in the Constrained Groove Pressing Process on the Pure Copper Sheets [Volume 19, Issue 2, 2019, Pages 269-280]
Honarpisheh, M. Effect of Cooling System on the Mechanical Properties and Residual Stress of Steel AISI 1045 in Quenching Heat Treatment [Volume 19, Issue 12, 2019, Pages 2979-2986]
Hoseini, S.H. Homogenization of Porous Shape Memory Alloys Using Monte Carlo Technique [Volume 19, Issue 8, 2019, Pages 2013-2022]
Hoseinzadeh, F. Parametric Study of the Effects of Ice Accretion on the Aerodynamic Performance of NACA0012 Airfoil Using FENSAP-ICE [Volume 19, Issue 9, 2019, Pages 2285-2297]
Hosseini, Seyed Mahmoud Multi-Objective Optimal Design and Natural Frequency Analysis of Shape Memory Alloy Composite Beams Using Genetic Algorithm [Volume 19, Issue 10, 2019, Pages 2499-2509]
Hosseini, S.H. An Experimental Investigation on a Modified Friction Assisted Tube Straining Method [Volume 19, Issue 9, 2019, Pages 2079-2084]
Hosseini Abadshapoori, M. Efficiency Enhancement of Solar Cells of a Sun Pointing Satellite with Design Optimization of Heat Pipes Configuration Using Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 789-800]
Hosseini Baghdad Abadi, S.M. Numerical Simulation of the Sinusoidal Wave Pulsed Film Cooling Effectiveness Due to the Changing Cooling Injection Parameters [Volume 19, Issue 1, 2019, Pages 191-200]
Hosseini Dehshiri, S.Sh. Examining the Performance of New Double L-Shaped Micromixer Type [Volume 19, Issue 4, 2019, Pages 1009-1020]
Hosseini Kordkheili, S.A. Comparison of Instantaneous Properties Extraction Methods and Execution of Optimal Empirical Mode Decomposition on Faulty Ball Bearing Experimental Data [Volume 19, Issue 7, 2019, Pages 1697-1709]
Hosseini Moghadam Omami, A. Numerical and Experimental Analysis of Hydro Screw Turbine with Variable Pitch [Volume 19, Issue 2, 2019, Pages 457-466]
Hosseini-Moradi, S.A. Experimental Study and Simulation of Semi-Constrained Groove Pressing of Interstitial Free Steel Sheet [Volume 19, Issue 11, 2019, Pages 2781-2791]
Hosseinipour, S.J. Investigating the Effect of Geometric Parameters on Forming AA6063 Cylindrical Step Tubes by Hot Metal Gas Forming Process [Volume 19, Issue 8, 2019, Pages 1865-1873]
Hosseinzadeh, M. Modeling of an Evacuated Tube Solar Cooker and Investigation of Weather Parameters Effect [Volume 19, Issue 7, 2019, Pages 1573-1584]
Hossini, Sh. Adaptive-Fuzzy Controller Design Based on the EULERINT Criterion for Satellit [Volume 19, Issue 12, 2019, Pages 2895-2905]
I
Imani, F. Experimental Identification of Mechanical and Damping Properties of a Viscoelastic Material Using the Relaxation Test [Volume 19, Issue 10, 2019, Pages 2571-2579]
Irani, S. Designing l_1 norm Based Sliding Mode Controller For Implementing in Hybrid Model of Gas Turbine [Volume 19, Issue 10, 2019, Pages 2339-2350]
Iranmanesh, M. Investigation on the Effect of Guaranteed Selling of Generated Electric Power and Other Effective Parameters on the Application of CHP System in Iranian Industries [Volume 19, Issue 5, 2019, Pages 1221-1227]
Iranmanesh, M. Effect of Forced Convection and PCM Materials on an Indirect Solar Dryer Equipped with Evacuated Heat Pipe Collector [Volume 19, Issue 11, 2019, Pages 2607-2614]
Izadi, T. Numerical Analysis of the Effect of Train Movement Inside Underground Subway Tunnels on the Air-Exchange Systems by Comparing Fan-Off and Fan-On Conditions [Volume 19, Issue 11, 2019, Pages 2679-2687]
J
Jaafarian, S.M. Effect of Gurney Flap on Airfoil Lift Coefficient by Design of Experiment (DOE) Method [Volume 19, Issue 12, 2019, Pages 2857-2863]
Jabbari, M. Electric Response of Piezoelectric Nonlinear Beam with the Harmonic Base Excitation and Change Concentrated Mass [Volume 19, Issue 2, 2019, Pages 467-474]
Jabbari, M. Effect of Dynamic Parameters and Fluid Impurities on Abrasion of Centrifugal Compressor Impeller of the Gas Transmission Center using Experimental and Analytical Methods [Volume 19, Issue 11, 2019, Pages 2645-2651]
Jafari, H. Study of Microstructure and Mechanical Properties of Dissimilar Friction Welded Martensitic Stainless Steel 410 to Austenitic Stainless Steel 304 [Volume 19, Issue 2, 2019, Pages 439-445]
Jafari, M.M. Numerical Analysis of Flow Separation Control on a BWB Drone Using a Vortex Generator [Volume 19, Issue 2, 2019, Pages 447-456]
Jafari, S. Investigating the effect of construction defects on the Casing Collapse Strength [Volume 19, Issue 12, 2019, Pages 3031-3038]
Jafari Fesharaki, J. Measurement of Acoustoelastic Constant in Iron-Base Alloy Based on Acoustoelasticity Theory for Stress Evaluation [Volume 19, Issue 10, 2019, Pages 2321-2328]
Jafarmadar, S. The thermodynamic analysis of a novel integrated transcritical CO2 with Kalina 11 cycles from Sabalan geothermal wells [Volume 19, Issue 2, 2019, Pages 335-346]
Jafarpur, Kh. Numerical Analysis of the Heat Sink Effect of Blood Vessels on Hepatic Radiofrequency and Microwave Ablation [Volume 19, Issue 7, 2019, Pages 1711-1720]
Jahanara, A.H. Investigation of Micromechanical Behavior of Ferrite and Martensite in Dual Phase Steels [Volume 19, Issue 7, 2019, Pages 1733-1740]
Jahani, K. Identification of Parameters of Spencer Model for a Double-Ended Magnetorheological Damper with Different Spherical Iron Carbonyl Powder Sizes [Volume 19, Issue 5, 2019, Pages 1307-1317]
Jahani, K. Experimental Study of the Effects of Iron Particles Size on Damping Force and Energy Dissipation of a Double-Ended Magnetorheological Damper [Volume 19, Issue 9, 2019, Pages 2129-2138]
Jahani, K. Experimental Identification of Mechanical and Damping Properties of a Viscoelastic Material Using the Relaxation Test [Volume 19, Issue 10, 2019, Pages 2571-2579]
Jalalifar, H. Investigating the effect of construction defects on the Casing Collapse Strength [Volume 19, Issue 12, 2019, Pages 3031-3038]
Jalali Vahid, D. Design, Construction and Analysis of the Gamma-Type Solar Stirling Engine by Parabolic Solar Collector [Volume 19, Issue 9, 2019, Pages 2255-2262]
Jalili, M.M. Longitudinal Free Vibrations of a Rod with Variable Cross-Section Undergoing Finite Strain [Volume 19, Issue 2, 2019, Pages 429-437]
Jamaati, J. 3D Modeling of the Effects of Arrangement and Geometry of the Rod Matrix on the Capturing of Micro-Particles in High Gradient Magnetic Filters [Volume 19, Issue 10, 2019, Pages 2471-2480]
Jamali, A. Multi-Objective Optimum Design of a Neuro-Fuzzy Network Using a Combined PSO and DE Algorithm Based on Fuzzy Logic [Volume 19, Issue 2, 2019, Pages 475-482]
Jamshid, A. Flutter Analysis of CNT-Reinforced Functionally Graded Composite Wing with Attached Mass [Volume 19, Issue 8, 2019, Pages 1855-1864]
Jamshidian, M. Three-Dimensional Finite Element Modeling of Particle Motion under the Influence of Acoustic Radiation Force in Microchannel [Volume 19, Issue 2, 2019, Pages 483-490]
Jamshidian, M. Calculating the Size-dependent Surface Energy of Metallic Spherical Nanoparticles and Nanocavities Using Molecular Dynamics [Volume 19, Issue 4, 2019, Pages 1001-1007]
Jamshidi Aval, H. Investigating the Effect of Geometric Parameters on Forming AA6063 Cylindrical Step Tubes by Hot Metal Gas Forming Process [Volume 19, Issue 8, 2019, Pages 1865-1873]
Jamshidifard, S. Experimental and Numerical Study of Effective Parameters on Helical One-channel Dust-concentrator Performance for Separation of Black Powder of Gas Pipeline [Volume 19, Issue 5, 2019, Pages 1167-1176]
Jashnani, H.R. Experimental Study on the Functionally Graded Ni-P-Al2O3 Coating Created on AA 5xxx Series for Wear Resistance Improvement by Pulse-Electrodeposition Method [Volume 19, Issue 2, 2019, Pages 293-302]
Javadi, A. Numerical Analysis of Water Injection Effect on NOx Reduction of MGT-40 Gas Turbine [Volume 19, Issue 2, 2019, Pages 397-405]
Javadi, Z. Retrofit Of Steam Power Plant Using Solar Dish Collectors and Multi-Effect Desalination Cycle (Exergy and Economic Analysis) [Volume 19, Issue 12, 2019, Pages 3007-3022]
Javanbakht, M. Investigating the Vibrational and Damping Properties of Graphite Nano - Platelet/Epoxy Composites [Volume 19, Issue 9, 2019, Pages 2263-2271]
Javanbakht, M. Finite Element Analysis of Phase Field Equations for Martensitic Phase Transformations at the Nanoscale [Volume 19, Issue 11, 2019, Pages 2771-2780]
Jhandydied, S. The Energy and Exergy Analysis of a Solid Oxide Fuel Cell and Gas Turbine for Desalination System [Volume 19, Issue 11, 2019, Pages 2737-2749]
K
Kabiri Ataabadi, A.R. Investigation of Effect of Structural Parameters on High Velocity Impact Resistance of Fiber Metal Laminates [Volume 19, Issue 6, 2019, Pages 1529-1538]
Kafaee Razavi, M. Simulation of Mechanical Behavior and Construction of Regular PLA Scaffolds [Volume 19, Issue 8, 2019, Pages 1953-1958]
Kaffash Mirzarahimi, M. Dynamic and Vibration Analysis of Composite Timoshenko Beam with Piezoelectric Layers [Volume 19, Issue 11, 2019, Pages 2689-2696]
Kakaee, A.H. Feasibility Study of Partially Stratified Charge Mixture Formation and Its Effects on CNG Direct Injection Engine [Volume 19, Issue 10, 2019, Pages 2329-2338]
Kakaei, M.M. Dynamic modeling and Designing a dynamic based control algorithm for legged quadruped robot locomotion [Volume 19, Issue 11, 2019, Pages 2635-2644]
Kalantar, V. Experimental Investigation of the Effect of Different Parameters on the Thermal Performance of the Vapor Chamber for Cooling the Electronic Board [Volume 19, Issue 10, 2019, Pages 2387-2395]
Kalhor, A. Mechanical Improvement, Simulation, and Implementation of a Visual Servoing Position Controller of a 4-DOF Delta Parallel Robot [Volume 19, Issue 1, 2019, Pages 115-123]
Kalteh, M. Study of Heat Transfer of Periodic Electroosmotic/Pressure Driven Nanofluid Flow in a Microchannel Using the Poisson-Boltzmann Method [Volume 19, Issue 3, 2019, Pages 765-776]
Kalteh, M. Simulation and Comparison of the Effect of Oxidizing Gas and Different Devolatilization Models in an Entrained-Flow Coal Gasifier [Volume 19, Issue 12, 2019, Pages 3071-3082]
Kamyab, M.H. Numerical and Experimental Study of Oblique Penetration of a Blunt Projectile into Ceramic- Aluminum Target [Volume 19, Issue 5, 2019, Pages 1253-1263]
Karafi, M.R. Effects of Dielectric Film Viscoelasticity on Dynamic Behavior of Dielectric Elastomer Minimum Energy Structure [Volume 19, Issue 11, 2019, Pages 2589-2597]
Karamad, H. Nonlinear Dynamics Control and Analysis of Atomic Force Microscope Based On Nonlocal Model [Volume 19, Issue 12, 2019, Pages 2987-2997]
Karami, F. Analytical Investigation of MHD Nanofluid Flow between Non-Parallel Stretching/Shrinking Walls with Considering Joule Heating Effect [Volume 19, Issue 3, 2019, Pages 697-708]
Karevan, M. Investigating the Vibrational and Damping Properties of Graphite Nano - Platelet/Epoxy Composites [Volume 19, Issue 9, 2019, Pages 2263-2271]
Karimi, M. Numerical and Experimental Investigation of the Effect of Droplet Collision Regime to Surface on the Performance of the Separation of Water Droplets from Air in a Zigzag Demister [Volume 19, Issue 3, 2019, Pages 549-558]
Karimian, A. Onset Yield Analysis of Rotating Variable Thickness Disk Made of Functionally Graded Materials in Engine of Aero Gas Turbine [Volume 19, Issue 9, 2019, Pages 2247-2254]
Karimpour, M. Biomechanical Analysis of Effect of Inclination Angle on Stress Distribution in the Acetabulum and Acetabularcup after Total Hip Arthroplasty [Volume 19, Issue 3, 2019, Pages 559-567]
Karimzadeh, A. Experimental Study on the Functionally Graded Ni-P-Al2O3 Coating Created on AA 5xxx Series for Wear Resistance Improvement by Pulse-Electrodeposition Method [Volume 19, Issue 2, 2019, Pages 293-302]
Karrari, M. Optimal Control Algorithm Design for the Microfluidic Channel Network Droplet Generation with Output Feedback Delay [Volume 19, Issue 7, 2019, Pages 1585-1590]
Kashani, S. Computation of First and Second-Order Sensitivities for Steady State Incompressible Laminar Flow Using Extended Complex Variables Method [Volume 19, Issue 1, 2019, Pages 237-246]
Kasiri Bidhendi, N. Experimental and Numerical Study of Effective Parameters on Helical One-channel Dust-concentrator Performance for Separation of Black Powder of Gas Pipeline [Volume 19, Issue 5, 2019, Pages 1167-1176]
Kayhani, M.H. Experimental Study and Visualization of Particle/Bubble Collision in the Presence of Fluid [Volume 19, Issue 7, 2019, Pages 1601-1611]
Kazemi, Kh. Numerical Simulation of Nanofluid Heat Transfer in a Tube Equipped with Twisted Tape Using the Eulerian-Lagrangian Two-Phase Model [Volume 19, Issue 1, 2019, Pages 53-62]
Kazemi, M. Optimization of Spring-back in Bending Process of Aluminum A1050-H14 Sheet Using Hybrid of Finite Element Method and Multi-Objective Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 919-925]
Kazemi, M. High Velocity Impact on Sandwich Panels with Graded Foam-cored and Aluminum Face-sheet: Numerical and Experimental Assessment [Volume 19, Issue 4, 2019, Pages 1039-1047]
Kazemi, M. Investigation of Aerodynamic and Heat Transfer Performance of Cylinders Using Plasma Actuators [Volume 19, Issue 9, 2019, Pages 2111-2120]
Kazemian, A.H. Effect of Gurney Flap on Airfoil Lift Coefficient by Design of Experiment (DOE) Method [Volume 19, Issue 12, 2019, Pages 2857-2863]
Kazemian, M.E. Effect of Gurney Flap on Airfoil Lift Coefficient by Design of Experiment (DOE) Method [Volume 19, Issue 12, 2019, Pages 2857-2863]
Kazemi Mazandarani, S.R. Optimization of Geometric Dimensions of Fire Tube and Heat Coil Used in City Gate Stations Heaters [Volume 19, Issue 5, 2019, Pages 1103-1114]
Kazemiyan, M. Theoretical and Numerical Investigation of Environmental Effects on Mechanical Behavior of Biodegradable Polymers [Volume 19, Issue 12, 2019, Pages 2837-2846]
Kebriaee, A. Experimental Study of Liquid Sheet Breakup in Cross Flow [Volume 19, Issue 4, 2019, Pages 845-853]
Keikhaie, N. Strengthening Defected Dam Gates under Cavitation Vibration Using CFRP [Volume 19, Issue 4, 2019, Pages 825-831]
Keramat Siavash, N. Ducted wind turbine investigation in a wind tunnel [Volume 19, Issue 5, 2019, Pages 1297-1305]
Keshavarzi, Ahmad Pareto Optimization of a Three-Dimensional Full Vehicle Suspension Model Using Multi-Objective Genetic Algorithm [Volume 19, Issue 8, 2019, Pages 1971-1978]
Keshavarzpour, H. Surface and Magnetic Field Effects Analysis on the Primary and Superharmonic Resonance Frequency Response of Single Walled CNT [Volume 19, Issue 1, 2019, Pages 1-9]
Keshaverzian, H. Effect of Dynamic Parameters and Fluid Impurities on Abrasion of Centrifugal Compressor Impeller of the Gas Transmission Center using Experimental and Analytical Methods [Volume 19, Issue 11, 2019, Pages 2645-2651]
Keshtgar, M. Aeroelastic Analysis of a Double-Sweep Wing with the Metal/Composite Sections [Volume 19, Issue 4, 2019, Pages 927-935]
Khabaz Kashani, H. Analysis of Circular Hole and Thermal Cycle Effects on the Mechanical Properties in Multi-Layer Polymer Composite Reinforced with Nanoparticles [Volume 19, Issue 1, 2019, Pages 229-236]
Khajeh Arzani, H. Investigation of Effect of Structural Parameters on High Velocity Impact Resistance of Fiber Metal Laminates [Volume 19, Issue 6, 2019, Pages 1529-1538]
Khajepour, S. Direct Steam Generation Solar Power Plant in The Two Pressures Cycle [Volume 19, Issue 1, 2019, Pages 11-19]
Khalilarya, Sh. The thermodynamic analysis of a novel integrated transcritical CO2 with Kalina 11 cycles from Sabalan geothermal wells [Volume 19, Issue 2, 2019, Pages 335-346]
Khalili, Kh. The Use of Internal Mechanical Insert to Prevent Wrinkling Defects in T-joint Hydroforming Process [Volume 19, Issue 8, 2019, Pages 1989-2000]
Khalili, P. Fuzzy Control for Drug Delivery in Cancerous Tumors Chemotherapy [Volume 19, Issue 6, 2019, Pages 1467-1473]
Khalili Sarbangholi, S. Thermo-economic Analysis of Waste Heat Recovery by the Use of Engine Exhaust Gases beside the Jacket Cooling Water of the Marine Engine [Volume 19, Issue 3, 2019, Pages 687-696]
Khalilpour Seyedi, S.A. Joint-Space Position Control of a Deployable Cable Driven Robot in Joint Space Using Force Sensors and Actuator Encoders [Volume 19, Issue 11, 2019, Pages 2615-2625]
Khalkhali, A. Effectiveness of Blade Thickness Distribution on the Turbocharger Turbine Aerostatic Performance [Volume 19, Issue 11, 2019, Pages 2667-2677]
Kharati-Koopaee, M. Investigating the Effect of Speed Variation on Performance of a Ducted Single-Stage Axial Flow Fan in the Presence of a Blade Tip-Pattern [Volume 19, Issue 1, 2019, Pages 29-41]
Kharestani, A.A. Dynamic and Vibration Analysis of Composite Timoshenko Beam with Piezoelectric Layers [Volume 19, Issue 11, 2019, Pages 2689-2696]
Khatibi, M. Numerical Study of the Thermo-physical Properties Effects of a Finned Flat-tube Heat Exchanger Body Material on the Adsorption Chiller Performance [Volume 19, Issue 3, 2019, Pages 515-526]
Khayat, M. Numerical Simulation of Droplet Falling and Positioning on Surface Using Multiphase Lattice Boltzmann Model [Volume 19, Issue 1, 2019, Pages 171-179]
Khayat, M. Experimental Study of the Effect of Hybrid Nanofluids Deposition on Microchannels with Different Sections in Pool Boiling [Volume 19, Issue 11, 2019, Pages 2653-2666]
Khazaee, I. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Kheradmand, S. Numerical Simulation of the Effect of Fuel Injection Condition on the Diesel and Gasoline Spray Characteristics in a Direct Injection Compression Ignition Engine [Volume 19, Issue 4, 2019, Pages 901-910]
Kheradmand, S. Numerical Investigation of Ambient Temperature and Actual Impactor Plates Effects on Its Efficiency [Volume 19, Issue 6, 2019, Pages 1327-1335]
Kheradmand, S. 3D Numerical Simulation of Laser Diode Heat Sink to Estimate the Effect of Geometry Variation [Volume 19, Issue 11, 2019, Pages 2793-2801]
Khoddami Maraghi, Z. Vibration Analysis of Polymer Nanocomposite-Magnetostrictive Faced Sandwich Plate Including Feedback Control System [Volume 19, Issue 11, 2019, Pages 2823-2835]
Khonsarian, R. Vision-Based Model Predictive Control of Wheeled Mobile Robot [Volume 19, Issue 7, 2019, Pages 1767-1777]
Khorrambakht, R. Joint-Space Position Control of a Deployable Cable Driven Robot in Joint Space Using Force Sensors and Actuator Encoders [Volume 19, Issue 11, 2019, Pages 2615-2625]
Khorshidi Mal Ahmadi, J. Investigating the Behavior of Aluminum 7075 under the Process of CGP as the Fin of Space Structures [Volume 19, Issue 5, 2019, Pages 1187-1197]
Khoshnood, A.M. Designing l_1 norm Based Sliding Mode Controller For Implementing in Hybrid Model of Gas Turbine [Volume 19, Issue 10, 2019, Pages 2339-2350]
Khoshrooz, P. Analytic model for investigation of effect of temperature change on residual stress and curvature of symmetric and un-symmetric composite laminates [Volume 19, Issue 9, 2019, Pages 2155-2164]
Khosravy, M. Efficiency Enhancement of Solar Cells of a Sun Pointing Satellite with Design Optimization of Heat Pipes Configuration Using Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 789-800]
Khosrowjerdi, M.J. Investigating the Effect of Different Sensors on the Observer Performance in Vehicle Suspension System Based on the Observable Degree Analysis [Volume 19, Issue 7, 2019, Pages 1675-1684]
Kianfar, K. Accessibility to the Geographic Location of Earth's Magnetic Field with Simulation & Data Collection [Volume 19, Issue 8, 2019, Pages 2031-2038]
Kianvash, A. Numerical and Experimental Investigation on Boding Strength Optimization of Glass Fibers-Reinforced Epoxy Composites on a Structural Steel Substrate [Volume 19, Issue 2, 2019, Pages 387-396]
Kohdaragh, M. Experimental Study of Damage Detection in Beam Using Dynamic Excitation System and Wavelet Packet Transform and Energy Rate Index [Volume 19, Issue 7, 2019, Pages 1655-1662]
Koohestani, S. Investigation of the Effect of Shroud on Natural Frequencies of a Rotating Multi Blade System [Volume 19, Issue 8, 2019, Pages 1889-1896]
Kouhikamali, R. Numerical Study of Evaporation in a Vertical Porous Channel By the volume of fluid method in OpenFOAM [Volume 19, Issue 2, 2019, Pages 317-326]
Kouhikamali, R. Numerical and Experimental Investigation of the Effect of Droplet Collision Regime to Surface on the Performance of the Separation of Water Droplets from Air in a Zigzag Demister [Volume 19, Issue 3, 2019, Pages 549-558]
L
Lezgy-Nazargah, M. Free Vibration Analysis of Functionally Graded Magneto-electro-elastic Plates Resting on Elastic Foundations with Considering Interfacial Imperfections [Volume 19, Issue 3, 2019, Pages 655-663]
Lotfollahi Yaghin, M.A. Experimental Study of Damage Detection in Beam Using Dynamic Excitation System and Wavelet Packet Transform and Energy Rate Index [Volume 19, Issue 7, 2019, Pages 1655-1662]
M
Maani, E. Effect of Fluid and Size on the Nonlinear Dynamic of Atomic Force Microscope Based on Modified Couple Stress Theory [Volume 19, Issue 4, 2019, Pages 1029-1038]
Maaref, Y. Numerical Analysis of the Heat Sink Effect of Blood Vessels on Hepatic Radiofrequency and Microwave Ablation [Volume 19, Issue 7, 2019, Pages 1711-1720]
Maddahian, R. Numerical Simulation of Nanofluid Heat Transfer in a Tube Equipped with Twisted Tape Using the Eulerian-Lagrangian Two-Phase Model [Volume 19, Issue 1, 2019, Pages 53-62]
Madoliat, R. Postbuckling Analysis of Laminated Composites with Cutout Using Experimental, Numerical, and Finite Strip Methods [Volume 19, Issue 8, 2019, Pages 2067-2077]
Maerefat, M. Optimum Insulation Thickness Based on Energy Carriers Different Tariffs in Climatic Condition of Tehran [Volume 19, Issue 6, 2019, Pages 1447-1456]
Maghsudi, P. Modeling of Laminar Fully Developed Flow in the Presence of Mass and Heat Transfer inside the Fuel Cell Channel [Volume 19, Issue 6, 2019, Pages 1363-1374]
Mahbod, M. Mechanical Properties of Functionally Graded Porous Biomaterials for Application in Prosthesis Replacement Using Analytical and Numerical Solution [Volume 19, Issue 11, 2019, Pages 2717-2727]
Mahdavi, A.M. Evaluation of Rarefied Shear Flow in Micro/Nano Geometries Using Fokker-Planck Technique [Volume 19, Issue 7, 2019, Pages 1721-1732]
Mahdavi, E. Evaluation of the Heat Transfer Coefficient of Multi-walled Boron Nitride Nanotubes [Volume 19, Issue 9, 2019, Pages 2105-2110]
Mahdian, Asghar Pareto Optimization of a Three-Dimensional Full Vehicle Suspension Model Using Multi-Objective Genetic Algorithm [Volume 19, Issue 8, 2019, Pages 1971-1978]
Mahjoub Moghadas, S. Dynamic and Vibration Analysis of Composite Timoshenko Beam with Piezoelectric Layers [Volume 19, Issue 11, 2019, Pages 2689-2696]
Mahmoodi, E. Ducted wind turbine investigation in a wind tunnel [Volume 19, Issue 5, 2019, Pages 1297-1305]
Mahmoodi, M. New Strategy to Simultaneous Increase in Strength and Electrical Conductivity of UFG Copper Strip Fabricated via Accumulative Roll Bonding- Cold Roll Bonding [Volume 19, Issue 9, 2019, Pages 2085-2092]
Mahmoudimehr, J. A Parametric Study on Optical Performance of a Multi-Tubular Solar Reactor by Monte-Carlo ray Tracing Method [Volume 19, Issue 3, 2019, Pages 643-653]
Mahmoudkhani, S. Effects of the Disk Flexibility on the Flutter and Aeroelastic Response of Mistuned Bladed Disks [Volume 19, Issue 8, 2019, Pages 1907-1916]
Malek Ghaini, F. Numerical and experimental investigation of current and electrode force effects on expulsion in resistance spot welding of galvanized and non-galvanized steel sheets [Volume 19, Issue 7, 2019, Pages 1797-1804]
Maleki, S. Investigating the Crack Propagation at the Surface of the Composite Patch Bonding to the Steel Substrate [Volume 19, Issue 8, 2019, Pages 1897-1906]
Maleki, S. Nonlinear Dynamics Control and Analysis of Atomic Force Microscope Based On Nonlocal Model [Volume 19, Issue 12, 2019, Pages 2987-2997]
Maleki Bagherabadi, K. Numerical Analysis of Some Active and Passive Electro-Kinetic Micro-Mixers by Applying Poisson-Nernst-Planck and NavierâStokes (PNP-NSE) Equations [Volume 19, Issue 8, 2019, Pages 2057-2066]
Maleki Varnoosfaderani, M. Analysis of Static Performance of Noncircular Lobed Journal Bearings with Lubricants Containing TiO2 Nanoparticles Using Couple Stress Fluid Model [Volume 19, Issue 1, 2019, Pages 151-157]
MalekzadehFard, K. Experimental Measurement of Parameters for High Velocity Impact Simulation on Composite Plate Based On PDM and CZM [Volume 19, Issue 9, 2019, Pages 2215-2226]
Manafi Farid, H. Matrix Reinforcement Coefficients Models for Fracture Investigation of Orthotropic Materials [Volume 19, Issue 11, 2019, Pages 2811-2822]
Mansouri, M. Aeroelastic Analysis of a Double-Sweep Wing with the Metal/Composite Sections [Volume 19, Issue 4, 2019, Pages 927-935]
Manzoori, A. Study of the stability of atherosclerotic arteries using fluid-structure interaction [Volume 19, Issue 3, 2019, Pages 677-686]
Masoumpour, B. Multi-objective Optimization of Multi-tube Heat Exchanger Network Considering the Effect of Different Nanoparticles [Volume 19, Issue 6, 2019, Pages 1507-1518]
Matini, M.R. Comparative Comparison of Temperature Reduction Solutions in Homeostatic Façade [Volume 19, Issue 8, 2019, Pages 2023-2029]
Mazaheri, Y. Investigation of Micromechanical Behavior of Ferrite and Martensite in Dual Phase Steels [Volume 19, Issue 7, 2019, Pages 1733-1740]
Mazaheri, Y. Effect of ND: YAG Pulsed Laser Welding Parameters on Microstructural Evolutions and Mechanical Properties of 2205 Duplex Stainless Steel [Volume 19, Issue 10, 2019, Pages 2535-2541]
Mazaheri, Y. Numerical and Experimental Investigations of Mechanical Behavior of Hard TiAlN Nanostructured Coatings Applied by PVD on HSS Substrate [Volume 19, Issue 12, 2019, Pages 3063-3069]
Mazaheri, Yousef Numerical and experimental investigation of current and electrode force effects on expulsion in resistance spot welding of galvanized and non-galvanized steel sheets [Volume 19, Issue 7, 2019, Pages 1797-1804]
Mazare, M. Optimal Adaptive High-Order Super Twisting Sliding Mode Control of a Lower Limb Exoskeleton Robot [Volume 19, Issue 3, 2019, Pages 777-787]
Mazare, M. Individual Pitch Angle Robust Control of a Variable Speed Wind Turbine to Mitigate Mechanical Loads [Volume 19, Issue 4, 2019, Pages 937-945]
Mazare, M. Hybrid Active Force Control of Super-Twisting PID Sliding Mode Technique of a Lower Limb Exoskeleton [Volume 19, Issue 12, 2019, Pages 2935-2944]
Mazidi Sharafabadi, V. Investigating the Effect of Surface Roughness on Efficiency of Large Wind Farms by Large Eddy Simulation [Volume 19, Issue 10, 2019, Pages 2367-2374]
Mehrabian, M.A. Numerical Analysis of the Effect of Train Movement Inside Underground Subway Tunnels on the Air-Exchange Systems by Comparing Fan-Off and Fan-On Conditions [Volume 19, Issue 11, 2019, Pages 2679-2687]
Mehrabi Gohari, E. Thermal Analysis of Laser Welding in Joint of Stainless Steel to Low Carbon Steel Using Finite Element Method (FEM) [Volume 19, Issue 6, 2019, Pages 1475-1482]
Mehramiz, A. Analysis of Instability on the Boundary of the Inhomogeneous Fluids with Varying Densities in the Presence of Incident Shock [Volume 19, Issue 3, 2019, Pages 577-585]
Menhaj, M.B. Optimal Control Algorithm Design for the Microfluidic Channel Network Droplet Generation with Output Feedback Delay [Volume 19, Issue 7, 2019, Pages 1585-1590]
Miansari, M. Retrofit Of Steam Power Plant Using Solar Dish Collectors and Multi-Effect Desalination Cycle (Exergy and Economic Analysis) [Volume 19, Issue 12, 2019, Pages 3007-3022]
Mir, A. Study of Damage Propagation and Life Assessment in High Temperature Cyclic Loading [Volume 19, Issue 3, 2019, Pages 731-742]
Mirabdolahi, M. Optimization and Modeling of Plasma Cutting of AISI 309 Stainless Steel by Using Neural Network-Genetic Algorithm Hybrid Model [Volume 19, Issue 10, 2019, Pages 2455-2462]
Mirahmadi, J. An Experimental Investigation on a Modified Friction Assisted Tube Straining Method [Volume 19, Issue 9, 2019, Pages 2079-2084]
Mirbozorgi, S.A. Modeling of Laminar Fully Developed Flow in the Presence of Mass and Heat Transfer inside the Fuel Cell Channel [Volume 19, Issue 6, 2019, Pages 1363-1374]
Mirnia, Mohammad Javad Determination of Process Window of St12 Steel Sheet in Single Point Incremental Forming of a Truncated Pyramid by Experimental Method [Volume 19, Issue 10, 2019, Pages 2551-2558]
Mirzababaee, S.M. Modeling of an Evacuated Tube Solar Cooker and Investigation of Weather Parameters Effect [Volume 19, Issue 7, 2019, Pages 1573-1584]
Mirzaei, M. Effect of Dynamic Stability Derivatives Coefficients on the Design of Operational Parameters of the Actuator in an Underwater Robot [Volume 19, Issue 7, 2019, Pages 1623-1632]
Mirzaei, M. Investigating the Effect of Different Sensors on the Observer Performance in Vehicle Suspension System Based on the Observable Degree Analysis [Volume 19, Issue 7, 2019, Pages 1675-1684]
Mirzakhani, S. Finite Element Analysis of Phase Field Equations for Martensitic Phase Transformations at the Nanoscale [Volume 19, Issue 11, 2019, Pages 2771-2780]
Mirzaparikhany, S. A Theoretical Model for Evaporation of Leidenfrost Drop for Prediction of Vapor Layer Thickness under the Drop [Volume 19, Issue 4, 2019, Pages 969-979]
Moallemi, H. Investigating the Effect of Speed Variation on Performance of a Ducted Single-Stage Axial Flow Fan in the Presence of a Blade Tip-Pattern [Volume 19, Issue 1, 2019, Pages 29-41]
Moeinian, M. Development of a Novel Sizing Software for Plug-In Hybrid Electric Vehicles [Volume 19, Issue 12, 2019, Pages 3051-3062]
Moetakef Imani, B. Improving Active Vibration Control Performance in Machining Using Nonlinear Fractional PID Controller [Volume 19, Issue 2, 2019, Pages 281-291]
Moetakef-Imani, B. Identification of Dynamic Model for an Active Boring Bar [Volume 19, Issue 8, 2019, Pages 1917-1928]
Moghadasian, M. Optimal Landing of Unmanned Aerial Vehicle Using Vectorised High Order Expansions Method [Volume 19, Issue 11, 2019, Pages 2761-2769]
Moghiman, M. Numerical Simulation of Co-Firing of Biomass-Sulfide Concentrate and Pollutants Formation in the Flash Furnace Copper Smelting [Volume 19, Issue 12, 2019, Pages 2927-2934]
Mohajeri, S.H. Effect of Side Looking Acoustic Doppler Velocimeter (ADV) Presence on Turbulent Flow Field in Compound Channel [Volume 19, Issue 12, 2019, Pages 2945-2953]
Mohammadi, A. Formation Control and Path Tracking for a Group of Quadrotors to Carry Out a Suspended Load [Volume 19, Issue 4, 2019, Pages 887-899]
Mohammadi, A. Interfacial Tension Measurement Using Microfluidics [Volume 19, Issue 4, 2019, Pages 911-918]
Mohammadi, B. Postbuckling Analysis of Laminated Composites with Cutout Using Experimental, Numerical, and Finite Strip Methods [Volume 19, Issue 8, 2019, Pages 2067-2077]
Mohammadi, M. Thermal Analysis of Laser Welding in Joint of Stainless Steel to Low Carbon Steel Using Finite Element Method (FEM) [Volume 19, Issue 6, 2019, Pages 1475-1482]
Mohammadi, M. Experimental Study and Visualization of Particle/Bubble Collision in the Presence of Fluid [Volume 19, Issue 7, 2019, Pages 1601-1611]
Mohammadi, M. Measurement of Acoustoelastic Constant in Iron-Base Alloy Based on Acoustoelasticity Theory for Stress Evaluation [Volume 19, Issue 10, 2019, Pages 2321-2328]
Mohammadi, M. Modeling of Drug Delivery to Solid Tumor with a Remodeled Dynamic Capillary Network Induced by Two Parent Vessels [Volume 19, Issue 12, 2019, Pages 2877-2886]
Mohammadi, M.H. Design and Analysis of Axisymmetric Supersonic Inlet at Mach 3 [Volume 19, Issue 10, 2019, Pages 2543-2550]
Mohammadi Asl, H. Study of Ratcheting Behavior of 304L Stainless Steel Branch Pipes by Using Chaboche and Combined Hardening Models [Volume 19, Issue 9, 2019, Pages 2193-2201]
Mohammadipour, O.R. Numerical Investigation of Convection around Heated Circular Cylinder Wrapped with Bi-Disperse Porous Medium in Channel [Volume 19, Issue 3, 2019, Pages 539-548]
Mohammad Kari, B. Optimum Insulation Thickness Based on Energy Carriers Different Tariffs in Climatic Condition of Tehran [Volume 19, Issue 6, 2019, Pages 1447-1456]
Mohammad Nouri, M. Slip Length of the Nanocomposite Coating in Laminar Flow [Volume 19, Issue 10, 2019, Pages 2463-2469]
Mohammadpour, O. Discrete Adaptive Sliding Mode Control of an Omnidirectional Mobile Robot Using Time Delay Control Method [Volume 19, Issue 2, 2019, Pages 491-504]
Mohammadpourfard, M. Numerical and Experimental Investigation of Magnetic Field and Ultrasonic Vibrations Assisted EDM Process [Volume 19, Issue 1, 2019, Pages 159-169]
Mohammadpour Fattahi, A. Experimental Study of the Water Absorption and Fatigue Life of PMMA/MWCNTs Nanocomposites [Volume 19, Issue 7, 2019, Pages 1819-1825]
Mohammad-Zadeh Eivaghi, V. Sensitivity Analysis and Design of Univariate Alarm System Based on Delay Timer Considering Measurement Errors [Volume 19, Issue 5, 2019, Pages 1155-1165]
Mohammadzadeh Kowsari, M. Numerical Study of the Thermo-physical Properties Effects of a Finned Flat-tube Heat Exchanger Body Material on the Adsorption Chiller Performance [Volume 19, Issue 3, 2019, Pages 515-526]
Moharreri, M.R. Numerical Study of Effects of Simultaneous Changes of Geometric Parameters on the Performance of Touss Power Plant Ejector and Selecting Optimal Conditions Using Taguchi Method [Volume 19, Issue 3, 2019, Pages 621-629]
Mohebie, M. Experimental Study of the Effect of Hybrid Nanofluids Deposition on Microchannels with Different Sections in Pool Boiling [Volume 19, Issue 11, 2019, Pages 2653-2666]
Mohseni, Arman Investigating the Separation Bubble Behavior on the Suction Side of a High-Lift Low-Pressure Turbine Blade Using Proper Orthogonal Decomposition [Volume 19, Issue 10, 2019, Pages 2431-2441]
Moini, A. A Model to Determining the State of Degradation and Remaining Useful Life of Rotating Equipment, With a New Approach to Combination and Predicting Health Index [Volume 19, Issue 10, 2019, Pages 2351-2365]
Mojaddam, Mohammad Investigating the Separation Bubble Behavior on the Suction Side of a High-Lift Low-Pressure Turbine Blade Using Proper Orthogonal Decomposition [Volume 19, Issue 10, 2019, Pages 2431-2441]
Mojtahedi, A.R. Experimental Study of Damage Detection in Beam Using Dynamic Excitation System and Wavelet Packet Transform and Energy Rate Index [Volume 19, Issue 7, 2019, Pages 1655-1662]
Mokhtari, A. Design and Analysis of a Flexural Hinges Mechanism for Force and Moment Precision Measurement in Wind Tunnel Balance [Volume 19, Issue 9, 2019, Pages 2309-2320]
Mokhtari, D. Experimental Investigation of the Effect of Cylindrical Protuberance with Different Penetration the Thrust Vector a C-D Nozzle in Supersonic regime [Volume 19, Issue 5, 2019, Pages 1145-1154]
Mokhtari, M. Optimal Adaptive High-Order Super Twisting Sliding Mode Control of a Lower Limb Exoskeleton Robot [Volume 19, Issue 3, 2019, Pages 777-787]
Mokhtari, M. Hybrid Active Force Control of Super-Twisting PID Sliding Mode Technique of a Lower Limb Exoskeleton [Volume 19, Issue 12, 2019, Pages 2935-2944]
Molavian Jazi, M. Effect of Fluid and Size on the Nonlinear Dynamic of Atomic Force Microscope Based on Modified Couple Stress Theory [Volume 19, Issue 4, 2019, Pages 1029-1038]
Mollaei, F. Vancomycin Adsorption on Microcantilever Based on Molecular Dynamics Simulation [Volume 19, Issue 10, 2019, Pages 2481-2489]
Moloodi, A. Simulation of Mechanical Behavior and Construction of Regular PLA Scaffolds [Volume 19, Issue 8, 2019, Pages 1953-1958]
Momeni, A. Investigation and Modelling the Flow Behavior of Fe-17Cr-7Ni Semi-Austenitic Precipitation Hardening Stainless Steel Using the Hyperbolic Sine Constitutive Equation [Volume 19, Issue 6, 2019, Pages 1439-1445]
Momeni, M. Second Phase of Nanomanipulation of Particles by Atomic Force Microscopy Using Coulomb, HK, and LuGre Friction Models [Volume 19, Issue 1, 2019, Pages 181-190]
Momeni, V. Optimization of Injection Parameters in Metal Injection Molding of 4605 Low Alloy Steel [Volume 19, Issue 5, 2019, Pages 1199-1208]
Momeni Massouleh, S.H. Comparison of Instantaneous Properties Extraction Methods and Execution of Optimal Empirical Mode Decomposition on Faulty Ball Bearing Experimental Data [Volume 19, Issue 7, 2019, Pages 1697-1709]
Montazeri, M.J. Numerical Investigation of the Effects of Minor Geometric Changes of the Stator Blade Profiles on the Steady Performance of a High-pressure Gas-turbine [Volume 19, Issue 5, 2019, Pages 1209-1220]
Montazerin, N. Inference System Based on Fuzzy Clustering to Display the Flow Field Changes in the Rotor Outlet of Centrifugal Turbomachinery [Volume 19, Issue 6, 2019, Pages 1495-1505]
Moqtaderi, H. Simulation and Parametric Analysis of Zigzag Cooling Flow Path in a Disc-Type Transformer Winding to Investigate Parameters Affecting Cooling Conditions [Volume 19, Issue 5, 2019, Pages 1177-1186]
Mortezaei, S. Investigation and Modelling the Flow Behavior of Fe-17Cr-7Ni Semi-Austenitic Precipitation Hardening Stainless Steel Using the Hyperbolic Sine Constitutive Equation [Volume 19, Issue 6, 2019, Pages 1439-1445]
Mosayebi, M. Design and Analysis of a Flexural Hinges Mechanism for Force and Moment Precision Measurement in Wind Tunnel Balance [Volume 19, Issue 9, 2019, Pages 2309-2320]
Mosayebi, Masoud Pareto Optimization of a Three-Dimensional Full Vehicle Suspension Model Using Multi-Objective Genetic Algorithm [Volume 19, Issue 8, 2019, Pages 1971-1978]
Moslemi Petrudi, A. Numerical and Experimental Study of Oblique Penetration of a Blunt Projectile into Ceramic- Aluminum Target [Volume 19, Issue 5, 2019, Pages 1253-1263]
Moslemi Petrudi, M.A. Numerical and Experimental Study of Oblique Penetration of a Blunt Projectile into Ceramic- Aluminum Target [Volume 19, Issue 5, 2019, Pages 1253-1263]
Mossaiby, F. Simulation of Sloshing in Rectangular Tanks under Harmonic Excitation by the Generalized Exponential Basis Functions Meshless Method [Volume 19, Issue 6, 2019, Pages 1397-1408]
Mostafavi, S.A. Experimental Investigation of Air Pollution in Saveh City and Presenting the Related Solutions to Reduce It [Volume 19, Issue 12, 2019, Pages 2999-3005]
Mousavi, S.A. Dynamic and Vibration Analysis of Composite Timoshenko Beam with Piezoelectric Layers [Volume 19, Issue 11, 2019, Pages 2689-2696]
Mousazadeh, M. Identification of Parameters of Spencer Model for a Double-Ended Magnetorheological Damper with Different Spherical Iron Carbonyl Powder Sizes [Volume 19, Issue 5, 2019, Pages 1307-1317]
Mousazadeh, M. Experimental Study of the Effects of Iron Particles Size on Damping Force and Energy Dissipation of a Double-Ended Magnetorheological Damper [Volume 19, Issue 9, 2019, Pages 2129-2138]
Movahedirad, S. Experimental and Numerical Study of Effective Parameters on Helical One-channel Dust-concentrator Performance for Separation of Black Powder of Gas Pipeline [Volume 19, Issue 5, 2019, Pages 1167-1176]
Mozafari, Ali Experimental and Numerical Investigating of Failure Factors in One-Way Ring Valves in Reciprocating Compressors [Volume 19, Issue 9, 2019, Pages 2299-2308]
Mozafary, H. Effect of Multidirectional Forging on Microstructures and Mechanical Properties of Nano-SiC Reinforced AZ31 Nanocomposites [Volume 19, Issue 4, 2019, Pages 981-989]
Mozaffari, H. Modeling of Driver Behavior in Complicated Traffic Conditions by Combining Psychological Theories and Automotive Control Techniques [Volume 19, Issue 1, 2019, Pages 63-74]
Musavi, A. An Experimental Investigation on Acoustical Insulation Characteristics of the Natural Rubber Reinforced by Polyester Fibers [Volume 19, Issue 1, 2019, Pages 137-141]
N
Nabaei, M. Numerical Evaluation of the Effect of Percentage and Location of Stenosis on the Hemodynamic Bifurcation of the Left Coronary Artery [Volume 19, Issue 3, 2019, Pages 743-752]
Nabavi, M.M. 3D Numerical Simulation of Laser Diode Heat Sink to Estimate the Effect of Geometry Variation [Volume 19, Issue 11, 2019, Pages 2793-2801]
Nabipoor, M. Effect of Side Looking Acoustic Doppler Velocimeter (ADV) Presence on Turbulent Flow Field in Compound Channel [Volume 19, Issue 12, 2019, Pages 2945-2953]
Naddaf Oskouei, Alireza Experimental and Numerical Investigating of Failure Factors in One-Way Ring Valves in Reciprocating Compressors [Volume 19, Issue 9, 2019, Pages 2299-2308]
Naderi, H. Numerical and Experimental Investigations of Mechanical Behavior of Hard TiAlN Nanostructured Coatings Applied by PVD on HSS Substrate [Volume 19, Issue 12, 2019, Pages 3063-3069]
Naeemi Amini, P. Improving Active Vibration Control Performance in Machining Using Nonlinear Fractional PID Controller [Volume 19, Issue 2, 2019, Pages 281-291]
Naffakh-Moosavy, H. Effect of pre-cold treatment on weldability of Inconel 718 superalloy using Nd:YAG pulsed laser [Volume 19, Issue 2, 2019, Pages 327-334]
Naghash, A. Controller Design for a Ducted Fan MAV Using Dynamic Inversion Method in Lateral Motion [Volume 19, Issue 6, 2019, Pages 1559-1571]
Naghash, A. Vancomycin Adsorption on Microcantilever Based on Molecular Dynamics Simulation [Volume 19, Issue 10, 2019, Pages 2481-2489]
Nahvi, A. Modeling of Driver Behavior in Complicated Traffic Conditions by Combining Psychological Theories and Automotive Control Techniques [Volume 19, Issue 1, 2019, Pages 63-74]
Najafi, A.F. Numerical and Experimental Analysis of Hydro Screw Turbine with Variable Pitch [Volume 19, Issue 2, 2019, Pages 457-466]
Najafi, F. A New Hybrid Intelligent Technique Based on Improving the Compensation Distance Evaluation Technique and Support Vector Machine for Bearing Fault Diagnosis [Volume 19, Issue 4, 2019, Pages 865-875]
Najafi, Gh.H. Ducted wind turbine investigation in a wind tunnel [Volume 19, Issue 5, 2019, Pages 1297-1305]
Narimanzade, N. Multi-Objective Optimum Design of a Neuro-Fuzzy Network Using a Combined PSO and DE Algorithm Based on Fuzzy Logic [Volume 19, Issue 2, 2019, Pages 475-482]
Naseh, H. Modeling and Simulation of Fuel Sloshing in Tank by Pendulum Model [Volume 19, Issue 8, 2019, Pages 2001-2011]
Naseriasl, Z. Control Analysis of an Auxiliary Mechanism for Trajectory Tracking of Planar Seams in Robotic Welding [Volume 19, Issue 4, 2019, Pages 1021-1028]
Nasri, M. Experimental Investigation of Machining Parameters of Near Dry Electrical Discharge Machining (EDM) of Mo40 Steel Using Vegetable Oil [Volume 19, Issue 6, 2019, Pages 1539-1549]
Navabi, M. Modeling of Fuel Sloshing in a Spacecraft and Control it by Active Control Method Using Nonlinear Control [Volume 19, Issue 9, 2019, Pages 2121-2128]
Navabi, M. Modeling and Simulation of Nonlinear Dynamics of Helicopter Rotor Flapping Considering Offset, Blade Weight Moment and Frequency of Flapping [Volume 19, Issue 10, 2019, Pages 2523-2534]
Navabi, M. Adaptive-Fuzzy Controller Design Based on the EULERINT Criterion for Satellit [Volume 19, Issue 12, 2019, Pages 2895-2905]
Navidbakhsh, M. Analytical Tow-Dimensional Modeling of Blood Flow in a Balloon with Periodic Inflation and Deflation; Application in Intra- and Extra-Aortic Cardiac Assist Devices [Volume 19, Issue 3, 2019, Pages 569-576]
Nazari, F. Experimental and Numerical Study of Severe Plastic Deformation in the Constrained Groove Pressing Process on the Pure Copper Sheets [Volume 19, Issue 2, 2019, Pages 269-280]
Nazari, F. Multi-Objective Optimal Design and Natural Frequency Analysis of Shape Memory Alloy Composite Beams Using Genetic Algorithm [Volume 19, Issue 10, 2019, Pages 2499-2509]
Nazari, F. Effect of Cooling System on the Mechanical Properties and Residual Stress of Steel AISI 1045 in Quenching Heat Treatment [Volume 19, Issue 12, 2019, Pages 2979-2986]
Nazari, M. Simultaneous Numerical Modelling of Heat Transfer and Magnetic Fields in a Vacuum Induction Furnace [Volume 19, Issue 4, 2019, Pages 959-967]
Nazari, M. Simultaneous Numerical Modelling of Heat Transfer and Magnetic Fields in a Vacuum Induction Furnace [Volume 19, Issue 4, 2019, Pages 959-967]
Nazari, M. Experimental Study and Visualization of Particle/Bubble Collision in the Presence of Fluid [Volume 19, Issue 7, 2019, Pages 1601-1611]
Nazari, M.R. Onset Yield Analysis of Rotating Variable Thickness Disk Made of Functionally Graded Materials in Engine of Aero Gas Turbine [Volume 19, Issue 9, 2019, Pages 2247-2254]
Nazemi Babadi, M. Numerical Simulation of the Effect of Fuel Injection Condition on the Diesel and Gasoline Spray Characteristics in a Direct Injection Compression Ignition Engine [Volume 19, Issue 4, 2019, Pages 901-910]
Nazififard, M. Numerical Simulation of Nanofluid Heat Transfer in a Tube Equipped with Twisted Tape Using the Eulerian-Lagrangian Two-Phase Model [Volume 19, Issue 1, 2019, Pages 53-62]
Nemati Asl, Y. Study of the Strain - Stress Effect on Ferroelectric Behaviors of PbTiO3 [Volume 19, Issue 9, 2019, Pages 2149-2154]
Nematollahi, E. Numerical Study of Mixing Two-Components Non-Newtonian Fluids in Double T-Shaped Micromixers and Multiple T-Shaped with Aligned and Non-Aligned Inputs [Volume 19, Issue 4, 2019, Pages 833-844]
Nezami, R. Nonlinear Free Vibration Analysis of Composite Plate in Car Body of High Speed Trains [Volume 19, Issue 12, 2019, Pages 2955-2964]
Nezamivand Chegini, S. A New Hybrid Intelligent Technique Based on Improving the Compensation Distance Evaluation Technique and Support Vector Machine for Bearing Fault Diagnosis [Volume 19, Issue 4, 2019, Pages 865-875]
Niazmand, H Numerical Study of the Thermo-physical Properties Effects of a Finned Flat-tube Heat Exchanger Body Material on the Adsorption Chiller Performance [Volume 19, Issue 3, 2019, Pages 515-526]
Niazmand, H. Experimental Analysis of Micro- Nano Bubble Formation inside Venturi Tube with High Speed Photography and Image Processing [Volume 19, Issue 12, 2019, Pages 3039-3049]
Nikmehr, M. Experimental Investigation of the Effect of Different Parameters on the Thermal Performance of the Vapor Chamber for Cooling the Electronic Board [Volume 19, Issue 10, 2019, Pages 2387-2395]
Niknejad, F. Numerical Evaluation of the Effect of Percentage and Location of Stenosis on the Hemodynamic Bifurcation of the Left Coronary Artery [Volume 19, Issue 3, 2019, Pages 743-752]
Nikpourian, A. Nonlinear Size-Dependent Analysis of an Initially Curved Microbeam [Volume 19, Issue 2, 2019, Pages 247-258]
Nobakhti, M.H. Numerical Simulation of Droplet Falling and Positioning on Surface Using Multiphase Lattice Boltzmann Model [Volume 19, Issue 1, 2019, Pages 171-179]
Nobakhti, M.H. Numerical Investigation of the Effects of Minor Geometric Changes of the Stator Blade Profiles on the Steady Performance of a High-pressure Gas-turbine [Volume 19, Issue 5, 2019, Pages 1209-1220]
Norouzi, M. Investigation of Magneto-Rheological Fluid Properties inside MR Damper by Use of Dissipative Particle Dynamics Method [Volume 19, Issue 4, 2019, Pages 991-1000]
Nosratollahi, M. Decision-Making System Design for Satellite Temperature Management in the Presence of Fluid Momentum Controller Actuators Fault [Volume 19, Issue 4, 2019, Pages 947-957]
Nourazar, S. Experimental, Numerical, and Analytical Study of a Droplet Impact on Parallel Fibers [Volume 19, Issue 7, 2019, Pages 1645-1653]
Nourbakhsh, A. Numerical and Experimental Analysis of Hydro Screw Turbine with Variable Pitch [Volume 19, Issue 2, 2019, Pages 457-466]
Nourbakhsh, S.H. Effect of Multidirectional Forging on Microstructures and Mechanical Properties of Nano-SiC Reinforced AZ31 Nanocomposites [Volume 19, Issue 4, 2019, Pages 981-989]
Nouri Khajavi, M. Comparison of Li-Ion Battery State of Charge Prediction by Artificial Neural Network and Adaptive Neuro Fuzzy Inference System [Volume 19, Issue 1, 2019, Pages 43-52]
Nozari, M. Thermal Analysis of Laser Welding in Joint of Stainless Steel to Low Carbon Steel Using Finite Element Method (FEM) [Volume 19, Issue 6, 2019, Pages 1475-1482]
O
Olyaei, Gh. Experimental Study of Liquid Sheet Breakup in Cross Flow [Volume 19, Issue 4, 2019, Pages 845-853]
Omiddezyani, S. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Ommi, F. Numerical Study of Step Geometry Effects on Gaseous Sonic Transverse Injection in Supersonic Crossflow [Volume 19, Issue 5, 2019, Pages 1075-1084]
Ommi, F. Experimental Study of the Effect of Probe Calibration on the Mass Flow and Velocity Measurement of Hot Air at High-Subsonic Mach Numbers [Volume 19, Issue 7, 2019, Pages 1805-1817]
Osouli-Bostanabad, K. Numerical and Experimental Investigation on Boding Strength Optimization of Glass Fibers-Reinforced Epoxy Composites on a Structural Steel Substrate [Volume 19, Issue 2, 2019, Pages 387-396]
Ovesy, H.R. Flutter of a Circular Cylindrical Shell Subjected to Supersonic External Flow by Considering Internal Fluid Effects through a Novel Formulation [Volume 19, Issue 6, 2019, Pages 1355-1362]
P
Pakravan, H.A. Numerical Analysis of the Heat Sink Effect of Blood Vessels on Hepatic Radiofrequency and Microwave Ablation [Volume 19, Issue 7, 2019, Pages 1711-1720]
Panahi liavoli, R. Determination of Process Window of St12 Steel Sheet in Single Point Incremental Forming of a Truncated Pyramid by Experimental Method [Volume 19, Issue 10, 2019, Pages 2551-2558]
Parhizkar, H. Numerical Analysis of Flow Separation Control on a BWB Drone Using a Vortex Generator [Volume 19, Issue 2, 2019, Pages 447-456]
Parhizkar, H. Numerical Study of the Effect of Flow Suction on the Reduction of Acoustic Noise Due to the Flow on a Three-Dimensional Cylinder [Volume 19, Issue 5, 2019, Pages 1049-1059]
Parsa Mofrad, N. Numerical Simulation of Particle Dispersion around Respiratory System of a Standing and Sleeping Mannequin inside a Room [Volume 19, Issue 4, 2019, Pages 877-885]
Parvizi, A. Experimental Study of Weld Line Displacement and Drawing Depth in TWBs Steel Sheets Manufactured by Laser and Friction Stir Welding [Volume 19, Issue 9, 2019, Pages 2183-2192]
Pashmforoush, F. Optimization of Spring-back in Bending Process of Aluminum A1050-H14 Sheet Using Hybrid of Finite Element Method and Multi-Objective Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 919-925]
Pesteei, S.M. Exergoeconomic Analysis of a Heating and Power Generation Solar System for Using at the Engineering Faculty of Urmia University [Volume 19, Issue 2, 2019, Pages 415-427]
Pirmoradian, M. Dynamic Instability Analysis of Moderately Thick Rectangular Plates Influenced by an Orbiting Mass Based on the First-order Shear Deformation Theory [Volume 19, Issue 9, 2019, Pages 2203-2213]
Pourfallah, M. Numerical Simulation of the Boiling Phenomenon in Improving the Cooling of a Heavy-Duty Diesel Engine with Natural Gas [Volume 19, Issue 2, 2019, Pages 363-373]
Pourhashem, H. Multi-Objective Optimum Design of a Neuro-Fuzzy Network Using a Combined PSO and DE Algorithm Based on Fuzzy Logic [Volume 19, Issue 2, 2019, Pages 475-482]
Pourjafari, M. Longitudinal Free Vibrations of a Rod with Variable Cross-Section Undergoing Finite Strain [Volume 19, Issue 2, 2019, Pages 429-437]
R
Rafati, A. Investigating the effect of construction defects on the Casing Collapse Strength [Volume 19, Issue 12, 2019, Pages 3031-3038]
Rafati, I. Evaluation of Young's Modulus and Poisson's Ratios of Diamond Porous Structure for Use in Orthopedic Implant by Finite Element Method [Volume 19, Issue 5, 2019, Pages 1135-1143]
Rafati Zarkak, M. Numerical Study of Energy Harvesting of Vortex Induced Vibration Phenomenon of Circular Cylinder with Various Sectors at Low Reynolds Number [Volume 19, Issue 7, 2019, Pages 1687-1695]
Rahimi, M. Energy and Exergy Analysis and Optimization of a Multigeneration System by Coupling of GT-MHR Reactor, Absorption Refrigeration, Steam Reforming, and HDH Desalination Cycles [Volume 19, Issue 3, 2019, Pages 631-642]
Rahimi, M.J. Thermodynamic, Economic and Case Study of Synthesis Gas Using the Biomass Gasification Reactor in Distributed Generation Systems [Volume 19, Issue 6, 2019, Pages 1417-1428]
Rahimi, M.R. Experimental Study on the Functionally Graded Ni-P-Al2O3 Coating Created on AA 5xxx Series for Wear Resistance Improvement by Pulse-Electrodeposition Method [Volume 19, Issue 2, 2019, Pages 293-302]
Rahimi, N. Distributed Adaptive Robust Controller Design for Consensus in Multi-Agent System Including Robot Arms with Actuator Saturation Constraint [Volume 19, Issue 7, 2019, Pages 1759-1766]
Rahimian, R. Biomechanical Analysis of Effect of Inclination Angle on Stress Distribution in the Acetabulum and Acetabularcup after Total Hip Arthroplasty [Volume 19, Issue 3, 2019, Pages 559-567]
Rahmani, O. Analytical and Experimental Study of Sandwich Beams with Flexible Core and Composite Facings Reinforced with Carbon Nanotubes [Volume 19, Issue 4, 2019, Pages 801-813]
Rahmani, O. Thermal Effects on Free Vibration of Functionally Graded Curved Timoshenko Nanobeams Resting on WinklerâPasternak Elastic Foundation [Volume 19, Issue 12, 2019, Pages 2865-2875]
Rahmani, S. Analytical Tow-Dimensional Modeling of Blood Flow in a Balloon with Periodic Inflation and Deflation; Application in Intra- and Extra-Aortic Cardiac Assist Devices [Volume 19, Issue 3, 2019, Pages 569-576]
Rahmani, Z. Design and Implementation of Terminal Sliding Mode Controller for Tracking a Wheeled Mobile Robot [Volume 19, Issue 12, 2019, Pages 2887-2894]
Rahmatabadi, D. Characterization of the Plastic and Elastic Properties of Aluminum Sheet Produced by CRB Process via DIC Method [Volume 19, Issue 2, 2019, Pages 505-513]
Rahnama, S. Investigation of Bonding Strength of Steel/Stainless Steel Bimetallic Rod [Volume 19, Issue 1, 2019, Pages 105-113]
Rajabi, M. Self-Activated Acoustical Swimmer and Functionality Comparison with Equivalent Hydrodynamic Swimmers: Spherical Model at Low Reynolds Number Condition [Volume 19, Issue 11, 2019, Pages 2581-2588]
Rajabi, N. Numerical Simulation of Co-Firing of Biomass-Sulfide Concentrate and Pollutants Formation in the Flash Furnace Copper Smelting [Volume 19, Issue 12, 2019, Pages 2927-2934]
Rajabi Zargar Abadi, M. Numerical Simulation of the Sinusoidal Wave Pulsed Film Cooling Effectiveness Due to the Changing Cooling Injection Parameters [Volume 19, Issue 1, 2019, Pages 191-200]
Rajaee, M. Investigating the Effect of Geometric Parameters on Forming AA6063 Cylindrical Step Tubes by Hot Metal Gas Forming Process [Volume 19, Issue 8, 2019, Pages 1865-1873]
Ramazani, H. Influence of Austenitizing Time on Machinability of Ductile Cast Iron with Ferrite-Martensite Dual Phase Matrix [Volume 19, Issue 11, 2019, Pages 2751-2759]
Ramezani, S. A Model to Determining the State of Degradation and Remaining Useful Life of Rotating Equipment, With a New Approach to Combination and Predicting Health Index [Volume 19, Issue 10, 2019, Pages 2351-2365]
Ramezanizadeh, M. Experimental Investigation of Dust Influences on the Airplanes Sound Pressure Emission [Volume 19, Issue 4, 2019, Pages 815-823]
Ramezannejad Azarboni, H. Surface and Magnetic Field Effects Analysis on the Primary and Superharmonic Resonance Frequency Response of Single Walled CNT [Volume 19, Issue 1, 2019, Pages 1-9]
Ramezanzadeh, E. Design and Implementation of Terminal Sliding Mode Controller for Tracking a Wheeled Mobile Robot [Volume 19, Issue 12, 2019, Pages 2887-2894]
Ramiar, A. 1D- 1D Modeling of High Pressure PEM Electrolyzers for Hydrogen Production [Volume 19, Issue 7, 2019, Pages 1663-1674]
Ranjbar Noiey, A. Accessibility to the Geographic Location of Earth's Magnetic Field with Simulation & Data Collection [Volume 19, Issue 8, 2019, Pages 2031-2038]
Rashidi, A.M. Influence of Austenitizing Time on Machinability of Ductile Cast Iron with Ferrite-Martensite Dual Phase Matrix [Volume 19, Issue 11, 2019, Pages 2751-2759]
Rashidi, F. Exergy Analysis and Multiobjective Optimization of Microturbine Based Multigeneration Energy System [Volume 19, Issue 2, 2019, Pages 347-362]
Rashidi, H. Exergy Analysis and Multiobjective Optimization of Microturbine Based Multigeneration Energy System [Volume 19, Issue 2, 2019, Pages 347-362]
Rashidi, H.R. Simulation of Sloshing in Rectangular Tanks under Harmonic Excitation by the Generalized Exponential Basis Functions Meshless Method [Volume 19, Issue 6, 2019, Pages 1397-1408]
Rashidi, S. Fast and Precise Estimation of Displacement and Strain Fields in Elastography Imaging Technique [Volume 19, Issue 2, 2019, Pages 303-315]
Rashvand, M. Stress Analysis and Feasibility of Fabrication of Laminar Ring [Volume 19, Issue 8, 2019, Pages 2039-2046]
Rasoolizadeh Shooroki, A. Effect of Shell Surface Texture Geometry on the Steady State Performance Indexes of Hydrodynamic Journal Bearings [Volume 19, Issue 10, 2019, Pages 2443-2453]
Rastgar, R. Waste Heat Recovery Rankine Cycle Based System for Heavy Duty Trucks [Volume 19, Issue 7, 2019, Pages 1633-1643]
Refahi Oskouei, A. Estimating the Residual Strength of Polyurethane Foam Core Sandwich Panels with Fiber Glass- Polyester Skin Using Acoustic Emission [Volume 19, Issue 3, 2019, Pages 587-596]
Reyahipoor, Me. Modeling the Collapse of Granular Material on a Rigid Wall with Material Point Method (MPM) [Volume 19, Issue 11, 2019, Pages 2626-2634]
Rezaee, M. Investigating the internal resonance and energy exchange between the vibration modes of a cracked beam [Volume 19, Issue 9, 2019, Pages 2139-2148]
Rezaei, S.M. Hysteretic Constitutive Equations Based Continuous Dynamic Modeling of Bending Piezoelectric Actuators [Volume 19, Issue 5, 2019, Pages 1229-1239]
Rezaie, B. Accessibility to the Geographic Location of Earth's Magnetic Field with Simulation & Data Collection [Volume 19, Issue 8, 2019, Pages 2031-2038]
Rezaiefard, H. Numerical Simulation and Parametric Study of an Oscillating Twin-Wing Wind Generator [Volume 19, Issue 5, 2019, Pages 1115-1125]
Rezakazemi, M. Optimization of Combustion Burner at Hoffman Brick Factories [Volume 19, Issue 5, 2019, Pages 1095-1101]
Rezapour, M. Analysis of the Fluid-Thermal Regime with the Developed Brinkman Model in a Porous Coil for Solar Energy Application [Volume 19, Issue 4, 2019, Pages 855-863]
Rezapour Jaghargh, V. Evaluation of Rarefied Shear Flow in Micro/Nano Geometries Using Fokker-Planck Technique [Volume 19, Issue 7, 2019, Pages 1721-1732]
Riahi, A. A Parametric Study on Optical Performance of a Multi-Tubular Solar Reactor by Monte-Carlo ray Tracing Method [Volume 19, Issue 3, 2019, Pages 643-653]
Riahi, M. A Model to Determining the State of Degradation and Remaining Useful Life of Rotating Equipment, With a New Approach to Combination and Predicting Health Index [Volume 19, Issue 10, 2019, Pages 2351-2365]
Roohi, E. Evaluation of Rarefied Shear Flow in Micro/Nano Geometries Using Fokker-Planck Technique [Volume 19, Issue 7, 2019, Pages 1721-1732]
Roohi, H. Investigation on Forming Limit of Aluminum Sheet in Warm Incremental Forming Process [Volume 19, Issue 2, 2019, Pages 259-268]
Roshanian, J. Optimal Landing of Unmanned Aerial Vehicle Using Vectorised High Order Expansions Method [Volume 19, Issue 11, 2019, Pages 2761-2769]
Roshanravan, S. Tracking Controller Design for Polynomial Nonlinear Systems Using Sum of Squares Optimization and Input to State Stability [Volume 19, Issue 6, 2019, Pages 1375-1384]
Rostami Varnousfaaderani, M. Numerical Investigation of Cavitation Effect on the Performance of Waterjet Propulsion System by Computational Fluid Dynamics [Volume 19, Issue 7, 2019, Pages 1779-1788]
Rostamzadeh Khosroshahi, A. Investigation of Geometrical Parameters and Hydrophobic Surfaces on the Performance of Solar Chimney Power Plant [Volume 19, Issue 10, 2019, Pages 2397-2407]
Rouhani Esfahani, E. Experimental Investigation of Machining Parameters of Near Dry Electrical Discharge Machining (EDM) of Mo40 Steel Using Vegetable Oil [Volume 19, Issue 6, 2019, Pages 1539-1549]
Rouhi, S. Evaluation of the Heat Transfer Coefficient of Multi-walled Boron Nitride Nanotubes [Volume 19, Issue 9, 2019, Pages 2105-2110]
Rouhollahi, A. Mechanical Improvement, Simulation, and Implementation of a Visual Servoing Position Controller of a 4-DOF Delta Parallel Robot [Volume 19, Issue 1, 2019, Pages 115-123]
S
Saadat Bakhsh, M. Slip Length of the Nanocomposite Coating in Laminar Flow [Volume 19, Issue 10, 2019, Pages 2463-2469]
Saadatfar, M. Thermoelastic Time-Dependent Creep Analysis of a Rotating Thick-Walled Cylinder Made of Magneto-Electro-Elastic Materials [Volume 19, Issue 11, 2019, Pages 2705-2716]
Sabetghadam, F. Implementation of rigid solid boundaries to the Vorticity-Stream function formulation of incompressible Navier-Stokes equations by time dilation [Volume 19, Issue 5, 2019, Pages 1241-1252]
Sabokrouh, M. Simulation of the Residual Stresses Distribution in Girth Weld of Gas Transmission Pipeline [Volume 19, Issue 1, 2019, Pages 223-228]
Sabokrouh, M. Analysis of Variance of Residual Stress Distribution in Girth Welding of High Strength Low Alloy Steel Gas Pipeline [Volume 19, Issue 7, 2019, Pages 1789-1795]
Sabzpooshani, M. Analytical Investigation of MHD Nanofluid Flow between Non-Parallel Stretching/Shrinking Walls with Considering Joule Heating Effect [Volume 19, Issue 3, 2019, Pages 697-708]
Sadati, S.H. Numerical Study of Aerodynamic Behavior of a Plunging Airfoil in Ground Effect [Volume 19, Issue 3, 2019, Pages 753-763]
Sadati, S.H. Decision-Making System Design for Satellite Temperature Management in the Presence of Fluid Momentum Controller Actuators Fault [Volume 19, Issue 4, 2019, Pages 947-957]
Sadati, S.H. Nonlinear Dynamic Inversion Controller Design for a Satellite, Considering the Dynamics of Magnetorquers [Volume 19, Issue 8, 2019, Pages 1875-1887]
Sadeghian, H. Analysis of Transient Tip-Sample Interactions in High Speed Tapping Mode Atomic Force Microscopy with the Purpose of Damage Prevention [Volume 19, Issue 8, 2019, Pages 1827-1836]
Sadeghi dodaran, R. Effect of Side Looking Acoustic Doppler Velocimeter (ADV) Presence on Turbulent Flow Field in Compound Channel [Volume 19, Issue 12, 2019, Pages 2945-2953]
Sadr, M.H. Development of Boeing-Vertol Dynamic Stall Model Considering Unsteady Flow Effects [Volume 19, Issue 10, 2019, Pages 2559-2569]
Sadri, V. Synthesis of Heat Exchanger Networks with Considering Pressure Drop and Finding Optimized Streams Path Inside Tube and Shell [Volume 19, Issue 5, 2019, Pages 1127-1134]
Saedi, D. 2D Simulation of Red Blood Cell Deformation with Viscoelastic Properties under Ultrasonic Waves [Volume 19, Issue 12, 2019, Pages 3023-3030]
Saeedi, B. Flexural Sensitivity Analysis of Atomic Force Microscope Made of Functionally Graded Materials Based on Modified Couple Stress Theory [Volume 19, Issue 6, 2019, Pages 1457-1466]
Safarabadi Farahani, M. Analytic model for investigation of effect of temperature change on residual stress and curvature of symmetric and un-symmetric composite laminates [Volume 19, Issue 9, 2019, Pages 2155-2164]
Safari, A. Experimental Study of Weld Line Displacement and Drawing Depth in TWBs Steel Sheets Manufactured by Laser and Friction Stir Welding [Volume 19, Issue 9, 2019, Pages 2183-2192]
Safari, M. Investigation on Forming Limit of Aluminum Sheet in Warm Incremental Forming Process [Volume 19, Issue 2, 2019, Pages 259-268]
Safavi, Mohamad Experimental, Numerical, and Analytical Study of a Droplet Impact on Parallel Fibers [Volume 19, Issue 7, 2019, Pages 1645-1653]
Safikhani, H. Technical-Economical Investigation and Comparison of Cooling and Heating Systems in Faculty of Engineering of Arak University [Volume 19, Issue 12, 2019, Pages 2965-2978]
Safikhani, H. Experimental Investigation of Air Pollution in Saveh City and Presenting the Related Solutions to Reduce It [Volume 19, Issue 12, 2019, Pages 2999-3005]
Safipour, H. Numerical Simulation and Parametric Study of an Oscillating Twin-Wing Wind Generator [Volume 19, Issue 5, 2019, Pages 1115-1125]
Safizadeh, M.S. Modeling and Experimental Investigation of Pulsed Eddy Current and Magnetic Saturation for Testing of Ferromagnetic Metals with Sub-surface Pitting [Volume 19, Issue 1, 2019, Pages 143-149]
Saghafian, M. 2D Simulation of Red Blood Cell Deformation with Viscoelastic Properties under Ultrasonic Waves [Volume 19, Issue 12, 2019, Pages 3023-3030]
Saghravani, S.F. Experimental Analysis of Micro- Nano Bubble Formation inside Venturi Tube with High Speed Photography and Image Processing [Volume 19, Issue 12, 2019, Pages 3039-3049]
Sahami, M. 3D Modeling of the Effects of Arrangement and Geometry of the Rod Matrix on the Capturing of Micro-Particles in High Gradient Magnetic Filters [Volume 19, Issue 10, 2019, Pages 2471-2480]
Sahebsara, F. Kinematic Modelling of Origami-Inspired Continuum Robotic Arm by Constant-Curvature Elements [Volume 19, Issue 11, 2019, Pages 2729-2735]
Saidi, M.S. Numerical Analysis of Some Active and Passive Electro-Kinetic Micro-Mixers by Applying Poisson-Nernst-Planck and NavierâStokes (PNP-NSE) Equations [Volume 19, Issue 8, 2019, Pages 2057-2066]
Sajadmanesh, Seyed Morteza Investigating the Separation Bubble Behavior on the Suction Side of a High-Lift Low-Pressure Turbine Blade Using Proper Orthogonal Decomposition [Volume 19, Issue 10, 2019, Pages 2431-2441]
Sajedin, A. Effectiveness of Blade Thickness Distribution on the Turbocharger Turbine Aerostatic Performance [Volume 19, Issue 11, 2019, Pages 2667-2677]
Sajjady, S.A. Invention of a New Ultrasonic Horn in 3D Ultrasonic Vibration Assisted Turning [Volume 19, Issue 8, 2019, Pages 1845-1854]
Salari, H. New Strategy to Simultaneous Increase in Strength and Electrical Conductivity of UFG Copper Strip Fabricated via Accumulative Roll Bonding- Cold Roll Bonding [Volume 19, Issue 9, 2019, Pages 2085-2092]
Salarieh, H. Dynamic modeling and Designing a dynamic based control algorithm for legged quadruped robot locomotion [Volume 19, Issue 11, 2019, Pages 2635-2644]
Salavati, M. Effect of ND: YAG Pulsed Laser Welding Parameters on Microstructural Evolutions and Mechanical Properties of 2205 Duplex Stainless Steel [Volume 19, Issue 10, 2019, Pages 2535-2541]
Salehi, M. An Experimental Investigation on Acoustical Insulation Characteristics of the Natural Rubber Reinforced by Polyester Fibers [Volume 19, Issue 1, 2019, Pages 137-141]
Salehi, M. Feasibility Study of Partially Stratified Charge Mixture Formation and Its Effects on CNG Direct Injection Engine [Volume 19, Issue 10, 2019, Pages 2329-2338]
Salehi neyshaburi, S.A.K. Effect of Side Looking Acoustic Doppler Velocimeter (ADV) Presence on Turbulent Flow Field in Compound Channel [Volume 19, Issue 12, 2019, Pages 2945-2953]
Salehizadeh, S.A.M. Modeling the Collapse of Granular Material on a Rigid Wall with Material Point Method (MPM) [Volume 19, Issue 11, 2019, Pages 2626-2634]
Salehy, S. Efficiency Enhancement of Solar Cells of a Sun Pointing Satellite with Design Optimization of Heat Pipes Configuration Using Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 789-800]
Samadani Aghdam, S.S. Experimental Study of the Effects of Iron Particles Size on Damping Force and Energy Dissipation of a Double-Ended Magnetorheological Damper [Volume 19, Issue 9, 2019, Pages 2129-2138]
Samimi, M.A. Investigation of a new rapid opening valve with fibre optical system for a non-Diaphragm Shock Tube [Volume 19, Issue 5, 2019, Pages 1265-1274]
Sani, M. Numerical Analysis of Some Active and Passive Electro-Kinetic Micro-Mixers by Applying Poisson-Nernst-Planck and NavierâStokes (PNP-NSE) Equations [Volume 19, Issue 8, 2019, Pages 2057-2066]
Sanjari, B. Investigation on the Effect of Guaranteed Selling of Generated Electric Power and Other Effective Parameters on the Application of CHP System in Iranian Industries [Volume 19, Issue 5, 2019, Pages 1221-1227]
Sareban, M.R. Calculating residual stresses by measured released strains using different linear and nonlinear approximations [Volume 19, Issue 3, 2019, Pages 609-620]
Sayahbadkhor, Mostafa Experimental and Numerical Investigating of Failure Factors in One-Way Ring Valves in Reciprocating Compressors [Volume 19, Issue 9, 2019, Pages 2299-2308]
Sedighi, M. An Experimental Investigation on a Modified Friction Assisted Tube Straining Method [Volume 19, Issue 9, 2019, Pages 2079-2084]
Sefid, M. Numerical Study of Mixing Two-Components Non-Newtonian Fluids in Double T-Shaped Micromixers and Multiple T-Shaped with Aligned and Non-Aligned Inputs [Volume 19, Issue 4, 2019, Pages 833-844]
Sefidgar, M. Modeling of Drug Delivery to Solid Tumor with a Remodeled Dynamic Capillary Network Induced by Two Parent Vessels [Volume 19, Issue 12, 2019, Pages 2877-2886]
Sepehrirahnama, Sh. Three-Dimensional Finite Element Modeling of Particle Motion under the Influence of Acoustic Radiation Force in Microchannel [Volume 19, Issue 2, 2019, Pages 483-490]
Seyfi, A. Investigating the Crack Propagation at the Surface of the Composite Patch Bonding to the Steel Substrate [Volume 19, Issue 8, 2019, Pages 1897-1906]
Shabgard, M.R. Numerical and Experimental Investigation of Magnetic Field and Ultrasonic Vibrations Assisted EDM Process [Volume 19, Issue 1, 2019, Pages 159-169]
Shaeri, M.H. Microstructure, Mechanical, and Electrical Properties of Cu-30Zn Alloys Produced by Multi-Directional Forging [Volume 19, Issue 8, 2019, Pages 1943-1952]
Shafaghat, R. 1D- 1D Modeling of High Pressure PEM Electrolyzers for Hydrogen Production [Volume 19, Issue 7, 2019, Pages 1663-1674]
Shafiei, A.R. Modeling the Collapse of Granular Material on a Rigid Wall with Material Point Method (MPM) [Volume 19, Issue 11, 2019, Pages 2626-2634]
Shafiei, M.H. Discrete-Time Control of a Nonlinear System with Integrating the Integral Terminal Sliding Mode and Model Predictive Control [Volume 19, Issue 11, 2019, Pages 2697-2704]
Shafiei Mayam, M.H. Effect of Number of Blades on Performance of an Axial Gas Turbine [Volume 19, Issue 12, 2019, Pages 2907-2916]
Shahbeiki, E. Investigation of Bonding Strength of Steel/Stainless Steel Bimetallic Rod [Volume 19, Issue 1, 2019, Pages 105-113]
Shahmardan, M.M. Simultaneous Numerical Modelling of Heat Transfer and Magnetic Fields in a Vacuum Induction Furnace [Volume 19, Issue 4, 2019, Pages 959-967]
Shahmardan, M.M. Investigation of Magneto-Rheological Fluid Properties inside MR Damper by Use of Dissipative Particle Dynamics Method [Volume 19, Issue 4, 2019, Pages 991-1000]
Shahmardan, M.M. Optimization of Geometric Dimensions of Fire Tube and Heat Coil Used in City Gate Stations Heaters [Volume 19, Issue 5, 2019, Pages 1103-1114]
Shahmirzaloo, A. Characterization of the Plastic and Elastic Properties of Aluminum Sheet Produced by CRB Process via DIC Method [Volume 19, Issue 2, 2019, Pages 505-513]
Shahravi, M. Nonlinear Dynamic Inversion Controller Design for a Satellite, Considering the Dynamics of Magnetorquers [Volume 19, Issue 8, 2019, Pages 1875-1887]
Shahriar, M. Effect of Using Different Gases in Multi-glazed Windows to Reduce Building Heat Losses [Volume 19, Issue 6, 2019, Pages 1409-1416]
Shahriari, B. Onset Yield Analysis of Rotating Variable Thickness Disk Made of Functionally Graded Materials in Engine of Aero Gas Turbine [Volume 19, Issue 9, 2019, Pages 2247-2254]
Shahryari, M. Optimal Layout Design of a Satellite Considering Thermal Control Subsystem Constraints [Volume 19, Issue 8, 2019, Pages 1959-1969]
Shaker Arani, M.J. Dynamic modeling and Designing a dynamic based control algorithm for legged quadruped robot locomotion [Volume 19, Issue 11, 2019, Pages 2635-2644]
Shakeri, M. Predicting Tearing Force for Square Cup Deep Drawing Process by Dimensionless Analysis of the Effective Geometric Parameters [Volume 19, Issue 10, 2019, Pages 2419-2430]
Shakib, S.E. The Energy and Exergy Analysis of a Solid Oxide Fuel Cell and Gas Turbine for Desalination System [Volume 19, Issue 11, 2019, Pages 2737-2749]
Shamaghdari, S. Tracking Controller Design for Polynomial Nonlinear Systems Using Sum of Squares Optimization and Input to State Stability [Volume 19, Issue 6, 2019, Pages 1375-1384]
Shamekhi, A.H. An Improvement in Control-oriented Modeling of SI Engines using Grey-box Structure [Volume 19, Issue 5, 2019, Pages 1283-1295]
Shamekhi, A.M. An Improvement in Control-oriented Modeling of SI Engines using Grey-box Structure [Volume 19, Issue 5, 2019, Pages 1283-1295]
Shams, M. Numerical Simulation of the Effects of Surface Roughness on Nucleation Site Density of Nanofluid Boiling [Volume 19, Issue 7, 2019, Pages 1613-1622]
Shams, Sh. Aeroelastic Analysis of a Double-Sweep Wing with the Metal/Composite Sections [Volume 19, Issue 4, 2019, Pages 927-935]
Shams, Sh. Derivation and Aeroelastic Analysis of a Rotating Airfoil Using Unsteady Loewy Aerodynamic and Flutter Suppression by PID Controller [Volume 19, Issue 6, 2019, Pages 1347-1354]
Shams, Sh. Development of Boeing-Vertol Dynamic Stall Model Considering Unsteady Flow Effects [Volume 19, Issue 10, 2019, Pages 2559-2569]
Sharavi, M. Experimental Measurement of Parameters for High Velocity Impact Simulation on Composite Plate Based On PDM and CZM [Volume 19, Issue 9, 2019, Pages 2215-2226]
Shariati Niasar, M. Waste Heat Recovery Rankine Cycle Based System for Heavy Duty Trucks [Volume 19, Issue 7, 2019, Pages 1633-1643]
Sharifi, B. CFD Simulation of Transit-time Ultrasonic Flowmeter with PZT-5J Piezoelectric Sensor for Light, Heavy, and Medium Crude Oil [Volume 19, Issue 6, 2019, Pages 1337-1346]
Sharifi, N. Numerical Study of Evaporation in a Vertical Porous Channel By the volume of fluid method in OpenFOAM [Volume 19, Issue 2, 2019, Pages 317-326]
Sharifzadeh, F. Controller Design for a Ducted Fan MAV Using Dynamic Inversion Method in Lateral Motion [Volume 19, Issue 6, 2019, Pages 1559-1571]
Sharjerdi, M. Technical-Economical Investigation and Comparison of Cooling and Heating Systems in Faculty of Engineering of Arak University [Volume 19, Issue 12, 2019, Pages 2965-2978]
Shaterian_Alghalandis, V. Investigating the internal resonance and energy exchange between the vibration modes of a cracked beam [Volume 19, Issue 9, 2019, Pages 2139-2148]
Sheikhi, M. Investigation of Micromechanical Behavior of Ferrite and Martensite in Dual Phase Steels [Volume 19, Issue 7, 2019, Pages 1733-1740]
Sheikhi, M. Numerical and experimental investigation of current and electrode force effects on expulsion in resistance spot welding of galvanized and non-galvanized steel sheets [Volume 19, Issue 7, 2019, Pages 1797-1804]
Sheikhi, M. Effect of ND: YAG Pulsed Laser Welding Parameters on Microstructural Evolutions and Mechanical Properties of 2205 Duplex Stainless Steel [Volume 19, Issue 10, 2019, Pages 2535-2541]
Sheikhi, M.M. Design of a basic module for angular motion of spherical joints using the actuators of shape memory alloys and magnetic stabilization system [Volume 19, Issue 2, 2019, Pages 375-386]
Sheikhizad, N. Study of Heat Transfer of Periodic Electroosmotic/Pressure Driven Nanofluid Flow in a Microchannel Using the Poisson-Boltzmann Method [Volume 19, Issue 3, 2019, Pages 765-776]
Sheikhzadeh, Gh.A Numerical Simulation of Nanofluid Heat Transfer in a Tube Equipped with Twisted Tape Using the Eulerian-Lagrangian Two-Phase Model [Volume 19, Issue 1, 2019, Pages 53-62]
Shemirani, F. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Shirvani, M. Experimental and Numerical Study of Effective Parameters on Helical One-channel Dust-concentrator Performance for Separation of Black Powder of Gas Pipeline [Volume 19, Issue 5, 2019, Pages 1167-1176]
Shirzadeh Germi, M. Numerical Investigation of Aeroelastic Behavior of Tall Buildings Considering Wind-Structure Interaction [Volume 19, Issue 3, 2019, Pages 719-730]
Shirzadi, S. Effect of Contact Geometry on the Slip Amplitude and Contact Pressure in Fretting Fatigue of a Turbine Blade Root [Volume 19, Issue 10, 2019, Pages 2409-2418]
Shojaee, T. Postbuckling Analysis of Laminated Composites with Cutout Using Experimental, Numerical, and Finite Strip Methods [Volume 19, Issue 8, 2019, Pages 2067-2077]
Shojaeifard, M.H. Effectiveness of Blade Thickness Distribution on the Turbocharger Turbine Aerostatic Performance [Volume 19, Issue 11, 2019, Pages 2667-2677]
Shokrollahi, S. Determination of Young's Modulus by Finite Element Model Updating [Volume 19, Issue 8, 2019, Pages 1837-1844]
Soheili, M. Effect of Dynamic Parameters and Fluid Impurities on Abrasion of Centrifugal Compressor Impeller of the Gas Transmission Center using Experimental and Analytical Methods [Volume 19, Issue 11, 2019, Pages 2645-2651]
Sokout, M.S. Heart Rate Measurement with Imaging Photoplethysmography Signals Using Smart Phone [Volume 19, Issue 7, 2019, Pages 1751-1757]
Soleimani, A. Analysis of Transient Tip-Sample Interactions in High Speed Tapping Mode Atomic Force Microscopy with the Purpose of Damage Prevention [Volume 19, Issue 8, 2019, Pages 1827-1836]
Soleymani, A. Decision-Making System Design for Satellite Temperature Management in the Presence of Fluid Momentum Controller Actuators Fault [Volume 19, Issue 4, 2019, Pages 947-957]
Soltani, H. Synthesis of Heat Exchanger Networks with Considering Pressure Drop and Finding Optimized Streams Path Inside Tube and Shell [Volume 19, Issue 5, 2019, Pages 1127-1134]
Soroush, M. Experimental Measurement of Parameters for High Velocity Impact Simulation on Composite Plate Based On PDM and CZM [Volume 19, Issue 9, 2019, Pages 2215-2226]
T
Taghavipour, A. Development of a Novel Sizing Software for Plug-In Hybrid Electric Vehicles [Volume 19, Issue 12, 2019, Pages 3051-3062]
Taghiabadi, R. Improving the Mechanical Properties of Mn-rich Al-4Ni-4Mn Alloy by Increasing the Solidification Rate and Friction Stir Processing [Volume 19, Issue 9, 2019, Pages 2175-2182]
Taghirad, H.R. Joint-Space Position Control of a Deployable Cable Driven Robot in Joint Space Using Force Sensors and Actuator Encoders [Volume 19, Issue 11, 2019, Pages 2615-2625]
Taghizadeh, M. Optimal Adaptive High-Order Super Twisting Sliding Mode Control of a Lower Limb Exoskeleton Robot [Volume 19, Issue 3, 2019, Pages 777-787]
Taghizadeh, M. Individual Pitch Angle Robust Control of a Variable Speed Wind Turbine to Mitigate Mechanical Loads [Volume 19, Issue 4, 2019, Pages 937-945]
Taghizadeh, M. Hybrid Active Force Control of Super-Twisting PID Sliding Mode Technique of a Lower Limb Exoskeleton [Volume 19, Issue 12, 2019, Pages 2935-2944]
Taghizadeh Azari, K. Comparative Comparison of Temperature Reduction Solutions in Homeostatic Façade [Volume 19, Issue 8, 2019, Pages 2023-2029]
Taghvaei, H. Effect of Dynamic Stability Derivatives Coefficients on the Design of Operational Parameters of the Actuator in an Underwater Robot [Volume 19, Issue 7, 2019, Pages 1623-1632]
Taghvaeipour, A. Kinematic Modelling of Origami-Inspired Continuum Robotic Arm by Constant-Curvature Elements [Volume 19, Issue 11, 2019, Pages 2729-2735]
Tahani, M. Investigation of Aerodynamic and Heat Transfer Performance of Cylinders Using Plasma Actuators [Volume 19, Issue 9, 2019, Pages 2111-2120]
Taheri, M. Investigation and Sensitivity Analysis of Dimensional Parameters and Velocity in the 3D Nanomanipulation Dynamics of Carbon Nanotubes Using Statistical Sobol Method [Volume 19, Issue 1, 2019, Pages 125-135]
Taheri, M. Second Phase of Nanomanipulation of Particles by Atomic Force Microscopy Using Coulomb, HK, and LuGre Friction Models [Volume 19, Issue 1, 2019, Pages 181-190]
Taheri, M. Air Inlet Angle Effects in Swirling Diffuser of UFAD Systems on Micron Particles Pattern Distribution [Volume 19, Issue 12, 2019, Pages 3083-3093]
Taherinezhad, M. Numerical Analysis of Water Injection Effect on NOx Reduction of MGT-40 Gas Turbine [Volume 19, Issue 2, 2019, Pages 397-405]
Taherzadeh-Fard, A.R. Investigating the Vibrational and Damping Properties of Graphite Nano - Platelet/Epoxy Composites [Volume 19, Issue 9, 2019, Pages 2263-2271]
Talafi Noghni, M. Microstructure, Mechanical, and Electrical Properties of Cu-30Zn Alloys Produced by Multi-Directional Forging [Volume 19, Issue 8, 2019, Pages 1943-1952]
Talebi, Sh. Examining the Performance of New Double L-Shaped Micromixer Type [Volume 19, Issue 4, 2019, Pages 1009-1020]
Tale Masouleh, M. Mechanical Improvement, Simulation, and Implementation of a Visual Servoing Position Controller of a 4-DOF Delta Parallel Robot [Volume 19, Issue 1, 2019, Pages 115-123]
Tale Masouleh, M. Modeling and Experimental Evaluation of Stiffness of a Linear Decoupled 3 Degree of Freedom Parallel Robot [Volume 19, Issue 6, 2019, Pages 1385-1396]
Tale-Masouleh, M. Determination of Optimal Wrench-closure Configuration of Reconfigurable Cable-driven Parallel Robots to Move on a Given Trajectory [Volume 19, Issue 5, 2019, Pages 1085-1093]
Talesh Bahrami, H.R. Numerical Study of the Effect of Flow Suction on the Reduction of Acoustic Noise Due to the Flow on a Three-Dimensional Cylinder [Volume 19, Issue 5, 2019, Pages 1049-1059]
Talezari, M. Efficiency Enhancement of Solar Cells of a Sun Pointing Satellite with Design Optimization of Heat Pipes Configuration Using Genetic Algorithm [Volume 19, Issue 4, 2019, Pages 789-800]
Tavajjohi, M.H. Experimental and Numerical Study of Severe Plastic Deformation in the Constrained Groove Pressing Process on the Pure Copper Sheets [Volume 19, Issue 2, 2019, Pages 269-280]
Tavakol, M.M. Numerical Simulation of Particle Dispersion around Respiratory System of a Standing and Sleeping Mannequin inside a Room [Volume 19, Issue 4, 2019, Pages 877-885]
Tavakoli, M.R. Parametric Study of the Effects of Ice Accretion on the Aerodynamic Performance of NACA0012 Airfoil Using FENSAP-ICE [Volume 19, Issue 9, 2019, Pages 2285-2297]
Tavakoli, T. Ducted wind turbine investigation in a wind tunnel [Volume 19, Issue 5, 2019, Pages 1297-1305]
Teymourtash, A.R. Numerical Study on the Impact of DC Electric Field on Fouling Characteristics of Cross-Flow Filtration [Volume 19, Issue 5, 2019, Pages 1061-1073]
Toghroli, E. Numerical analysis of inclined double pane windows with considering combined natural convection and radiation in filling gas [Volume 19, Issue 9, 2019, Pages 2235-2245]
Torabi, A. Prediction of Weld-Section Geometry in Pulsed Laser Welding Using Different Thermal Models for Thin Stainless Steel Sheets [Volume 19, Issue 8, 2019, Pages 1979-1987]
Torbati, S. Numerical Modeling of Concentric Left Ventricular Hypertrophy of the Human Heart [Volume 19, Issue 10, 2019, Pages 2491-2498]
Torkan, E. Dynamic Instability Analysis of Moderately Thick Rectangular Plates Influenced by an Orbiting Mass Based on the First-order Shear Deformation Theory [Volume 19, Issue 9, 2019, Pages 2203-2213]
Tutunchi, A. Numerical and Experimental Investigation on Boding Strength Optimization of Glass Fibers-Reinforced Epoxy Composites on a Structural Steel Substrate [Volume 19, Issue 2, 2019, Pages 387-396]
U
Usefifar, Gh.R. Numerical and experimental investigation of current and electrode force effects on expulsion in resistance spot welding of galvanized and non-galvanized steel sheets [Volume 19, Issue 7, 2019, Pages 1797-1804]
V
Vaezi, A.A. Study of Microstructure and Mechanical Properties of Dissimilar Friction Welded Martensitic Stainless Steel 410 to Austenitic Stainless Steel 304 [Volume 19, Issue 2, 2019, Pages 439-445]
Vahdat Azad, N. Flutter Analysis of CNT-Reinforced Functionally Graded Composite Wing with Attached Mass [Volume 19, Issue 8, 2019, Pages 1855-1864]
Vahedi, Kh. Numerical and Experimental Study of Oblique Penetration of a Blunt Projectile into Ceramic- Aluminum Target [Volume 19, Issue 5, 2019, Pages 1253-1263]
Valaee Tale, Moslem Numerical and experimental investigation of current and electrode force effects on expulsion in resistance spot welding of galvanized and non-galvanized steel sheets [Volume 19, Issue 7, 2019, Pages 1797-1804]
Varedi-Koulaei, S.M. Design of the Bistable Compliant Four-bar Linkage with Changing the Position of the Flexible Limb [Volume 19, Issue 8, 2019, Pages 2047-2055]
Vatanjou, H. Effects of Dielectric Film Viscoelasticity on Dynamic Behavior of Dielectric Elastomer Minimum Energy Structure [Volume 19, Issue 11, 2019, Pages 2589-2597]
Vatankhah, R. Flexural Sensitivity Analysis of Atomic Force Microscope Made of Functionally Graded Materials Based on Modified Couple Stress Theory [Volume 19, Issue 6, 2019, Pages 1457-1466]
Vatankhah, R. Fuzzy Control for Drug Delivery in Cancerous Tumors Chemotherapy [Volume 19, Issue 6, 2019, Pages 1467-1473]
Veisi Khanghahi, I. Optimal Layout Design of a Satellite Considering Thermal Control Subsystem Constraints [Volume 19, Issue 8, 2019, Pages 1959-1969]
Vesaghati Javan, M. Comparison of Instantaneous Properties Extraction Methods and Execution of Optimal Empirical Mode Decomposition on Faulty Ball Bearing Experimental Data [Volume 19, Issue 7, 2019, Pages 1697-1709]
Y
Yahya Abadi, S. Modification of Mechanical Properties of Al6061 Aluminum Alloy Joint Formed Using Friction Stir Welding by Increasing the Cooling Rate and Application of Vibration [Volume 19, Issue 6, 2019, Pages 1551-1558]
Yahyaei, Sh. Nonlinear Dynamics and Chaotic Behavior in an Oscillator Connected to Shape Memory Alloy [Volume 19, Issue 1, 2019, Pages 95-104]
Yassi, Y. Numerical and Experimental Analysis of Hydro Screw Turbine with Variable Pitch [Volume 19, Issue 2, 2019, Pages 457-466]
Yazdani, A. Effects of the Disk Flexibility on the Flutter and Aeroelastic Response of Mistuned Bladed Disks [Volume 19, Issue 8, 2019, Pages 1907-1916]
Yazdanpanah , M.R. Experimental Study and Simulation of Semi-Constrained Groove Pressing of Interstitial Free Steel Sheet [Volume 19, Issue 11, 2019, Pages 2781-2791]
Yazdanpanah Jahromi, M.A. Simulation and Comparison of the Effect of Oxidizing Gas and Different Devolatilization Models in an Entrained-Flow Coal Gasifier [Volume 19, Issue 12, 2019, Pages 3071-3082]
Yousefi, F. Improving the Mechanical Properties of Mn-rich Al-4Ni-4Mn Alloy by Increasing the Solidification Rate and Friction Stir Processing [Volume 19, Issue 9, 2019, Pages 2175-2182]
Yousefi, J. Investigation the Effect of Loading Rates on Fracture Toughness of Loading Mode I in Glass / Epoxy Composite Laminates by Acoustic Emission [Volume 19, Issue 12, 2019, Pages 2917-2925]
Yousefi, O. Strengthening Defected Dam Gates under Cavitation Vibration Using CFRP [Volume 19, Issue 4, 2019, Pages 825-831]
Yousefi, ُُS. Design and Analysis of a Flexural Hinges Mechanism for Force and Moment Precision Measurement in Wind Tunnel Balance [Volume 19, Issue 9, 2019, Pages 2309-2320]
Z
Zahedzadeh, M. Numerical Study of Step Geometry Effects on Gaseous Sonic Transverse Injection in Supersonic Crossflow [Volume 19, Issue 5, 2019, Pages 1075-1084]
Zakavi, S.J. Study of Ratcheting Behavior of 304L Stainless Steel Branch Pipes by Using Chaboche and Combined Hardening Models [Volume 19, Issue 9, 2019, Pages 2193-2201]
Zakerzadeh, M. Nonlinear Dynamics and Chaotic Behavior in an Oscillator Connected to Shape Memory Alloy [Volume 19, Issue 1, 2019, Pages 95-104]
Zakizadeh, A.M. Estimating the Residual Strength of Polyurethane Foam Core Sandwich Panels with Fiber Glass- Polyester Skin Using Acoustic Emission [Volume 19, Issue 3, 2019, Pages 587-596]
Zamani, H. Modeling of an Evacuated Tube Solar Cooker and Investigation of Weather Parameters Effect [Volume 19, Issue 7, 2019, Pages 1573-1584]
Zamani, J. Experimental Investigation of Air Pollution in Saveh City and Presenting the Related Solutions to Reduce It [Volume 19, Issue 12, 2019, Pages 2999-3005]
Zamani, Jamal Investigation of a new rapid opening valve with fibre optical system for a non-Diaphragm Shock Tube [Volume 19, Issue 5, 2019, Pages 1265-1274]
Zandi, M. Simulation of Sloshing in Rectangular Tanks under Harmonic Excitation by the Generalized Exponential Basis Functions Meshless Method [Volume 19, Issue 6, 2019, Pages 1397-1408]
Zandian, V. Experimental Investigation of Convective Heat Transfer of Ferro-Nanofluid Containing Graphene in a Circular Tube under Magnetic Field [Volume 19, Issue 8, 2019, Pages 1929-1941]
Zare, M. Comparative Comparison of Temperature Reduction Solutions in Homeostatic Façade [Volume 19, Issue 8, 2019, Pages 2023-2029]
Zareei, S.M. Three-Dimensional Finite Element Modeling of Particle Motion under the Influence of Acoustic Radiation Force in Microchannel [Volume 19, Issue 2, 2019, Pages 483-490]
Zarei, B. Second Phase of Nanomanipulation of Particles by Atomic Force Microscopy Using Coulomb, HK, and LuGre Friction Models [Volume 19, Issue 1, 2019, Pages 181-190]
Zarei, Z. Microstructure, Mechanical, and Electrical Properties of Cu-30Zn Alloys Produced by Multi-Directional Forging [Volume 19, Issue 8, 2019, Pages 1943-1952]
Zareinejad, M. Hysteretic Constitutive Equations Based Continuous Dynamic Modeling of Bending Piezoelectric Actuators [Volume 19, Issue 5, 2019, Pages 1229-1239]
Zare Mehrjardi, M. Effect of Shell Surface Texture Geometry on the Steady State Performance Indexes of Hydrodynamic Journal Bearings [Volume 19, Issue 10, 2019, Pages 2443-2453]
Zarifian, P. Flutter of a Circular Cylindrical Shell Subjected to Supersonic External Flow by Considering Internal Fluid Effects through a Novel Formulation [Volume 19, Issue 6, 2019, Pages 1355-1362]
Zarrati, A.R. Effect of Side Looking Acoustic Doppler Velocimeter (ADV) Presence on Turbulent Flow Field in Compound Channel [Volume 19, Issue 12, 2019, Pages 2945-2953]
Zarrinkalam, F. Modeling of an Evacuated Tube Solar Cooker and Investigation of Weather Parameters Effect [Volume 19, Issue 7, 2019, Pages 1573-1584]
Zhaleh Rafati, M. Numerical Analysis of Water Injection Effect on NOx Reduction of MGT-40 Gas Turbine [Volume 19, Issue 2, 2019, Pages 397-405]
Ziaei-Rad, S. Three-Dimensional Finite Element Modeling of Particle Motion under the Influence of Acoustic Radiation Force in Microchannel [Volume 19, Issue 2, 2019, Pages 483-490]
Ziaei-Rad, S. Effect of Fluid and Size on the Nonlinear Dynamic of Atomic Force Microscope Based on Modified Couple Stress Theory [Volume 19, Issue 4, 2019, Pages 1029-1038]
Zirak, S. Numerical Simulation of the Sinusoidal Wave Pulsed Film Cooling Effectiveness Due to the Changing Cooling Injection Parameters [Volume 19, Issue 1, 2019, Pages 191-200]
Zohoori, S. Analytic model for investigation of effect of temperature change on residual stress and curvature of symmetric and un-symmetric composite laminates [Volume 19, Issue 9, 2019, Pages 2155-2164]
Zolatash, S. Fuzzy Control for Drug Delivery in Cancerous Tumors Chemotherapy [Volume 19, Issue 6, 2019, Pages 1467-1473]
Zolfaghari, S.A. Air Inlet Angle Effects in Swirling Diffuser of UFAD Systems on Micron Particles Pattern Distribution [Volume 19, Issue 12, 2019, Pages 3083-3093]
