Volume 19, Issue 6 (June 2019)                   Modares Mechanical Engineering 2019, 19(6): 1529-1538 | Back to browse issues page

XML Persian Abstract Print


1- Mechanical & Aerospace Engineering Department, Malek-e-Ashtar University of Technology, Isfahan, Iran
2- Mechanical Engineering Department, Malek-e-Ashtar University of Technology, Isfahan, Iran , a.kabiri.at@mut-es.ac.ir
Abstract:   (3135 Views)
The preference of fiber–metal laminate over metal and composite in lots of In the present study, the main goal is to investigate an idea for impact resistance improvement of laminates under high-velocity impact by numerical analysis and experiment. Due to the existence of various types of mechanisms for dissipating kinetic energy of projectile in contact with the target, in this research, it has been concentrated on one of them and by adding a rubber layer into AL/GL/GL/AL laminate, it has been allowed more bending to the aluminum layer thereby offering higher dissipating kinetic energy and increased special perforation energy. Materials used in this study are 2024-T3 aluminum alloy, woven glass/epoxy prepreg and Nitrile butadiene rubber (NBR). All of the tests have been done by a high-speed gas gun in Tarbiat Modarres University and numerical analysis is done with Ls Dyna software. With numerical analysis, it is possible to achieve results such as contact force and different energies variations during the impact of the projectile cannot be achieved by The results show that by adding a rubber layer into the laminates, the aluminum layer bend more so more kinetic energy can be dissipated from the projectile. Hence, special perforation energy and ballistic velocity are increased
Full-Text [PDF 735 kb]   (2715 Downloads)    
Article Type: Original Research | Subject: Composites
Received: 2018/05/18 | Accepted: 2018/12/23 | Published: 2019/06/1

References
1. Seyed Yaghoubi A, Liaw B. Thickness influence on ballistic impact behaviors of GLARE 5 fiber-metal laminated beams: Experimental and numerical studies. Composite Structures. 2012;94(8):2585-2598. [Link] [DOI:10.1016/j.compstruct.2012.03.004]
2. Hoo Fatt MS, Lin C, Revilock Jr DM, Hopkins DA. Ballistic impact of GLARE™ fiber-metal laminates. Composite Structures. 2003;61(1-2):73-88. [Link] [DOI:10.1016/S0263-8223(03)00036-9]
3. Zhao G, Cho Ch, Lu Sh, Wang Z. Experimental study on impact resistance properties of T300/epoxy composite laminates. Journal of Composite Materials. 2010;44(7):857-870. [Link] [DOI:10.1177/0021998309346391]
4. Liu Y, Liaw B. Effects of constituents and lay-up configuration on drop-weight tests of fiber-metal laminates. Applied Composite Materials. 2010;17(1):43-62. [Link] [DOI:10.1007/s10443-009-9119-1]
5. Lee DW, Park BJ, Park SY, Choi CH, Song JI. Fabrication of high-stiffness fiber-metal laminates and study of their behavior under low-velocity impact loadings. Composite Structures. 2018;189:61-69. [Link] [DOI:10.1016/j.compstruct.2018.01.044]
6. Sharma AP, Khan SH. Influence of metal layer distribution on the projectiles impact response of glass fiber reinforced aluminum laminates. Polymer Testing. 2018;70:320-347. [Link] [DOI:10.1016/j.polymertesting.2018.07.005]
7. Li X, Zhang X, Guo Y, Shim VP, Yang J, Chai GB. Influence of fiber type on the impact response of titanium-based fiber-metal laminates. International Journal of Impact Engineering. 2018;114:32-42. [Link] [DOI:10.1016/j.ijimpeng.2017.12.011]
8. Mirzababaie Mostofi T, Babaei H, Alitavoli M, Hosseinzadeh S. On dimensionless numbers for predicting large ductile transverse deformation of monolithic and multi-layered metallic square targets struck normally by rigid spherical projectile. Thin Walled Structures. 2017;112:118-124. [Link] [DOI:10.1016/j.tws.2016.12.014]
9. Vlot A, Gunnink JW, editors. Fibre metal laminates: An introduction. Berlin: Springer Science & Business Media; 2011. [Link]
10. Vlot A. Low-velocity impact loading: On fibre reinforced aluminium laminates (ARALL and GLARE) and other aircraft sheet materials [Internet]. Delft: Delft University of Technology; 1993 [cited 15 Jan 2018]. Available from: https://repository.tudelft.nl/islandora/object/uuid:9200a03f-00ab-4c90-8e38-20748dd5fde0 [Link]
11. Lambert JP, Jonas GH. Towards standardization in terminal ballistics testing: Velocity representation [Internet]. Aberdeen: Ballistic Research Laboratory; 1976 [cited 10 Jan 2018]. [Link] [DOI:10.21236/ADA021389]
12. Abdullah MR, Cantwell WJ. The impact resistance of polypropylene-based fibre-metal laminates. Composites Science and Technology. 2006;66(11-12):1682-1693. [Link] [DOI:10.1016/j.compscitech.2005.11.008]
13. Sadighi M, Alderliesten RC, Benedictus R. Impact resistance of fiber-metal laminates: A review. International Journal of Impact Engineering. 2012;49:77-90. [Link] [DOI:10.1016/j.ijimpeng.2012.05.006]
14. Seyed Yaghoubi A, Liaw B. Effect of lay-up orientation on ballistic impact behaviors of GLARE 5 FML beams. International Journal of Impact Engineering. 2013;54:138-148. [Link] [DOI:10.1016/j.ijimpeng.2012.10.007]

Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.