Volume 20, Issue 4 (April 2020)                   Modares Mechanical Engineering 2020, 20(4): 901-913 | Back to browse issues page

XML Persian Abstract Print


1- Mechanical Engineering Faculty, University of Kashan, Kashan, Iran
2- Mechanical Engineering Faculty, Tarbiat Modares University, Tehran, Iran
3- Mechanical Engineering Faculty, University of Kashan, Kashan, Iran , abbasian@kashanu.ac.ir
Abstract:   (2773 Views)
The closed-circuit cooling tower is described as the combination of both wet and dry cooling towers that hot water passes through the bundle of tubes as in the dry cooling towers and surrounding air passes around them in a forced or natural regimes. Thus, secondary water circulates as an open cycle and is sprayed on the bundle of tubes to preserve the tower cooling process. In the present research, the operation of a model of the closed-circuit wet cooling tower has been investigated numerically and experimentally. The effects of environmental condition on process water temperature, sprayed water temperature and air temperature have been evaluated, and the mass and heat transfer coefficients on the surface of hot water tubes have been calculated. According to these results, surrounding air temperature and humidity increasing decreases the tube outer surface mass and heat transfer coefficients. The mass and heat transfer coefficients rates are decreased by about 3% and 4% between the 278 and 288 K and are 6% and 7% between the 288 and 298 K inlet air temperature, respectively. The mass and heat transfer coefficients are both 18% for air inlet temperature between the 298 and 308 K. After 308 K these values are 4%. The decreasing rate of heat and mass transfer coefficient with increasing relative humidity from 10% to 20% is very low and from 20% to 40% is almost constant, and from 40% to 50% a 16% decrease in heat and mass transfer coefficients is observed. 
Full-Text [PDF 840 kb]   (2102 Downloads)    
Article Type: Original Research | Subject: Heat & Mass Transfer
Received: 2019/05/2 | Accepted: 2019/09/16 | Published: 2020/04/17

References
1. Goodman W. The evaporative condenser. Heating Piping Air Conditioning. 1938;10:165-328. [Link]
2. Thomsen EG. Heat transfer in an evaporative condenser. Refrigeration Engineering. 1946;51:425-431. [Link]
3. Wile DD. Evaporative condenser performance factors. Refrigeration Engineering. 1950;58:55-63. [Link]
4. Parker RO, Treybal RE. Heat mass transfer characteristics of evaporative coolers. Chemical Engineering Progress Symposium Series. 1961;57(32):138-149. [Link]
5. Finlay CI, Grant WD. The accuracy of some simple methods of rating evaporative coolers East Kilbride Glasgow: National Engineering Laboratory; 1974. Report No. 584. [Link]
6. Leidenfrost W, Korenic B. Evaporative cooling and heat transfer augmentation related to reduce condenser temperatures. Heat Transfer Engineering. 1982; 3(3-4):38-59. [Link] [DOI:10.1080/01457638108939583]
7. Mizushina T, Ito R, Miyashita H. Characteristics and methods of thermal design of evaporative coolers. Chemical Engineering. 1968;32(1):55-61. [Link] [DOI:10.1252/kakoronbunshu1953.32.55]
8. Tezuka S, Takada T, Kasai S. Performance of an evaporative cooler. Heat Transfer e Japanese Research. 1976;6:1-18. [Link]
9. Finlay CI, Grant WD. Air coolers, cooling towers and evaporative coolers. East Kilbride Glasgow: National Engineering Laboratory; 1972. Report No. 534. [Link]
10. Dreyer AA. Analysis of evaporative cooler and condenser [Dissertation]. Stellenbosch: University of Stellenbosch; 1988. [Link]
11. Webb RL, Villacres A. Algorithms for performance simulation of cooling towers, evaporative condensers and fluid coolers. ASHRAE Transactions. 1984;90 Pt 2B:416-458. [Link]
12. Webb RL. A unified theoretical treatment for thermal analysis of cooling towers, evaporative condensers and fluid coolers. ASHRAE Transactions. 1984;90 Pt 2B:398-415. [Link]
13. Erens J, Dreyer AA. An improved procedure for calculating the performance of evaporative closed circuit coolers. AIChE Symposium Series, Heat Transfer. 1988;84:140-145. [Link]
14. Qureshi BA, Zubair SM. A comprehensive design and rating study of evaporative coolers and condensers. part I. performance evaluation. International Journal of Refrigeration. 2006;29(4):645-658. [Link] [DOI:10.1016/j.ijrefrig.2005.09.014]
15. Qureshi BA, Zubair SM. A comprehensive design and rating study of evaporative coolers and condensers. part II. sensitivity analysis. International Journal of Refrigeration. 2006;29(4):659-668. [Link] [DOI:10.1016/j.ijrefrig.2005.09.015]
16. Zalewski W, Gryglaszewski PA. Mathematical model of heat and mass transfer process in evaporative fluid coolers. Chemical Engineering and Processing: Process Intensification. 1997;36(4):271-280. [Link] [DOI:10.1016/S0255-2701(97)00006-8]
17. Zalewski W, Niezgoda-Zelasko B, Litwin M. Optimization of evaporative fluid coolers. International Journal of Refrigeration. 2000;23(7):553-565. [Link] [DOI:10.1016/S0140-7007(99)00082-1]
18. Gan G, Riffat SB, Shao L, Doherty P. Application of CFD to closed-wet cooling towers. Applied Thermal Engineering. 2001;21(1):79-92. [Link] [DOI:10.1016/S1359-4311(00)00048-X]
19. Gan G, Riffat SB. Numerical simulation of closed wet cooling towers for cooled ceiling systems. Applied Thermal Engineering. 1999;19(12):1279-1296. [Link] [DOI:10.1016/S1359-4311(99)00002-2]
20. Hasan A, Gan G. Simplification of analytical models and incorporation with CFD for the performance of prediction of closed-wet cooling towers. International Journal of Energy Research. 2002;26(13):1161-1174. [Link] [DOI:10.1002/er.842]
21. Xia ZZ, Chen CJ, Wang RZ. Numerical simulation of a closed wet cooling tower with novel design. International Journal of Heat and Mass Transfer. 2011;54(11-12):2367-2374. [Link] [DOI:10.1016/j.ijheatmasstransfer.2011.02.025]
22. Papaefthimiou VD, Rogdakis ED, Koronaki IP, Zannis TC. Thermodynamic study of the effects of ambient air conditions on the thermal performance characteristics of a closed wet cooling tower. Applied Thermal Engineering. 2012;33-34:199-207. [Link] [DOI:10.1016/j.applthermaleng.2011.09.035]
23. Zheng WY, Zhu DS, Song J, Zeng LD, Zhou HJ. Experimental and computational analysis of thermal performance of the oval tube closed wet cooling tower. Applied Thermal Engineering. 2012;35:233-239. [Link] [DOI:10.1016/j.applthermaleng.2011.10.047]
24. Budihardjo B, Nasruddin N, Nugraha MH. Experimental and simulation study on the performance of counter flow closed cooling tower systems. International Journal of Technology. 2015;6(3):365-379. [Link] [DOI:10.14716/ijtech.v6i3.986]
25. Xie X, He C, Xu T, Zhang B, Pan M, Chen Q. Deciphering the thermal and hydraulic performances of closed wet cooling towers with plain, oval and longitudinal fin tubes. Applied Thermal Engineering. 2017;120:203-218. [Link] [DOI:10.1016/j.applthermaleng.2017.03.138]
26. Xie X, He C, Zhang B, Chen Q. Heat transfer enhancement for the coil zone of closed wet cooling towers through field synergy analysis. Computer Aided Chemical Engineering. 2018;44:1927-1932. [Link] [DOI:10.1016/B978-0-444-64241-7.50316-5]
27. Schiller L, Naumann Z. A drag coefficient correlation. Zeitschrift des Vereins Deutscher Ingenieur. 1935;77:318-320. [German] [Link]
28. Ranz WE, Marshall WR. Evaporation from drops, Part I. Chemical Engeeniring Progress. 1952;48(3):141-146. [Link]
29. Jafar FA. Flow fields and heat transfer of liquid falling film on horizontal cylinders [Dissertation]. Melbourne: Victoria University; 2011. [Link]

Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.