Volume 23, Issue 3 (March 2023)                   Modares Mechanical Engineering 2023, 23(3): 191-197 | Back to browse issues page


XML Persian Abstract Print


1- Faculty of materials and manu facturing Technologies, Malek Ashtar university of Technology , m_morakabati@mut.ac.ir
2- Faculty of materials and manu facturing Technologies, Malek Ashtar university of Technology
Abstract:   (1243 Views)
The purpose of this research is to investigate the hot working behavior of the cobalt-nickel base superalloy with the chemical composition of Co-22.8Ni-3.4Al-8Cr-17.1W-1.5Ti-2.8Ta-1.5Nb-1.5Mo-0.06C-0.02B (%wt) by performing compression test, providing the constitutive equation and deformation procssing map and determining the safe and unsafe regions of deformation. In this regard, the hot compression test was performed in the temperature range of 1050-1200 degrees Celsius, with a step of 50 degrees Celsius and strain rates of 0.1, 0.01 and 0.001/s up to a strain of 0.7. The evaluation of the constitutive equations governing the hot deformation process of the superalloy showed that the presented model based on the hyperbolic sine equation predicts the experimental results with acceptable accuracy. Using the mentioned equation, the hot deformation activation energy of the investigated alloy in the present study was obtained as 497 kJ/mol. Based on the process in map drawn for the investigated alloy in the present study, at a strain of 0.4, an instability region was observed at a temperature of 1050 degrees Celsius and a strain rate of 0.01 1/s. the extent and intensity of instability region decreased with the increase in deformation temperature. According to the results of the processing map and the constitutive equations, the optimal conditions of deformation of the investigated alloy are in the temperature range of 1150  to 1200  and the strain rate of 0.1 1/s and the temperature range of 1100  to   1200 and the strain rate of 0.1 to 0.001 the peak efficiency of  45% energy consumption.
Full-Text [PDF 719 kb]   (609 Downloads)    
Article Type: Original Research | Subject: Analysis & Selection of Materials
Received: 2022/08/26 | Accepted: 2023/01/11 | Published: 2023/03/1

References
1. 1) P.J. Bocchini, "Microstructure and Mechanical Properties in Gamma (face-centered cubic)+ Gamma Prime Precipitation-Strengthened Cobalt-based Superalloys." PhD thesis, Northwestern University, 2015.
2. 2) Y. Gu, H. Harada, C. Cui, D. Ping, A. Sato, and J. Fujioka. "New Ni-Co base disk superalloys with higher strength and creep resistance." Scripta materialia 55, 2006, vol.9, pp.815-818. [DOI:10.1016/j.scriptamat.2006.07.008]
3. 3) Xiaokang Zhong, Fusheng Han. "Hot deformation behavior of a new tailored cobalt-based super alloy for turbine discs." Journal of Alloys and Compounds, 2019, vol.599, pp.159-163.
4. 4) Y. Li, Z. Hong, B. Liu, X. Jia, "Investigation of microstructure evolution and mechanical properties of multiprecipitation Co-Ni base superalloys", Materials Science & Engineering A, https://doi.org/10.1016/j.msea.2020.140333 [DOI:10.1016/j.msea.2020.140333., A, vol. 550, pp 333-341, 2021.]
5. 5) R. Kainuma, M. Ise, C.-C. Jia, H. Ohtani and K. Ishida: Intermetallics 4 (1996) S151-S158. [DOI:10.1016/0966-9795(96)00034-9]
6. 6) M.Kolb, L.P.Freund, F.Fischer, I.Povstugar, S.K.Makineni, B.Gault, D.Raabe, J.Müller "On the grain boundary strengthening effect of boron in γ/γ′ Cobalt-base superalloys" Journal of Acta Materialia, Volume 145, Pages 247-254, 15 February 2018. [DOI:10.1016/j.actamat.2017.12.020]
7. 7) A. Suzuki and T. M. Pollock, High-temperature strength and deformation of A. Suzuki and T. M. Pollock, High-temperature strength and deformation of γ/γ′ two-phase Co-Al-W-base alloys vol. 56, 2008 two-phase Co-Al-W-base alloys vol. 56, 2008. [DOI:10.1016/j.actamat.2007.11.014]
8. 8) Y. V. R. K. Prasad, H. L. Gegel, S. M. Doraivelu, J. C. Malas, J. T. Morgan, K. A. Lark, et al., "Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242," Metallurgical Transactions A, vol. 15, pp. 1883-1892, 1984. [DOI:10.1007/BF02664902]
9. 9) T. M. Pollock ,J. Dibbern, M. Tsunekane, J. Zhu, and A. Suzuki, "New Co-based γ/γ′ high-temperature alloys," JOM, vol. 62, pp. 58-63, 2010. [DOI:10.1007/s11837-010-0013-y]
10. 10) R. Ebrahimi and A. Najafizadeh, "A new method for evaluation of friction in bulk metal forming," Journal of Materials Processing Technology, vol. 152, pp. 136-143, 2004. [DOI:10.1016/j.jmatprotec.2004.03.029]
11. 11) Y. V. R. K. Prasad and S. Sasidhara, "Hot Working Guide: A Compendium of Processing Maps," ASM International, 1997.
12. 12) A. Momeni and K. Dehghani, "Characterization of hot deformation behavior of 410 martensitic stainless steel using constitutive equations and processing maps," Materials Science and Engineering: A, vol. 527, pp. 5467-5473, 2010. [DOI:10.1016/j.msea.2010.05.079]
13. 13) Y. V. R. K. Prasad and T. Seshacharyulu, "Processing maps for hot working of titanium alloys," Materials Science and Engineering: A, vol. 243, pp. 82-88, 1998. [DOI:10.1016/S0921-5093(97)00782-X]
14. 14) R. Kainuma, M. Ise, C. C. Jia, H. Ohtani, and K. Ishida, "Phase equilibria and microstructural control in the Ni-Co-Al system," Intermetallics, vol. 4, pp. S151-S158, 1996. [DOI:10.1016/0966-9795(96)00034-9]
15. 15) S. Neumeier, L.P. Freund, M. Göken, Novel wrought γ/γ′ cobalt base superalloys with high strength and improved oxidation resistance, Scripta mater 109 (2015) 104-107 https://doi.org/10.1016/j.scriptamat.2015.07.030 [DOI:10.1016/j.scriptamat.2015.07.030.]
16. 16) E.T. McDevitt, Vacuum induction melting and vacuum arc remelting of Co-Al-WX gamma-prime superalloys, MATEC Web of Conferences ,201402001https://doi. org/10.1051/matecconf/20141402001.
17. 17) S.L. Semiatin, D.S. Weaver, R.C. Kramb, P.N. Fagin, M.G. Glavicic, R.L. Goetz, N.D. Frey, M.M. Antony, Deformation and recrystallization behavior during hot working of a coarse-grain, nickel-base superalloy ingot material, Metall. Mater. Trans. A 35 (2) (2004) 679-693 https://doi.org/10.1007/s11661-004-0379-y [DOI:10.1007/s11661-004-0379-y.]
18. 18) Zhu J., Titus M., Pollock T., Experimental investigation and thermodynamic modeling of the corich region in the Co-Al-Ni-W quaternary system, Journal of Phase Equilibria and Diffusion, 2014, 35(5)595-611. [DOI:10.1007/s11669-014-0327-5]
19. 19) Taheri-Mandarjani, M., Zarei-Hanzaki, A., and Abedi., H. R., "Hot Ductility Behavior of An Extruded 7075 Aluminum Alloy," Materials Science and Engineering: A, Vol. 637, pp. 107-122, 2015. [DOI:10.1016/j.msea.2015.03.038]

Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.