|
مهندسی مکانیک مدرس، جلد ۱۸، شماره ۲، صفحات ۲۲۵-۲۳۳
|
|
|
عنوان فارسی |
ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری |
|
چکیده فارسی مقاله |
در این مقاله به ارزیابی حرارتنگاری مادون قرمز مدولهشده در شناسایی عیوب زیر سطحی مواد مرکب زمینه پلیمری پرداخته شده است. در این روش به منظور تحریک نمونه، شار حرارتی به صورت متناوب به سطح قطعه اعمالشده و پاسخ حرارتی به وسیله تبدیل فوریه پردازش و تصاویر دامنه و فاز استخراج میشوند. پسزمینه غیریکنواخت مشاهدهشده در تصاویر حاصل، اغلب قدرت تشخیص را پایین میآورد لذا برای بهبود ارزیابی این روش، فیلتر آشکارساز لبه و ریختشناسی توصیفی بر روی تصاویر اعمال میگردد. بررسی تجربی در فرکانسهای مختلف بر روی نمونههای ساختهشده با نقصهای کنترلشده رایج در مواد مرکب صورت گرفت. از تحلیل نتایج برای تعیین دقیق موقعیت و ابعاد عیوب استفاده و مشاهده شد که در نمونههای با ضخامت 2 میلیمتر نقص جدایش بین لایهای با حداقل اندازه 20*10 میلی متر و نقصهای الیاف خشک و نفوذ مواد ناخواسته با حداقل اندازه 50*40 میلیمتر شناسایی و اندازهگیری میشوند. در تحلیل اجزای محدود هندسه و عیوب به کار برده شده در آزمون تجربی، در نظر گرفته شد. مشاهده شد که نتایج ارزیابی اجزای محدود با ارزیابی تجربی مطابقت داشته و میتواند در یافتن متغیرهای بهینه در بررسی حرارتنگاری مادون قرمز مدولهشده در عیبیابی مواد مرکب به کار گرفته شود. |
|
کلیدواژههای فارسی مقاله |
آزمون غیر مخرب، حرارت نگاری، مدولاسیون، مواد مرکب |
|
عنوان انگلیسی |
Non-destructive Investigation of Modulated Infrared Thermography in Evaluation of Subsurface Defects in Polymer Matrix Composites |
|
چکیده انگلیسی مقاله |
In this paper, an investigation was done on modulated IR thermography for detection and evaluation of artificial subsurface defects in composite materials. In this method, In order to stimulate the test specimen, the heat flux is applied periodically over the surface of the specimen and the thermal response is decomposed by the Fourier transform method in order to extract its amplitude and phase images. The non-uniform backgrounds in the obtained images often reduce detection ability, In order to improve the evaluation of this method, an edge detection filter and a morphological attribute profile were applied to the images. Experimental investigations were applied for different frequencies on specimens made with common controlled defects in composite materials. Interpretation of the results were utilized in the calculation of defects' size and location, it was observed that in specimen with 2 mm thickness delamination defect with a minimum size of 20*10 mm, dry fiber and inclusion defects with a minimum size of 50*40 mm is detected and is measured. The same geometry and the artificial defects used in experiments, were considered in the finite element analysis. The results of finite element analysis were found to have an agreement with the experimental results and can be used to find the optimum parameters in investigation of modulated IR thermography for detection of defects on composites. |
|
کلیدواژههای انگلیسی مقاله |
Non-destructive test, Thermography, Modulation, Composites |
|
نویسندگان مقاله |
کریم جمالی | karim jamali department of mechanical engineering, tarbiat modares university, tehran, iran گروه مهندسی ساخت و تولید، مهندسی مکانیک، دانشگاه تربیت مدرس، تهران سازمان اصلی تایید شده: دانشگاه تربیت مدرس (Tarbiat modares university)
داود اکبری | davood akbari mechanical engineering-tarbiat modares university استادیار- دانشکده مهندسی مکانیک - دانشگاه تربیت مدرس سازمان اصلی تایید شده: دانشگاه تربیت مدرس (Tarbiat modares university)
محمد گلزار | mohammad golzar department of mechanical engineering, tarbiat modares university, tehran, iran دانشیار دانشگاه تربیت مدرس تهران مدیر گروه مهندسی ساخت وتولید سازمان اصلی تایید شده: دانشگاه تربیت مدرس (Tarbiat modares university)
|
|
نشانی اینترنتی |
http://journals.modares.ac.ir/browse.php?a_code=A-15-27032-1&slc_lang=fa&sid=15 |
فایل مقاله |
فایلی برای مقاله ذخیره نشده است |
کد مقاله (doi) |
|
زبان مقاله منتشر شده |
fa |
موضوعات مقاله منتشر شده |
|
نوع مقاله منتشر شده |
|
|
|
برگشت به:
صفحه اول پایگاه |
نسخه مرتبط |
نشریه مرتبط |
فهرست نشریات
|