Volume 19, Issue 9 (September 2019)                   Modares Mechanical Engineering 2019, 19(9): 2085-2092 | Back to browse issues page

‎ 20.1001.1.10275940.1398.19.9.3.3

XML Persian Abstract Print

Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
Salari H, Mahmoodi M, Borhani E. New Strategy to Simultaneous Increase in Strength and Electrical Conductivity of UFG Copper Strip Fabricated via Accumulative Roll Bonding- Cold Roll Bonding. Modares Mechanical Engineering 2019; 19 (9) :2085-2092
URL: http://mme.modares.ac.ir/article-15-18180-en.html
New Strategy to Simultaneous Increase in Strength and Electrical Conductivity of UFG Copper Strip Fabricated via Accumulative Roll Bonding- Cold Roll Bonding
H. Salari1 , M. Mahmoodi * 2, E. Borhani3
1- Manufacturing & Production Department, Mechanical Engineering Faculty, Semnan University, Semnan, Iran
2- Manufacturing & Production Department, Mechanical Engineering Faculty, Semnan University, Semnan, Iran , mahmoodi@semnan.ac.ir
3- Nanomaterials Department, Nanotechnology Faculty, Semnan University, Semnan, Iran
Abstract:   (7399 Views)

The cold roll bonding (CRB) is a type of bonding process between similar and/or dissimilar metals that is bonded through plastic deformation via rolling process at room temperature. In addition, the accumulative roll bonding (ARB) process is considered as one of the methods for applying severe plastic deformation (SPD) with the ability to achieve ultra-fine grains (UFG) structure and improved mechanical properties. In this research, a combined method was suggested consisting of ARB and CRB processes in order to fabricate UFG copper strip with simultaneous increase of strength and electrical conductivity. Microstructure, mechanical properties, and electrical conductivity of copper specimen fabricated via combined method and ARB processes were investigated. Field emission scanning electron microscope (FESEM) micrographs showed in the crystalline structure of the specimen fabricated via combined method, a large amount of the UFG with uniform distribution are observable. Also tensile strength and hardness of strips increased with increasing the number of rolling passes. Finally, investigation the electrical conductivity of the specimens by four-point probes test showed electrical conductivity decreases with increasing the number of ARB cycles, while the specimen fabricated via combined method increased simultaneously strength, hardness, and high electrical conductivity.

Keywords: Accumulative roll bonding Cold roll bonding Severe plastic deformation Electrical conductivity strength
Full-Text [PDF 1265 kb]   (2261 Downloads)    
Article Type: Original Research | Subject: Metal Forming
Received: 2018/03/26 | Accepted: 2019/01/29 | Published: 2019/09/1
References
1. Xiong L, Shuai J, Liu K, Hou Z, Zhu L, Li W. Enhanced mechanical and electrical properties of super-aligned carbon nanotubes reinforced copper by severe plastic deformation. Composites Part B: Engineering. 2019;160:315-332. [Link] [DOI:10.1016/j.compositesb.2018.10.023]
2. Mahmoodi M, Naderi A, Dini G. Correlation between structural parameters and mechanical properties of Al5083 sheets processed by ECAR. Journal of Materials Engineering and Performance. 2017;26:6022-6027. [Link] [DOI:10.1007/s11665-017-3021-z]
3. Naseri M, Reihanian M, Borhani E. EBSD characterization of nano/ultrafine structured Al/Brass composite produced by severe plastic deformation. Journal of Ultrafine Grained and Nanostructured Materials. 2018;51(2):123-138. [Link]
4. Alizadeh M, Dashtestaninejad MK. Development of Cu-matrix, Al/Mn-reinforced, multilayered composites by accumulative roll bonding (ARB). Journal of Alloys and Compounds. 2018;732:674-682. [Link] [DOI:10.1016/j.jallcom.2017.10.211]
5. Tahmasbi K, Mahmoodi M. Evaluation of microstructure and mechanical properties of aluminum AA7022 produced by friction stir extrusion. Journal of Manufacturing Processes. 2018;32:151-159. [Link] [DOI:10.1016/j.jmapro.2018.02.008]
6. Pirouzi B, Borhani E. Effects of reinforcement distribution on the mechanical properties of Al-Fe3O4 nanocomposites fabricated via accumulative roll bonding. Mechanics of Advanced Composite Structures. 2018;5(2):131-139. [Link]
7. Jiang Sh, Peng R, Jia N, Zhao X, Zuo L. Microstructural and textural evolutions in multilayered Ti/Cu composites processed by accumulative roll bonding. Journal of Materials Science & Technology. 2019;35(6):1165-1174. [Link] [DOI:10.1016/j.jmst.2018.12.018]
8. Mahmoodi M, Lohrasbi S. Investigation of residual stresses distribution in equal channel angular rolled aluminum alloy by means of the slitting method. Journal of Strain Analysis for Engineering Design. 2017;52(6):389-396. [Link] [DOI:10.1177/0309324717715149]
9. Mahmoodi M, Naderi A. Applicability of artificial neural network and nonlinear regression to predict mechanical properties of equal channel angular rolled Al5083 sheets. Latin American Journal of Solids and Structures. 2016;13(8):1515-1525. [Link] [DOI:10.1590/1679-78252154]
10. Honarpisheh M, Haghighat E, Kotobi M. Investigation of residual stress and mechanical propeties of equal channel angular rolled St12 strips. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 2018;232(10):841-851. [Link] [DOI:10.1177/1464420716652436]
11. Mahmoodi M, Sedighi M, Tanner DA. Experimental study of process parameters' effect on surface residual stress magnitudes in equal channel angular rolled aluminum alloys. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 2014;228(12):483-487. [Link] [DOI:10.1177/0954405414522449]
12. Valiev RZ, Langdon TG. Principles of equal-channel angular pressing as a processing tool for grain refinement. Progress in Materials Science. 2006;51(7):881-981. [Link] [DOI:10.1016/j.pmatsci.2006.02.003]
13. Saito Y, Tsuji N, Utsunomia H, Sakai T, Hong R. Ultra-fine grained bulk aluminium produced by accumulative roll bonding process. Scripta Materialia. 1999;40(7):795-800. [Link] [DOI:10.1016/S1359-6462(99)00015-9]
14. Alizadeh M, Talebian M. Fabrication of Al/Cu composite by accumulative roll bonding process and investigation of mechanical properties. Materials Science and Engineering: A. 2012;558:331-337. [Link] [DOI:10.1016/j.msea.2012.08.008]
15. Alizadeh M, Paydar M. Fabrication of nanostructure Al/SiCP composite by accumulative roll-bonding (ARB) process. Journal of Alloys and Compounds. 2010;492(1-2):231-235. [Link] [DOI:10.1016/j.jallcom.2009.12.026]
16. Takata N, Lee SH, Lim CY, Kim SS, Tsuji N. Nanostructured bulk copper fabricated by accumulative roll bonding. Journal of Nanoscience and Nanotechnology. 2007;7(11):3985-3989. [Link] [DOI:10.1166/jnn.2007.073]
17. Hummel R. Electronic properties of materials. 2nd edition. Heidelberg: Springer Verlag GmbH; 1993. pp. 120-123. [Link]
18. Ghalandari L, Moshksar M. High-strength and high-conductive Cu/Ag multilayer produced by ARB. Journal of Alloys and Compounds. 2010;506(1):172-178. [Link] [DOI:10.1016/j.jallcom.2010.06.172]
19. Davis J. ASM specialty handbook: Copper and copper alloys. Russell Township: ASM International Handbook Committee; 2001. p. 44073. [Link]
20. Tsuji N, Saito Y, Lee SH, Minamino Y. ARB (accumulative roll-bonding) and other new techniques to produce bulk ultrafine grained materials. Advanced Engineering Materials. 2003;5(5):338-344. [Link] [DOI:10.1002/adem.200310077]
21. Hansen N, Huang X, Hughes D. Microstructural evolution and hardening parameters. Materials Science and Engineering: A. 2001;317(1-2):3-11. [Link] [DOI:10.1016/S0921-5093(01)01191-1]
22. Hansen N. Hall-petch relation and boundary strengthening. Scripta Materialia. 2004;51(8):801-806. [Link] [DOI:10.1016/j.scriptamat.2004.06.002]
23. Eizadjou M, Danesh Manesh H, Janghorban K. Microstructure and mechanical properties of ultra-fine grains (UFGs) aluminum strips produced by ARB process. Journal of Alloys and Compounds. 2009;474(1-2):406-415. [Link] [DOI:10.1016/j.jallcom.2008.06.161]
24. Smits F. Measurement of sheet resistivities with the four-point probe. Bell Labs Technical Journal. 1958;37(3):711-718. [Link] [DOI:10.1002/j.1538-7305.1958.tb03883.x]
Add your comments about this article : Your username or Email:
CAPTCHA
Send email to the article author

Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.