Volume 19, Issue 11 (November 2019)                   Modares Mechanical Engineering 2019, 19(11): 2645-2651 | Back to browse issues page

XML Persian Abstract Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Keshaverzian H, Jabbari M, Soheili M. Effect of Dynamic Parameters and Fluid Impurities on Abrasion of Centrifugal Compressor Impeller of the Gas Transmission Center using Experimental and Analytical Methods. Modares Mechanical Engineering 2019; 19 (11) :2645-2651
URL: http://mme.modares.ac.ir/article-15-18495-en.html
1- Mechanical Engineering Department, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran
2- Mechanical Engineering Department, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran , jabbari@iaukhsh.ac.ir
Abstract:   (3519 Views)
Abrasion in pipelines and fluid transfer equipment along with impurities in oil and gas and other industrial processes is one of the most important problems of oil, gas and petrochemical industries. Repair of this equipment is considered as one of the major challenges in industry. Wearing was created by the impact of solid particles with gas and liquid particles or by the collision of liquid droplets with the inner wall of the fluid passageway. This research aims to examine the factors affecting the rate of vane wearing including circulation speed of compressor vane, size of particles within methane, density of particles in compounds, angle of incidence and target metal stiffness. To obtain and analyze the rate of vanes' wearing, degraded pieces of vanes' substance were provided and were used as specimen according to the operational conditions, exploitation, and transfer of gas. During the experimental steps, the rate of wearing with varying conditions in solution and solid particles' compounds was measured. According to the results, the speed rate of circulation of centrifugal compressor impeller is an important parameter in increasing efficiency. To obtain this parameter, the mechanical and metallurgical properties of the compressors should have a good quality. Also, considering the relationship with a parabola form, the abrasion increases with increasing the density of particle. The results of the research were compared to the existing standards and theories and the approaches were presented to decrease degradation and wearing in centrifugal compressors' vanes.
Full-Text [PDF 1101 kb]   (1685 Downloads)    
Article Type: Original Research | Subject: Internal Combustion Engine
Received: 2018/04/4 | Accepted: 2019/05/21 | Published: 2019/11/21

References
1. 1- Stachowiak GW, Batchelor AW. Engineering Tribology. Oxford: Butterworth-Heinemann; 2005. [Link]
2. Al-Rikabi ZY. Corrosion lnhibition of carbon steel tubes in cooling system at different sodium salts as function of solution acidity and temperature under low condition [Dissertation]. Baghdad: University of Baghdad; 2003. [Link]
3. Oka YI, Okamura K, Yoshida T. Particle estimation of erosion damage caused by solid particle impact,: Part 1: Effects of impact parameters on a predictive equation. Wear. 2005;259(1-6):95-101. [Link] [DOI:10.1016/j.wear.2005.01.039]
4. Aquaro D. Erosion due to the impact of solid particles of materials resistant at high temperature. Meccanica. 2006;41(5):539-551. [Link] [DOI:10.1007/s11012-006-9002-1]
5. Habib HM, Badr HM, Said SAM, Ben-Mansour R, Al-Anizi SS. Solid-particle erosion in the tube end of the tube sheet of a shell-and-tube heat exchanger. International Journal for Numerical Methods in Fluids. 2006;50(8):885-909. [Link] [DOI:10.1002/fld.1083]
6. Rodríguez E, Flores M, Pérez A, Mercado-Solis RD, González R, Rodríguez J, et al. Erosive wear by silica sand on AISI H13 and 4140 steels. Wear. 2009;26(11):2109-2115. [Link] [DOI:10.1016/j.wear.2009.08.009]
7. Fořt I, Jirout T. The relation between the rate of erosion wear of a pitched blade impeller and its process characteristics. Chemical Engineering Research and Design. 2011;89(10):1929-1937. [Link] [DOI:10.1016/j.cherd.2011.01.024]
8. Mazumder QH. Effect of liquid and gas velocities on magnitude and location of maximum erosion in U-bend. Open Journal of Fluid Dynamics. 2012;2(2):29-34. [Link] [DOI:10.4236/ojfd.2012.22003]
9. Keegan MH, Nash DH, Stack MM. On Erosion issues associated with the leading edge of wind turbine blades. Journal of Physics D: Applied Physics. 2013;46(38). [Link] [DOI:10.1088/0022-3727/46/38/383001]
10. Azimian M, Bart HJ. Investigation of hydroabrasion in slurry pipeline elbows and T-junctions. Journal of Energy and Power Engineering. 2014;8:65-78. [Link] [DOI:10.17265/1934-8975/2014.01.008]
11. Pereira GC, de Souza FJ, de Moro Martins DA. Numerical prediction of the erosion due to particles in elbow. Powder Technology. 2014;261:105-117. [Link] [DOI:10.1016/j.powtec.2014.04.033]
12. Arabnejad H, Mansouri A, Shirazi SA, McLaury BS. Development of mechanistic erosion equation for solid particles. Wear. 2015;332-333:1044-1050. [Link] [DOI:10.1016/j.wear.2015.01.031]
13. Finnie I. Erosion of surface by solid particles. Wear. 1960;3(2):87-103. [Link] [DOI:10.1016/0043-1648(60)90055-7]
14. Bourgoyne Jr AT. Experimental study of erosion in diverter systems due to sand production. SPE/IADC Drilling Conference, 28 February-3 March, New Orleans, Louisiana. New Orleans: Society of Petroleum Engineers; 1989. [Link] [DOI:10.2118/18716-MS]

Add your comments about this article : Your username or Email:
CAPTCHA

Send email to the article author


Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.