Modares Mechanical Engineering

Modares Mechanical Engineering

Mechanical Behavior analysis of Stainless Steel 316L Nanocomposite Reinforcement by Nanoparticles TiC/hBN with 2 & 10 wt.%

Authors
Ali Sadooghi 1
Gholamhasan Payghaneh 2
Mehdi Tajdari 3
1 Department of Mechanical Engineering, Shahid Rajaee University, Tehran, Iran
2 Head Of faculty Of Mechanical Engineering
3 Department of Mechanical Engineering, Arak Branch, Islamic Azad University, Arak, Iran
Abstract
Powder metallurgy process is commonly used to manufacture nanocomposite products, in which the product quality of this process depends upon Composite of reinforcement nanoparticle and distribution. In this article Metal Matrix Nanocomposite (MMN) by powder metallurgy with a base material stainless steel 316L, a material that is widely used in the industry, and reinforcement particles mixture of Carbide Titanium (TiC) as carbon-based reinforcing particles, and Hexagonal Nitride Boron (hBN) particles as the self-lubricating material is prepared. The reinforcement powders were micro Sized and mixed in high ball milling to reach Nano-sized, after 30 h mixing powders in high ball milling reach to Nano-sized, and then reinforcement Nanoparticles with 2 and 10 Wt.% Mixed with stainless steel 316L for 5 hours and compacted at 400 Mpa and sintered at 1400 C temperature and 3 Hours. Scanning electron microscope (SEM), Energy-dispersive X-ray Spectroscopy (EDX) and X-ray Diffraction (XRD) tests are performed on Powders to identify the nanocomposite microstructure. The Mechanical Properties such as Microhardness, Wear, and Bending Strength Were Analyzed. These results Compare with Results of stainless steel 316L without Reinforcement. Microhardness and abrasion resistance of Nanocomposite material have improved and flexural strength improved at the sample with 2 wt.% reinforcement and reduced at the sample with 10 Wt.%.
Keywords
Nanocomposite
Metallurgy Powder
mechanical behavior

Subjects

[1] C. Poole, F. Owens Jr, Introduction to Nanotechnology, vol. 3, A, John Wiley & Sons, Inc. Pub. Hoboken, New Jersy, 2003.
[2] P. M. Ajayan, L. S. Schadler, P. V. Braun, Nanocomposite science and technology: John Wiley & Sons, 2006.
[3] P. H. C. Camargo, K. G. Satyanarayana, F. Wypych, Nanocomposites: synthesis, structure, properties and new application opportunities, Materials Research, Vol. 12, No. 1, pp. 1-39, 2009.
[4] Q. Pham, Y. G. Jeong, S. C. Yoon, S. I. Hong, S. H. Hong, H. S. Kim, Carbon nanotube reinforced metal matrix nanocomposites via equal channel angular pressing, in Proceeding of, Trans Tech Publ, pp. 245-248.
[5] S. Goussous, W. Xu, X. Wu, K. Xia, Al–C nanocomposites consolidated by back pressure equal channel angular pressing, Composites Science and Technology, Vol. 69, No. 11, pp. 1997-2001, 2009.
[6] H. Yu, Processing routes for aluminum based nano-composites, Thesis, worcester polytechnic institute, 2010.
[7] R. Casati, M. Vedani, Metal matrix composites reinforced by nano-particles—a review, Metals, Vol. 4, No. 1, pp. 65-83, 2014.
[8] A. Sanaty-Zadeh, Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall–Petch effect, Materials Science and Engineering: A, Vol. 531, pp. 112-118, 2012.
[9] R. M. German, Powder metallurgy science, Metal Powder Industries Federation, 105 College Rd. E, Princeton, N. J. 08540, U. S. A, 1984. 279, 1984.
[10] C. DellaCorte, H. E. Sliney, Tribological properties of PM212: a high-temperature, self-lubricating, powder metallurgy composite, National Aeronautics and Space Administration, Cleveland, OH (USA). Lewis Research Center, pp. 1989.
[11] Z. Liu, Elevated temperature diffusion self-lubricating mechanisms of a novel cermet sinter with orderly micro-pores, Wear, Vol. 262, No. 5, pp. 600-606, 2007.
[12] J. R. Davis, Stainless steels: ASM international, 1994.
[13] R. Jamaati, M. R. Toroghinejad, High-strength and highly-uniform composite produced by anodizing and accumulative roll bonding processes, Materials & Design, Vol. 31, No. 10, pp. 4816-4822, 2010.
[14] C. Suryanarayana, N. Al-Aqeeli, Mechanically alloyed nanocomposites, Progress in Materials Science, Vol. 58, No. 4, pp. 383-502, 2013.
[15] D. Gay, Composite materials: design and applications: CRC press, 2014.
[16] X. Dangsheng, Lubrication behavior of Ni–Cr-based alloys containing MoS 2 at high temperature, Wear, Vol. 251, No. 1, pp. 1094-1099, 2001.
[17] G. Hammes, R. Schroeder, C. Binder, A. N. Klein, J. D. B. de Mello, Effect of double pressing/double sintering on the sliding wear of self-lubricating sintered composites, Tribology International, Vol. 70, pp. 119-127, 2014.
[18] W. Du Frane, O. Cervantes, G. Ellsworth, J. Kuntz, Consolidation of cubic and hexagonal boron nitride composites, Diamond and Related Materials, Vol. 62, pp. 30-41, 2016.
[19] R. Haubner, M. Wilhelm, R. Weissenbacher, B. Lux, Boron nitrides—properties, synthesis and applications, in: High Performance Non-Oxide Ceramics II, Eds., pp. 1-45: Springer, 2002.
[20] Y.-L. Li, R.-X. Li, J.-X. Zhang, Enhanced mechanical properties of machinable Si 3 N 4/BN composites by spark plasma sintering, Materials Science and Engineering: A, Vol. 483, pp. 207-210, 2008.
[21] C. C. Onuoha, C. Jin, Z. N. Farhat, G. J. Kipouros, K. P. Plucknett, The effects of TiC grain size and steel binder content on the reciprocating wear behaviour of TiC-316L stainless steel cermets, Wear, Vol. 350, pp. 116-129, 2016.
[22] N. Oh, S. Lee, K. Hwang, H. Hong, Characterization of microstructure and tensile fracture behavior in a novel infiltrated TiC–steel composite, Scripta Materialia, Vol. 112, pp. 123-127, 2016.
[23] S. Hu, Y. Zhao, Z. Wang, Y. Li, Q. Jiang, Fabrication of in situ TiC locally reinforced manganese steel matrix composite via combustion synthesis during casting, Materials & Design, Vol. 44, pp. 340-345, 2013.
[24] W. Chen, J. Zhou, Preparation and characterization of stainless steel/TiC nanocomposite particles by ball-milling method, Journal of Wuhan University of Technology--Materials Science Edition, Vol. 24, No. 1, pp. 38-41, 2009.
[25] م. ح. شیرانی, ع. سعیدی, م. کثیری, ا. شیرانی, اثر فعال سازی مکانیکی بر تف جوشی و خواص مکانیکی کامپوزیت Fe-50Ni-TiC, فرآیندهای نوین در مهندسی مواد, Vol. 6, No. 1, pp. 57-62, 2012.
[26] A. Genç, S. Coşkun, M. Öveçoğlu, Microstructural characterizations of Ni activated sintered W–2wt% TiC composites produced via mechanical alloying, Journal of Alloys and Compounds, Vol. 497, No. 1, pp. 80-89, 2010.
[27] J. Li, F. Li, K. Hu, Y. Zhou, TiB 2/TiC nanocomposite powder fabricated via high energy ball milling, Journal of the European Ceramic Society, Vol. 21, No. 16, pp. 2829-2833, 2001.
[28] W. Chen, Y. Gao, C. Chen, J. Xing, Tribological characteristics of Si 3 N 4–hBN ceramic materials sliding against stainless steel without lubrication, Wear, Vol. 269, No. 3, pp. 241-248, 2010.
[29] L. Gao, X. Jin, J. Li, Y. Li, J. Sun, BN/Si 3 N 4 nanocomposite with high strength and good machinability, Materials Science and Engineering: A, Vol. 415, No. 1, pp. 145-148, 2006.
[30] D. Wei, Q. Meng, D. Jia, Mechanical and tribological properties of hot-pressed h-BN/Si 3 N 4 ceramic composites, Ceramics international, Vol. 32, No. 5, pp. 549-554, 2006.
[31] D. R. Petrak, J. D. Lee, Silicon nitride/boron nitride composite with enhanced fracture toughness, Google Patents, 1994.
[32] R. Sachan, J.-W. Park, Formation of nanodispersoids in Fe–Cr–Al/30% TiB 2 composite system during mechanical alloying, Journal of Alloys and Compounds, Vol. 485, No. 1, pp. 724-729, 2009.
[33] I.-J. Shon, S.-L. Du, I.-Y. Ko, T.-W. Kim, J.-M. Doh, J.-K. Yoon, S.-W. Park, Mechanical synthesis and rapid consolidation of a nanocrystalline 5.33 Fe 0.37 Cr 0.16 Al 0.4 Si 0.07–Al 2 O 3 composite by high-frequency induction heating, Ceramics International, Vol. 37, No. 4, pp. 1353-1357, 2011.
[34] I. Manivannan, S. Ranganathan, S. Gopalakannan, S. Suresh, K. Nagakarthigan, R. Jubendradass, Tribological and surface behavior of Silicon carbide reinforced aluminum matrix nanocomposite, Surfaces and Interfaces, 2017.
[35] K. Ramkumar, S. Sivasankaran, A. S. Alaboodi, Effect of alumina content on microstructures, mechanical, wear and machining behavior of Cu-10Zn nanocomposite prepared by mechanical alloying and hot-pressing, Journal of Alloys and Compounds, Vol. 709, pp. 129-141, 2017.
[36] S. Mahathanabodee, T. Palathai, S. Raadnui, R. Tongsri, N. Sombatsompop, Effects of hexagonal boron nitride and sintering temperature on mechanical and tribological properties of SS316L/h-BN composites, Materials & Design, Vol. 46, pp. 588-597, 2013.
Modares Mechanical Engineering
Volume 18, Issue 5
September 2018
Pages 182-191