Modares Mechanical Engineering

Modares Mechanical Engineering

Numerical Investigation of the Effect of Fin Geometry and Film Thickness on Heat Transfer in Falling Film Evaporation on a Horizontal Tube

Document Type : Original Article

Authors
Ali Rahimi
Mohammadhasan Jalaleddin Abyaneh
Farzad Jafarkazemi
Department of Mechanical Engineering, ST.C., Islamic Azad University, Tehran, Iran
10.48311/mme.2026.122000.83058
Abstract
Falling film evaporation is one of the most efficient heat transfer methods in heat exchangers and evaporators. Its performance strongly depends on liquid film hydrodynamics and surface distribution. This study investigated the effect of three circumferential fin geometries on hydrodynamic characteristics and thermal performance of a falling film over a horizontal tube using CFD. Simulations were at Re=217 with VOF two-phase model and constant wall temperature. Liquid volume fraction, film thickness, velocity and temperature fields, and local heat transfer coefficient were extracted at various angles and cross-sections along the tube.

Results showed fin geometry plays a decisive role in redistribution, wettability, and thermal resistance. Model F1 gave the best balance between hydrodynamics and heat transfer. Despite 15.4% higher average film thickness than the smooth tube, it enhanced the heat transfer coefficient by 16.4%. Model F2 showed a 14.9% increase in heat transfer. However, its less uniform distribution caused greater local fluctuations. Model F3, due to accumulation and 69% thicker average film, caused a 74.8% reduction in heat transfer.

A key contribution of this study is the simultaneous assessment of the effects of fin geometry on film distribution and thickness, surface wetting, and heat transfer, thereby elucidating the role of film uniformity in thermal performance. The results demonstrate that increasing the finned surface area or even the average film thickness does not necessarily enhance heat transfer. Instead, uniform film redistribution and the prevention of local liquid accumulation play a more significant role in improving the heat transfer coefficient.
Keywords
Falling film evaporation
Horizontal finned tube
Computational Fluid Dynamics (CFD)
Volume of Fluid (VOF)
Film thickness
Heat transfer coefficient
Subjects
[1] R. Collignon and B. Stutz, “Numerical simulation and modeling of the heat and mass transfer in a grooved flat falling film evaporator,” International Journal of Refrigeration, vol. 146, pp. 148–157, Oct. 2022, doi: 10.1016/j.ijrefrig.2022.10.021.
[2] H.-Y. Lin, M. Muneeshwaran, C.-M. Yang, K. Nawaz, and C.-C. Wang, “On falling film evaporator – A review of mechanisms and critical assessment of correlation on a horizontal tube bundle with updated development,” International Communications in Heat and Mass Transfer, vol. 150, p. 107165, Jan. 2024, doi: 10.1016/j.icheatmasstransfer.2023.107165.
[3] S. M. Ammar and C. W. Park, “Evaporation heat transfer characteristics of falling film in small diameter fabricated tubes of absorption refrigeration system: An experimental investigation,” International Journal of Heat and Mass Transfer, vol. 165, p. 120618, Feb. 2021, doi: 10.1016/j.ijheatmasstransfer.2020.120618.
[4] A. A. Bhuiyan and A. K. M. S. Islam, “Thermal and hydraulic performance of finned-tube heat exchangers under different flow ranges: A review on modeling and experiment,” International Journal of Heat and Mass Transfer, vol. 101, pp. 38–59, Oct. 2016, doi: 10.1016/j.ijheatmasstransfer.2016.05.022.
[5] E. Ya. Gatapova et al., “The temperature jump at water–air interface during evaporation,” International Journal of Heat and Mass Transfer, vol. 104, pp. 800–812, Sept. 2016, doi: 10.1016/j.ijheatmasstransfer.2016.08.111.
[6] C. Cao, L. Xie, X. He, Q. Ji, H. Zhao, and Y. Du, “Numerical study on the flow and heat-transfer characteristics of horizontal finned-tube falling-film evaporation: Effects of liquid column spacing and wettability,” International Journal of Heat and Mass Transfer, vol. 188, p. 122665, 2022, doi: 10.1016/j.ijheatmasstransfer.2022.122665.
[7] Y. Li, M. Li, Y. Li, W. Cai, and L. Yao, “Experimental investigation on the heat transfer performance of falling film evaporation with lubrication oil on horizontal tubes having different structures,” International Journal of Thermal Sciences, vol. 160, p. 106669, Oct. 2020, doi: 10.1016/j.ijthermalsci.2020.106669.
[8] S. Y. Misyura, “Effect of various key factors on the law of droplet evaporation on the heated horizontal wall,” Chemical Engineering Research and Design, vol. 129, pp. 306–313, Nov. 2017, doi: 10.1016/j.cherd.2017.11.033.
[9] M. H. J. Abyaneh, M. H. Saidi, and C. Aghanajafi, “Experimental investigation of aqueous LiBr solution absorber bundle with horizontal elliptical tubes,” HVAC&R Research, vol. 20, no. 2, pp. 251–263, Feb. 2014, doi: 10.1080/10789669.2013.868288.
[10] C.-Y. Zhao et al., “Modelling of evaporative falling-film heat transfer over a horizontal tube,” Applied Thermal Engineering, vol. 255, p. 123997, Jul. 2024, doi: 10.1016/j.applthermaleng.2024.123997.
[11] Q. Wang et al., “Numerical simulation of flow characteristics of falling-film evaporation of R32/R134a non-azeotropic refrigerant outside a horizontal tube,” Applied Thermal Engineering, vol. 236, p. 121724, Oct. 2023, doi: 10.1016/j.applthermaleng.2023.121724.
[12] M. Li, L. Tao, L. Huang, and C. Jin, “Numerical and experimental investigation on condensing heat transfer and flow characteristics outside horizontal dentate-fin tubes,” International Journal of Heat and Mass Transfer, vol. 217, p. 124403, Sept. 2023, doi: 10.1016/j.ijheatmasstransfer.2023.124403.
[13] C.-Y. Zhao, D. Qi, W.-T. Ji, P.-H. Jin, and W.-Q. Tao, “A comprehensive review on computational studies of falling film hydrodynamics and heat transfer on the horizontal tube and tube bundle,” Applied Thermal Engineering, vol. 202, p. 117869, 2022, doi: 10.1016/j.applthermaleng.2021.117869.
[14] W. Zhang, B. Niu, Z. Liu, and Z. Wang, “Numerical investigation on heat transfer enhancement of falling film evaporation by surface structure optimization,” Desalination and Water Treatment, vol. 322, p. 101073, Apr. 2025, doi: 10.1016/j.dwt.2025.101073.
[15] S. Haghayegh, M. H. Saeidi, H. Afshin, M. B. Shafii, and A. Adibnia, “Effects of Evaporator's Length on Pulsating Heat Pipes' Thermal Performance,” Modares Mechanical Engineering, vol. 13, no. 15, pp. 110–115, 2014, doi: 20.1001.1.10275940.1392.13.15.21.1.
[16] B. D. Bock, M. Bucci, C. N. Markides, J. R. Thome, and J. P. Meyer, “Falling film boiling of refrigerants over nanostructured and roughened tubes: Heat transfer, dryout and critical heat flux,” International Journal of Heat and Mass Transfer, vol. 163, p. 120452, 2020, doi: 10.1016/j.ijheatmasstransfer.2020.120452.
[17] M. M. Shah, “Prediction of dryout in evaporation of falling films on horizontal plain tubes,” Chemical Engineering Research and Design, vol. 179, pp. 527–534, 2022, doi: 10.1016/j.cherd.2022.01.039.
[18] T. Zhang, M. Su, C. Zhang, H. Zhang, and B. Dou, “Experimental study on the flow and heat transfer of a horizontal falling film evaporator with spray compensation,” Case Studies in Thermal Engineering, vol. 68, p. 105939, Feb. 2025, doi: 10.1016/j.csite.2025.105939.
[19] M. A. Akhavan Bahabadi and H. Ramazanzadeh, “Augmentation of Heat Transfer During Flow Boiling of R-134a Inside a Tube by Coiled Wire Insert,” Modares Mechanical Engineering, vol. 8, no. 1, pp. 59–68. 2008, doi: 20.1001.1.10275940.1387.8.1.9.6.
[20] A. Karmakar and S. Acharya, “Numerical simulation of falling film sensible heat transfer over round horizontal tubes,” International Journal of Heat and Mass Transfer, vol. 190, p. 122727, 2022, doi: 10.1016/j.ijheatmasstransfer.2022.122727.
[21] Y. Guo, M. Bao, L. Gong, S. Shen, and K. Zhang, “Numerical investigation of the falling film thickness and heat transfer characteristics over horizontal round tube,” International Journal of Multiphase Flow, vol. 149, p. 103977, Jan. 2022, doi: 10.1016/j.ijmultiphaseflow.2022.103977.
[22] C.-Y. Zhao et al., “Correlations of falling film hydrodynamics and heat transfer on horizontal tubes: A review,” Renewable and Sustainable Energy Reviews, vol. 197, p. 114384, Mar. 2024, doi: 10.1016/j.rser.2024.114384.
[23] X. Chen, J. Sheng, T. Lu, J. Wang, K. Zhang, and X. Chen, “Three-dimensional heat transfer coefficient distributions in horizontal tube falling film evaporation,” Applied Thermal Engineering, vol. 216, p. 119141, Nov. 2022, doi: 10.1016/j.applthermaleng.2022.119141.
[24] Y. Tohidi and S. J. Ormiston, “Advanced CFD Modelling of Falling Film Evaporation on a Horizontal Tube using Sharp Interface Tracking,” Journal of Fluid Flow, Heat and Mass Transfer, vol. 12, no. 1, p. 279, Jul. 2025, doi: 10.11159/jffhmt.2025.027.
[25] T. Petrova and R. Dooley, “Revised Release on Surface Tension of Ordinary Water Substance,” Proceedings of the International Association for the Properties of Water and Steam (IAPWS), Moscow, Russia, pp. 23–27, 2014.
[26] C. Cao, L. Xie, Y. Du, X. Zhu, and W. Zhang, “Three-Dimensional Flow Behavior of a Falling Film on Horizontal Tubes: A Comparative Study on Smooth and Finned Tubes,” Industrial & Engineering Chemistry Research, vol. 61, no. 5, pp. 2346–2358, Jan. 2022, doi: 10.1021/acs.iecr.1c04734.
[27] C. W. Hirt and B. D. Nichols, “Volume of Fluid (VOF) Method for the Dynamics of Free Boundaries,” Journal of Computational Physics, vol. 39, no. 1, pp. 201–225, Jan. 1981, doi: 10.1016/0021-9991(81)90145-5.
[28] “A Pressure Iteration Scheme for Two-Phase Flow Modeling,” in Computational Methods for Two-Phase Flow and Particle Transport, pp. 61–82, May 2013, doi: 10.1142/9789814460286_0004.
[29] J. U. Brackbill, D. B. Kothe, and C. Zemach, “A Continuum Method for Modeling Surface Tension,” Journal of Computational Physics, vol. 100, no. 2, pp. 335–354, Jun. 1992, doi: 10.1016/0021-9991(92)90240-Y.
[30] S. Lin, X. Liu, and X. Li, “The Spatial Distribution of Liquid Film Thickness Outside the Horizontal Falling Film Tube,” International Journal of Heat and Mass Transfer, vol. 143, p. 118577, Aug. 2019, doi: 10.1016/j.ijheatmasstransfer.2019.118577.
[31] W. Nusselt, “Die Oberflächenkondensation des Wasserdampfes,” VDI-Zeitschrift, vol. 60, p. 541, 1916.
[32] H. Hao, Q. Bi, H. Ma, and W. Gang, “Distribution characteristics of falling film thickness around a horizontal tube,” Desalination, vol. 285, pp. 393–398, Jan. 2012, doi: 10.1016/j.desal.2011.10.020.
[33] W. H. Parken, L. S. Fletcher, V. Sernas, and J. C. Han, “Heat Transfer Through Falling Film Evaporation and Boiling on Horizontal Tubes,” Journal of Heat Transfer, vol. 112, no. 3, pp. 744–750, Aug. 1990, doi: 10.1115/1.2910449.
Modares Mechanical Engineering
Volume 27, Issue 2
February 2027
Pages 115-138