Modares Mechanical Engineering

Modares Mechanical Engineering

Investigation of the Effect of Loading Rate on the Tensile Behavior of GFRP-Strengthened Steel Pipes under Stepwise Loading

Document Type : Original Article

Authors
1 Mechanical Engineering Department, Arak University of Technology, Arak, Iran
2 Department of Manufacturing and Production, Faculty of Mechanical Engineering, Arak University of Technology, Arak, Iran
10.48311/mme.2026.121701.83050
Abstract
Under actual service conditions, particularly during natural hazards, loads acting on pipelines are often applied rapidly, intermittently, and in successive stages rather than in a uniform and standardized manner.In this study,to simulate this realistic loading pattern, the mechanical behavior of GFRP-strengthened steel pipes subjected to stepwise tensile loading with intermediate holding periods was investigated at loading rates of50, 100, 150,and200 mm/min.The primary objective was to evaluate the effects of loading rate and stepwise loading history on the ultimate joint capacity.The results showed that the maximum shear stresses under stepwise loading at loading rates of50, 100, 150,and200mm/min were5.485, 4.463, 4.724,and 4.424MPa, respectively.Although the overall trend of the results indicates a reduction in ultimate capacity with increasing loading rate, a slight increase in shear stress was observed at150 mm/min compared with that at100 mm/min. Comparison of the different loading stages also showed that the initial stages were the most sensitive to increasing loading rate; in Stage 1, the shear stress at loading rates of100,150, and200 mm/min was55%, 66%,and82% lower, respectively, than that at50 mm/min.Analysis of stress relaxation further showed that the magnitude of stress reduction during the holding periods decreased with increasing loading rate; in Stage1the stress reduction at100, 150, and200mm/min was24%,55%, and70%lower, respectively, than that at50 mm/min.Overall, the results indicate that increasing the loading rate generally leads to a reduction in load-carrying capacity and a decrease in stress reduction during the holding periods, with these effects being more pronounced during the early stages of stepwise loading than during the later stages.
Keywords
Subjects

1-      
[1]      M. Shamsuddoha, M. M. Islam, T. Aravinthan, A. Manalo, and K.-t. Lau, "Effectiveness of using fibre-reinforced polymer composites for underwater steel pipeline repairs," Composite Structures, vol. 100, pp. 40–54, 2013. doi: 10.1016/j.compstruct.2012.12.019
[2]      F. Taheri, "Advanced fiber-reinforced polymer (FRP) composites for the manufacture and rehabilitation of pipes and tanks in the oil and gas industry," in Advanced Fibre-Reinforced Polymer (FRP) Composites for Structural Applications: Elsevier, 2013, pp. 662–704. doi: 10.1533/9780857098641.4.662
[3]      K. Beklemysheva, A. Vasyukov, V. Golubev, and Y. I. Zhuravlev, "On the estimation of seismic resistance of modern composite oil pipeline elements," in Doklady Mathematics, 2018, vol. 97, no. 2: Springer, pp. 184–187. doi: 10.1134/S1064562418020011
[4]      L. T. Popoola, A. S. Grema, G. K. Latinwo, B. Gutti, and A. S. Balogun, "Corrosion problems during oil and gas production and its mitigation," International Journal of Industrial Chemistry, vol. 4, no. 1, p. 35, 2013. doi: 10.1186/2228-5547-4-35
[5]      P. Laney, "Use of composite pipe materials in the transportation of natural gas," INEEL Field Work Proposal, vol. 70, p. 4340, 2002.
[6]      G. O. Edah, J. O. Atiba, and O. S. Fayomi, "Advancements in fibre-reinforced polymers: Properties, applications (A mini review)," Next Materials, vol. 8, p. 100743, 2025. doi: 10.1016/j.nxmate.2025.100743
[7]      K. S. Lim, S. Azraai, N. Noor, and N. Yahaya, "An overview of corroded pipe repair techniques using composite materials," Int. J. Mater. Metall. Eng, vol. 10, no. 1, pp. 19–25, 2016.
[8]      E. Alrehaili, A. Nurdiawati, and S. G. Al-Ghamdi, "Sustainable composites for metal replacement: Environmental assessment and material selection of fiber-reinforced polymer across industries," Resources, Conservation & Recycling Advances, p. 200294, 2025. doi: 10.1016/j.rcradv.2025.200294
[9]      F. G. Alabtah and E. Mahdi, "The effect of sizing optimization on the interface between high strength steel and fiber reinforced composite," Composite Structures, vol. 266, p. 113740, 2021. doi: 10.1016/j.compstruct.2021.113740
[10]    "Sarkhosh R, Farrokhabadi A, Zarei H R. Experimental Investigation of Energy Absorption of Aluminum/ Composite Hybrid Tube Produced by Tape Winding Method under QuasiStatic Load. Modares Mechanical Engineering. 2021; 21(1):55-67.." doi: 20.1001.1.10275940.1399.21.1.6.0
[11]    R. Beyranvand and m. ansari, "Experimental Investigation of the Effect of Tensile Pre Damage and Cyclic Loading on the Flexural Capacity of GFRP Strengthened Steel Pipes under Dry and Wet Environmental Conditions," Modares Mechanical Engineering, pp. –, 2026, doi: 10.48311/mme.2026.119730.82991.
[12]    H. Wang, Q. Zong, and H. Wang, "Research on the tensile mechanical properties and fracture characteristics of GFRP mortar tubes under impact loads," KSCE Journal of Civil Engineering, vol. 28, no. 4, pp. 1367–1378, 2024. doi: 10.1007/s12205-024-0647-x
[13]    J. S. Yuan et al., "Flexural behaviour of concrete-filled pultruded GFRP box beams after exposure to elevated temperatures," Engineering Structures, vol. 357, p. 122497, 2026. doi: 10.1016/j.engstruct.2026.122497
[14]    T. D'Antino and M. A. Pisani, "Use of bending test to determine the tensile strength and elastic modulus of GFRP bars," Composite Structures, vol. 323, p. 117424, 2023. doi: 10.1016/j.compstruct.2023.117424
[15]    M. Noroozolyaee, D. Mostofinejad, A. Saljoughian, and A. Zamanvaziri, "Behavior of square concrete column reinforced with GFRP bars under new reversed cyclic eccentric loading: Experimental and analytical study," Case Studies in Construction Materials, p. e05598, 2025. doi: https://doi.org/10.1016/j.cscm.2025.e05598
[16]    S. Ahankari and A. Patil, "Sea water effect on mechanical performance of steel pipes rehabilitated with glass fiber reinforced epoxy composites," Materials Today: Proceedings, vol. 22, pp. 2490–2498, 2020. doi: 10.1016/j.matpr.2020.03.377
[17]    E. A. Esleman and G. Önal, "Three‐point bending fatigue behavior of basalt‐carbon‐glass/epoxy hybrid composites under saltwater environment," Fatigue & Fracture of Engineering Materials & Structures, vol. 46, no. 7, pp. 2496–2509, 2023. doi: 10.1111/ffe.14012
[18]    H. H. Arifin et al., "Stress distribution analysis of composite repair with Carbon Nanotubes reinforced putty for damaged steel pipeline," International Journal of Pressure Vessels and Piping, vol. 194, p. 104537, 2021. doi: 10.1016/j.ijpvp.2021.104537
[19]    J. M. George, M. Kimiaei, M. Elchalakani, and S. Fawzia, "Experimental and numerical investigation of underwater composite repair with fibre reinforced polymers in corroded tubular offshore structural members under concentric and eccentric axial loads," Engineering Structures, vol. 227, p. 111402, 2021. doi: 10.1016/j.engstruct.2020.111402
[20]    R. Verde, A. D’Amore, and L. Grassia, "A Numerical Model to Predict the Relaxation Phenomena in Thermoset Polymers and Their Effects on Residual Stress during Curing—Part I: A Theoretical Formulation and Numerical Evaluation of Relaxation Phenomena," Polymers, vol. 16, no. 10, p. 1433, 2024. doi: 10.3390/polym16101433
[21]    ""R. Beyranvand and M. Ansari, “Time Dependent Analysis of the Behavior of GFRP-Strengthened Steel Tubes under Stepwise Loading and Stress Relaxation,” Mechanic of Advanced and Smart Materials, vol. 5, no. 1, pp. 146–170, 2025. doi: 10.52547/masm.5.1.146.