Modares Mechanical Engineering

Modares Mechanical Engineering

Layer wise co optimization of infill density and configuration in FDM printed PLA: hierarchical effects on tensile performance

Document Type : Original Article

Authors
1 Amirkabir University of Technology, Department of Mechanical Engineering, Iran
2 Babol Noshirvani University of Technology, Department of Mechanical Engineering, Iran
10.48311/mme.2026.124432.83130
Abstract
Uniform infill strategies overlook how infill density and pattern interact across the thickness of additively manufactured polymer parts. This study examined the mechanical performance of three-zone PLA specimens, with each zone assigned an infill density (30%, 60%, or 90%) and a configuration combining pattern geometry and raster orientation. An L18 Taguchi design guided fabrication, and a general linear model quantified factor contributions. Core density was the dominant predictor of ultimate tensile strength, accounting for 54.7% of the explained variation, while core configuration contributed 7.2% (p < 0.001). Configuration effects depended on density: honeycomb at 0° favored strength at moderate core densities, whereas rectilinear at ±45° improved stiffness at high densities. Abrupt transitions between zones had a smaller, statistically nonsignificant effect, although smoother gradients were qualitatively associated with better strength retention. Segmented specimens exhibited tortuous crack paths and ductile post-yield behavior, unlike the brittle fracture observed in uniform solid references. The best segmented design approached reference tensile strength within 5–13%, while reducing material use by approximately 30% and printing time by 50%. Multiobjective optimization yielded a composite desirability of 0.593. These findings identify core density as the primary design variable for lightweight, functionally graded FDM parts and highlight the importance of separately evaluating pattern geometry and raster orientation.
Keywords
Subjects

[1] M. K. Thompson et al., “Design for additive manufacturing: Trends, opportunities, considerations, and constraints,” CIRP Annals, vol. 65, no. 2, pp. 737–760, 2016, doi: 10.1016/j.cirp.2016.05.004.
[2] I. Gibson, “Rapid prototyping: From product development to medicine and beyond,” Virtual and Physical Prototyping, vol. 1, no. 1, pp. 31–42, 2006, doi: 10.1080/17452750500271298.
[3] A. S. Mazaheri, V. Abedini, and A. Kami, “Effects of raster angle and composition of layers on tensile and flexural properties of PLA-PLA/Al multimaterial manufactured by fused deposition modeling,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 239, no. 1, pp. 213–220, 2025, doi: 10.1177/09544089231175202.
[4] S. M. B. Mirafzali, A. Hasanabadi, and H. Afshari, “Investigating the effect of process parameters on the tensile strength of PLA parts produced by FDM method using the response surface method,” Modares Mechanical Engineering, vol. 22, no. 10, pp. 235–239, 2022.
[5] A. A. Elsonbaty, A. M. Rashad, O. Y. Abass, T. Y. Abdelghany, and A. M. Alfauiomy, “A survey of fused deposition modeling (FDM) technology in 3D printing,” Journal of Engineering Research and Reports, vol. 26, no. 11, pp. 304–312, 2024, doi.: 10.9734/jerr/2024/v26i111332.
[6] A. Cano-Vicent et al., “Fused deposition modelling: Current status, methodology, applications and future prospects,” Additive Manufacturing, vol. 47, Art. no. 102378, 2021, doi: 10.1016/j.addma.2021.102378.
[7] M. V. Ehteshamfar, M. S. Javadi, and H. Adibi, “Surface modification of prototypes in fused deposition modelling using lapping process,” Rapid Prototyping Journal, vol. 28, no. 7, pp. 1382–1393, 2022, doi: 10.1108/RPJ-06-2021-0148.
[8] S. Patel et al., “Effect of infill pattern on the mechanical properties of PLA and ABS specimens prepared by FDM 3D printing,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 240, no. 2, pp. 1759–1767, 2026, doi: 10.1177/09544089241258744.
[9] D. Popescu, A. Zapciu, C. Amza, F. Baciu, and R. Marinescu, “FDM process parameters influence over the mechanical properties of polymer specimens: A review,” Polymer Testing, vol. 69, pp. 157–166, 2018, doi: 10.1016/j.polymertesting.2018.05.020.
[10] M. Kamaal, M. Anas, H. Rastogi, N. Bhardwaj, and A. Rahaman, “Effect of FDM process parameters on mechanical properties of 3D-printed carbon fibre–PLA composite,” Progress in Additive Manufacturing, vol. 6, no. 1, pp. 63–69, 2021, doi: 10.1007/s40964-020-00145-3.
[11] J. K. Sahu, R. K. Sahu, J. K. Katiyar, and P. S. Kiran, “Optimisation of process parameters for dimensional stability in FDM,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, first published online Oct. 17, 2023, doi: 10.1177/09544089231206800.
[12] D. Syrlybayev, B. Zharylkassyn, A. Seisekulova, M. Akhmetov, A. Perveen, and D. Talamona, “Optimisation of strength properties of FDM printed parts—A critical review,” Polymers, vol. 13, no. 10, Art. no. 1587, 2021, doi: 10.3390/polym13101587.
[13] X. Sun, M. Mazur, and C.-T. Cheng, “A review of void reduction strategies in material extrusion-based additive manufacturing,” Additive Manufacturing, vol. 67, Art. no. 103463, 2023, doi: 10.1016/j.addma.2023.103463.
[14] S. K. Prajapati and R. Gnanamoorthy, “Effect of the infill percentage of 3D printed Polyetheretherketone under the dry sliding condition,” Journal of Manufacturing Processes, vol. 131, pp. 2073–2081, 2024, doi: 10.1016/j.jmapro.2024.10.035.
[15] R. A. Mensah, D. A. Edström, O. Lundberg, V. Shanmugam, L. Jiang, X. Qiang, et al., “The effect of infill density on the fire properties of polylactic acid 3D printed parts: A short communication,” Polymer Testing, vol. 111, Art. no. 107594, 2022,  doi: 10.1016/j.polymertesting.2022.107594.
[16] M. Moradi, M. Rezayat, F. A. R. Rozhbiany, S. Meiabadi, G. Casalino, M. Shamsborhan, et al., “Correlation between infill percentages, layer width, and mechanical properties in fused deposition modelling of poly-lactic acid 3D printing,” Machines, vol. 11, no. 10, Art. no. 950, 2023, doi: 10.3390/machines11100950.
[17] H. K. Dave, N. H. Patadiya, A. R. Prajapati, and S. R. Rajpurohit, “Effect of infill pattern and infill density at varying part orientation on tensile properties of fused deposition modeling-printed poly-lactic acid part,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 235, no. 10, pp. 1811–1827, 2021, doi: 10.1177/0954406219856383.
[18] M. R. Khosravani, F. Berto, M. R. Ayatollahi, and T. Reinicke, “Characterization of 3D-printed PLA parts with different raster orientations and printing speeds,” Scientific Reports, vol. 12, Art. no. 1016, 2022, doi: 10.1038/s41598-022-05005-4.
[19] M. T. Birosz and M. Andó, “Effect of infill pattern scaling on mechanical properties of FDM-printed PLA specimens,” Progress in Additive Manufacturing, vol. 9, no. 4, pp. 875–883, 2024, doi: 10.1007/s40964-023-00487-8.
[20] W. Rajhi, A. B. M. Ali, D. J. Jasim, O. Mehrabi, L. Ben Said, and M. Moradi, “Mathematical and statistical analysis of fused filament fabrication parameters for thermoplastic polyurethane parts via response surface methodology,” Mathematics, vol. 12, no. 19, Art. no. 3146, 2024, doi: 10.3390/math12193146.
[21] Z. Malekshahi Beiranvand, H. Abdollahi, N. Salimi, O. Mehrabi, and M. Moradi, “Experimental analysis of 3D-printed carbon fiber-reinforced nylon composites manufactured by fused deposition modeling using a statistical approach,” Journal of Materials Engineering and Performance, vol. 35, pp. 16143–16165, 2026, doi: doi: 10.1007/s11665-025-12783-1.
[22] G. Du, E. Ghanbary, O. Mehrabi, R. Barzamini, and M. Moradi, “Integrating response surface methodology and machine learning for multi-objective optimization of fused deposition modeling parameters in 3D-printed polylactic acid–bronze composites,” Polymer for Advanced Technologies, vol. 37, no. 4, Art. no. e70587, 2026, doi: 10.1002/pat.70587.
[23] R. Sajjad, S. U. Butt, H. A. Saeed, M. T. Anwar, and T. Rasheed, “Impact of multiple infill strategy on the structural strength of single build FDM printed parts,” Journal of Manufacturing Processes, vol. 89, pp. 105–110, 2023, doi: 10.1016/j.jmapro.2023.01.065.
[24] H. Adibi, A. Akbari Lalaei, and A. Nakhaei, “Unified experimental and finite element analysis of the mechanical performance of 3D-printed honeycomb and auxetic sandwich cores,” Composites Part C: Open Access, vol. 18, Art. no. 100656, 2025, doi: 10.1016/j.jcomc.2025.100656.
[25] S. A. Hussain, M. S. Charoo, and M. I. U. Haq, “Mechanical performance of 3D printed functionally graded PETG: An experimental investigation,” Next Materials, vol. 9, Art. no. 101093, 2025, doi: 10.1016/j.nxmate.2025.101093.
[26] International Organization for Standardization, Plastics—Determination of Tensile Properties—Part 2: Test Conditions for Moulding and Extrusion Plastics, ISO 527-2:2012, Geneva, Switzerland: ISO, 2012. (No DOI assigned.)
[27] S. Farah, D. G. Anderson, and R. Langer, “Physical and mechanical properties of PLA, and their functions in widespread applications—A comprehensive review,” Advanced Drug Delivery Reviews, vol. 107, pp. 367–392, 2016, doi: 10.1016/j.addr.2016.06.012.
[28] R. Sajjad, S. U. Butt, K. Mahmood, and H. A. Saeed, “Investigating the impacts of heterogeneous infills on structural strength of 3D printed parts,” Key Engineering Materials, vol. 799, pp. 276–281, 2019 doi: 10.4028/www.scientific.net/KEM.799.276.
[29] H. Safi Valilu, M. A. Saeimi Sadigh, M. Sajed, and V. Tavousi, “Experimental and numerical analysis of energy absorption in 3D-printed auxetic and combined lattice structures under quasi-static loading,” Modares Mechanical Engineering, vol. 25, no. 9, pp. 555–565, 2025, doi: 10.48311/mme.2025.27793.
[30] E. Monaldo, M. Ricci, and S. Marfia, “Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights,” Mechanics of Materials, vol. 177, Art. no. 104551, 2023, doi: 10.1016/j.mechmat.2022.104551.
[31] S. Akhondi, C.-D. Matte, and T. H. Kwok, “A study on mechanical behavior of 3D printed elastomers with various infills and densities,” Manufacturing Letters, vol. 35, suppl., pp. 592–602, 2023, doi: 10.1016/j.mfglet.2023.08.035.
[32] M. Heidari-Rarani, N. Ezati, P. Sadeghi, and M. R. Badrossamay, “Optimization of FDM process parameters for tensile properties of polylactic acid specimens using Taguchi design of experiment method,” Journal of Thermoplastic Composite Materials, vol. 35, no. 12, pp. 2435–2452, 2022, doi: 10.1177/0892705720964560.
[33] B. A. Ahmed, U. Nadeem, A. S. Hakeem, A. Ul-Hamid, M. Y. Khan, M. Younas, et al., “Printing parameter optimization of additive manufactured PLA using Taguchi design of experiment,” Polymers, vol. 15, no. 22, Art. no. 4370, 2023, doi: 10.3390/polym15224370.
[34] R. D. Maalihan, J. C. V. Aggari, A. S. Alon, R. B. Latayan, F. J. P. Montalbo, and A. D. Javier, “On the optimized fused filament fabrication of polylactic acid using multiresponse central composite design and desirability function algorithm,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 240, no. 1, pp. 873–887, 2026, doi: 10.1177/09544089241247454.
[35] A. H. Kadhum, S. Al-Zubaidi, and S. S. Abdulkareem, “Effect of the infill patterns on the mechanical and surface characteristics of 3D printing of PLA, PLA+ and PETG materials,” ChemEngineering, vol. 7, no. 3, Art. no. 46, 2023, doi: 10.3390/chemengineering7030046.