Modares Mechanical Engineering

Volume & Issue: Volume 17, Issue 6, August 2017

Number of Articles: 47

Operational Minimization of Multi-Stage Refrigeration Cyclesâ Power Consumption in Gas Refineries Based on the Combination of Thermodynamics Analysis and Pinch Technology

Pages 1-12

Hossein Kalantar-Neyestanaki; Mostafa Mafi; Ali Ashrafizadeh

Investigation of the effect of mid-tunnel shaft geometry on dispersion of the pollutant in environment

Pages 13-22

Ghassem Heidarinejad; Mozhdeh Shoaei

The effect of wall force field on temperature distribution in nanochannel contains Lennard-Jones fluid by molecular dynamic simulation

Pages 23-31

Ghassem Heidarinejad; Reza Rabani; Ebrahim Shirani

Sizing and topology optimization of spatial truss structures using hybrid algorithm of genetic programing and Nelder-Mead

Pages 32-40

Hirad Assimi; Ali Jamali; Nader Nariman Zadeh

Analytical study the ballistic behavior of thin laminated composite plates based on tsai-hill and maximum strain criterions

Pages 41-50

Ehsan Zamani; Reza Mohammadi Pour; Mohammad Hossein Pol

Effects of chord length, blade pitch angle on hydro kinetic turbineâs power coefficient

Pages 51-58

Mohammad Mehdi Nikoo Hemmat; Iman Khazaei; Arman Mohseni; Seyed Hossein Mohajeri

Schedule Design and Fleet Assignment Based on Modified Intelligent Algorithms

Pages 59-66

Esmaeel Khanmirza; Morteza Haghbeigi; Milad Nazarahari

Prediction of degradation in performance of cathode catalyst layer during load cycling

Pages 67-78

Mahbod Moein Jahromi; Mohammad Jafar Kermani; Saeed Movahed

Numerical simulation of fluid flow penetration through porous media using Lattice Boltzmann method

Pages 79-89

Zafar Namazian; Jafar Namazian

Numerical simulation of inlet vortex near the inlet air duct of an aircraft engine in headwind condition

Pages 90-100

Omid Jahanian; Atiyeh Mihandoust; Hamid Hassanzadeh

Investigation on the effect of bonding time on microstructure and mechanical properties of transient liquid phase bonding between Inconel 718 and Inconel 600

Pages 101-107

Ali Khorram; Akbar Davodi Jamaloei; Abed Jafari; Mahmoud Moradi

Mass and inertia effect of the links on simplification of the 6-PUS robot dynamic equations for different payload ratio

Pages 108-116

Nader Nabavi; Alireza Akbarzadeh Tootoonchi; Javad Enferadi

Experimental Study of Solar Distillation using PCM and Flow Turbulators

Pages 117-127

Mousa Farhadi; Seyed Sharafodin Hosseini; Korosh Sedighi

Analytical investigation of the effect of fibrous tow position and radius on impregnation, pulling force and pressure profile in pultrusion process of thermoplastics

Pages 128-138

Mohamad Hossein Mohammadipour; Mohammad Golzar

Investigation of inertial force effects on the heat transfer of viscoelastic fluid flow inside expanded planar channel with the symmetric abrupt expansion

Pages 139-148

Amin Shahbani Zahiri; Hassan Hassanzadeh; Mohammad Mohsen Shahmardan; Mahmood Norouzi

Numerical study of the effect of angle and distance between hub and shroud at the output passage of impeller in one stage of ESP pump

Pages 149-156

Mahdi Hoseiniparast; Behzad Ghadiri; Saleh Fallah

Optimal Multiple-Burn Injection of a Satellite into Geostationary orbit Using an Upper Stage

Pages 157-167

Mojtaba Alavipour; Amirali Nikkhah; Jafar Roshanian

Nonlinear Control of Air path in a Turbocharged Diesel Engine Using Optimization

Pages 168-178

Ahmad Assasi; Mehdi Mirzaei; Rahim Khoshbakhti Saray

Model Predictive and Adaptive Controller Design of Tri-Tilt Rotor VTOL UAV by Using Multi-Body Modeling

Pages 179-189

masoud alizadeh; mehrdad ebrahimi dormiani; Mahdi Noori Dabir

Design of Spike Nozzle and Comparison of Turbulence Models in Numerical Simulation of its Flow-field in Design and Off-design Conditions

Pages 190-200

Mohammad Mahdi Heydary; Ismael Valizadeh; Mustafa Rezvandoost

Investigation of the Tracheobronchial Cartilages Effect on the Respiration by hybrid RANS-LES Approach

Pages 201-2012

Ghasem Heidarinejad; Mohammad Hosein Roozbahani

Design and fabrication of an autonomous mobile robot equiped with color lasers and its trajectory control based on machine vision

Pages 213-220

Saeed Khodaei; Akbar Allahverdizadeh; Behnam Dadashzadeh

Design and implementation of AHRS by using Kautz function and predictive estimator with Eulerâs dynamic

Pages 221-232

Hamid Vosoughi; Jafar Keighobadi; Javad Faraji

Investigation of Temperature Field and Laminar Flame Structure of Inclined Impinging Jets by Interferometry Mach-Zehnder Experimental Method

Pages 233-240

Mehrdad Kiani; Paria Amiri; Kazem Esmailpour

The effect of workpiece hardness and cutting parameters on surface roughness in dry hard turning of X210Cr12 cold tool steel

Pages 241-247

Behbood Heydari; Mohammad Mahdi Abootorabi Zarchi; Hamid Reza Karimi zarchi

Modelling Wheel Motion in order to prevent Slipping as it Braking: Using Classic Models and FEM

Pages 248-256

Majid Shahravi; najafali heidari

Combination of independent component analysis and support vector machines for intelligent faults diagnosis of rotating machinery

Pages 257-264

Mohammad hadi Ghafari; Afshin Ghanbarzadeh; Ali Valipour

Numerical study of the performance of an oscillating wave surge converter using volume of fluid method

Pages 265-276

Hamid Reza Mottahedi; Morteza Anbarsooz; Mohammad Pasandideh-Fard

Introducing a novel slip boundary condition for the compressible gas flow through a micro/nano channel

Pages 277-285

masoud akbari; majid ghasemi

Observer-Based Robust Adaptive Fuzzy Approach for Current Control of Robot Manipulators by Estimation of Uncertainties

Pages 286-294

Hesam Fallah Ghavidel; Ali Akbarzadeh Kalat; Vahid Ghorbani

Modeling and position controller design of a servo-hydraulic actuator under variable loads using sliding mode control

Pages 295-302

vahid hassany; mostafa taghizadeh; mahmood mazare

Real Time Direct Kinematics Solution of 3-RPS Parallel Robot Using a Semi-Analytical Homotopy Method

Pages 303-310

Milad Shafiee Ashtiani; Aghil Yousefi-Koma; Hossein Keshavarz; S. Mojtaba Varedi Koulaie

The effects of laser pulse energy and focal point position on laser surface hardening of AISI 410 stainless steel

Pages 311-318

Mahmoud Moradi; Mojtaba Karami Moghadam; Jalal Zarei; Behnam Ganji

The use of the differential quadrature method in the analysis of composite metal cylindrical vessel under dynamical load

Pages 319-330

Ali Asghar Masoumi; Gholam Hossein Rahimi; Gholam Hosain Liaghat

Geometry and Zeta Potential Effects on Electroosmotic Mixing in Converging (Diverging) Microchannel using Lattice Boltzmann Method

Pages 331-341

Yaser Basati; Omid Reza Mohammadipour; Hamid Niazmand

Experimental analysis of spot welded parameters on tensile behavior of ferrite-martensite dual phase steel with Taguchi statistical method

Pages 342-350

Hamid Reza Ghanbari; mahmoud shariati

Trajectory and control design of a quadcopter for crossing obstacles using sliding mode method

Pages 351-356

Abdolmajid Khoshnood; Fatemeh Khajemohammadi; Seyed Sina Zehtabchi

Real-time estimation of micro-milling cutting tool deflections by using signals of stages driven by linear motors

Pages 357-364

Mohammad Sadegh Heydarzadeh; Seyed Mehdi Rezaei; Noor Azizi Bin Mardi; Ali Kamali

Investigation of the effective parameters in the bulging process and obtaining Forming limit curve of the stainless steel tube by the GTN criterion

Pages 365-376

Maryam Geran Gharakheyli; Hamid Gorji; Mohammad Bakhshi; Mohammad Javad Mirnia

A Modification in the Decoupled Natural Orthogonal Complement Method, Using Virtual Spring Concepts

Pages 377-384

Ali Raoofian; Afshin Taghvaeipour; Ali Kamali Eigoli

Physical modeling of melt flow in steel continuous casting tundish

Pages 385-392

Mohamad Reza Mosalman Yazdi; Ahmad Reza Faghih Khorasani; Shahram Talebi

Free and forced convectional heat transfer analysis of rectangular porous fin with Differential transformation method

Pages 393-400

Salman Nourazar; Mohammadreza mohammadpour

Theoretical, numerical and experimental analysis of a planar wobble motor driven by shape memory alloy (SMA)wires

Pages 401-412

Bahman Mirzakhani; Mohammad Abbasi; Mehdi Modabberifar; Yousef Payandeh

Continuous Time Discrete State Markovian Approach for Reliability Assessment of Missile System During its Life Cycle

Pages 413-422

Vahid Marefat

Prediction of fluid flow through U-bend channels using linear and nonlinear models of turbulence.

Pages 423-432

Mohammad Vaezi; Mehrdad Raisee

study of a direct-expansion ground source heat pump using carbon dioxide

Pages 433-443

Hossein Ghazizade-Ahsaee; Mehran Ameri

Developing a novel soft magnetic force sensor based on Hall Effect

Pages 444-450

Hossein Mirzanejad; Ashkan Fathian; Mohammad Mojarrabi Tabrizi; Ali Sharifnejad; Mohammad Mahdi Agheli Haji Abadi

Journal Archive

Volume 25 (2024)

Volume 24 (2023)

Volume 23 (2022)

Volume 22 (2021)

Volume 21 (2021)

Volume 20 (2020)

Volume 19 (2019)

Volume 18 (2018)

Volume 17 (2017)

Volume 16 (2016)

Volume 15 (2015)

Volume 14 (2014)

Volume 13 (2013)

Volume 12 (2012)

Volume 11 (2011)

Volume 10 (2010)

Volume 9 (2009)

Volume 8 (2008)

Volume 7 (2007)

Volume 6 (2006)

Volume 1 (2001)