Modares Mechanical Engineering

Volume & Issue: Volume 15, Issue 3, May 2015

Number of Articles: 44

Experimental analysis of tensile strength of lateral notched aluminum plates reinforced by the Fiber metal laminate (FML) patches

Pages 1-8

Faramarz Ashenai Ghasemi, Gholam Reza Bagheri, Ali Pourkamali

Type Synthesis of 3T1R Decoupled Parallel Manipulators based on Screw Theory

Pages 9-18

Hamid Reza Mohammadi, Roghaye Hasanzadeh

Thermal stress analysis of metallic plate with quasi-rectangular hole

Pages 19-26

Mohammad Jafari, Mohammad Bagher Nazari, Amir Taheri Nasab

Forced vibration analysis of conveying fluid carbon nanotube resting on elastic foundation based on modified couple stress theory

Pages 27-34

Reza Ansari, Amir Norouzzadeh, Raheb Gholami

Effects of air curtainâs jet discharge angle on indoor air quality and occupantsâ thermal comfort in a positive pressure room

Pages 35-41

Seyed Alireza Zolfaghari, Ali Barati Majan

fatigue crack growth in bodies under rolling contact with multiple moving loads

Pages 42-52

Amir Reza Shahani, Reza Davachi

Simulation of a turbocharged SI engine to investigate autoignition, knock onset and flame propagation by using Kiva code

Pages 53-62

Ali Nasiri Tossi, Arman Rostampour

Suitable parameters determination of lamb wave generation source with low-attenuation for three-layer adhesive joints inspection

Pages 63-74

Pezhman Taghipour Birgani, Khosro Naderan Tahan, Sina Sodagar, Mohammad Shishesaz

Design and manufacturing of modified Iosipesque shear test fixture for determine the in layered composite properties

Pages 75-83

Mohammad Reza Variri Sereshk, Ali Reza Araee, Ahmad Reza Farokhi, Nabi Mehri Khansari

Contact Angle Comparison of Droplet Impact on Solid Surface Using VOF

Pages 84-94

Sahar Jafari, Mohammad Reza Ansari, Nima Sam Khaniani

Effects of interphase damage on the elastoviscoplastic behavior of general unidirectional metal matrix composites

Pages 95-105

MohammadJavad Mahmoodi, Mohammad Kazem Hassanzadeh, Reza Ansari

Experimental study of finishing of AISI H13 hot work steel using Abrasive Flow Finishing (AFF) process

Pages 106-112

Mohammad Reza Shabgard, Behnam Karamzadeh, Reza Alizadegan, Ahad Gholipoor

2D Local Imperfect plate Non-linear Vibration and Aerothermoelastic analysis in Supersonic Flow

Pages 113-124

Hamid Moosazadeh, Behzad Ghadiri, Masoud Rasekh

Experimental and Numerical Study of a Variable-Span-sweep Morphing Wing on the Aerodynamic Characteristics of a UAV

Pages 125-136

Abbas Tarabi, Saajad Gasemloo, Mahmood Mani

Controllable Workspace Generation for a Cable-Driven Rehabilitation Robot using Neural Network and based on patientâs Anthropometric Parameters

Pages 137-145

Behnam Miripour Fard, Tahereh Padargani

Active Noise Cancelation in a Reaction Wheel by simultaneous using of dynamical system identification and online wavelet

Pages 146-152

Habib Khaksari, Abdolmajid Khoshnood, Jafar Roshanian

Dynamic instability in tapered beams under wind excitation

Pages 153-161

Hamid Moeenfard, Behnam Moetakef Imani, Morteza Davoudi, Amin Rahimzadeh

An upper bound analysis of the geometric shape of the deformation zone in drawing process of the metal plates through wedge-shaped die

Pages 162-172

Seyed Hooman Kazemi, Heshmatollah Haghighat

Instantaneous Center of Rotation of Flexure Joints and Velocity Kinematic Analysis of Microhexapod Using Screw Theory

Pages 173-180

Ehsan Rouhani Esfahani, Mohammad Javad Nategh

Study of the causes of excessive vibrations in air fans and proposing practical solutions for decreasing the vibration level

Pages 181-188

Mohamad Hasan Mazhab Jafari, Ali Hajnayeb, Gholam-hossein Massoumi

Numerical study of the effect of moistureâinduced swelling stresses on damage behavior of adhesive joints under static loading

Pages 189-198

Zahra Abbasi, Hadi Khoramishad

Estimation of a centrifugal pump slip factors at off-design conditions using computational fluid dynamics

Pages 199-207

Mohsen Ghaderi, Amir Farhad Najafi, Ahmad Nourbakhsh

Investigation of MHD nano-fluid flow over a stretching surface with velocity slip and convective surface boundary conditions

Pages 208-218

Navid Freidoonimehr, Asghar Baradaran Rahimi

Burning rate Measurement of solid Propellant using Subscale Motors

Pages 219-230

Mohammad Reza Ghelichkhani, Ali Reza Mohammadi, Mohammad Mahdi Heidari

Numerical investigation of flow and temperature field on the backward-facing step affected by Electrohydrodynamic actuator

Pages 231-238

Kamran Kamran Mostajiri Abid, Nima Amanifard, Hamed Mohaddes Deylami

Experimental Analysis and Simulation of Temperature Contour Generated in the Welding Process of Electrofusion Tapping Saddle Polyethylene Gas Pipes and Relevant Temperature Estimation for Fitting

Pages 239-242

Ali Ebrahimpour, Nosratollah Solhjoei, Ebrahim Mohseni Homagerani, Meysam Rasooly, Arash Karimipour

Effect of porosity on microstructure and mechanical properties of Al2O3(p)/Al-A356 MMC

Pages 243-250

Esmaeil Damavandi, Salman Nourouzi, Sayed Mahmood Rabiee

Evaluation of radial expansion behavior of thick-walled cylinder under internal explosive loading with numerical analysis

Pages 251-259

Seyed Masoud Bagheri, Jamal Zamani

Numerical Investigation of Electro-osmotic Flow in Heterogeneous Microchannels

Pages 260-270

Jafar Jamaati, Ali Reza Farahinia, Hamid Niazmand

Free vibration analysis of FG-CNTRC cylindrical shells surrounded by elastic foundation subjected to thermal loading

Pages 271-282

Reza Ansari, Jalal Torabi

An experimental investigation on mode-II interlaminar fracture toughness of nanosilica modified glass/epoxy fiber-reinforced laminates

Pages 283-290

Hossein Movahhedi Aleni, Gholam Hossein Lighat, Mohammad hossein Pol, Ali Afrouzian

Numerical Investigation of the Effects of Geometrical Parameters of a Viscous Micro-pump on the Flow Rate and Entropy Generation .

Pages 291-302

Hojat Khozeymeh Nezhad, Hamid Niazmand

Prediction of Departure from Nucleate Boiling in a mini Channel Using CFD

Pages 303-312

Ataollah Rabiee, Alireza Atf

A Nonlinear Predictive PID Controller Design for Spacecraft Formation Flying Control

Pages 313-321

Adel Rabie, Maryam Malekzadeh, Majid Abnili

Design and analysis of a novel cable-driven backbone for continuum robots

Pages 322-332

Mahdi Bamdad, Arman Mardani

Comparison between different models of polymer membrane fuel cell using metal foam as a flow distributor

Pages 333-343

Saber Heydari, Ebrahim Afshari

Uniform Star Catalog Generation and Comparison Criterion Introduction for a Typical Star Tracker

Pages 344-352

Jafar Roshanian, Shabnam Yazdani, Masoud Ebrahimi, Mohammad Javad Hasani Kabotarkhani

Direct Numerical Simulation of Controlled Transition Scenarios on a Flat plate

Pages 353-364

Vahid Esfahanian, Ali Akbar Dehghan, Khoshab Masih, Hossain Chizari

Investigation of groove and bump effects on transition region and aerodynamic of a low speed UAV airfoil and wing

Pages 365-376

Alireza Naderi, Mehdi Najafi

Investigating the influence of effective parameters on the residual stresses in circumferentially arc welded thin walled cylinders of aluminum alloy series 5000

Pages 377-386

Vahid Karimnia, Iradj Sattari far

Analytical solution based on higher order shear and normal deformation theory for Buckling of functionally graded plates with piezoelectric layers

Pages 387-397

Morteza Ghasemi, Abdolrahman Jaamialahmadi

Numerical and Experimental Study of splitter blades effect on the centrifugal pump performance

Pages 398-410

Mir Boyouk Ehghaghi, Mohammad Vajdi

Reinforcing Effect of Nanoclay on Buckling Behavior of Nanocomposite Grid Shells: Experimental Investigation

Pages 411-418

Reza Zamani, Gholam Hossein Rahimi, Mohammad Hossein Pol, Mohammad Hedayatian

Fault detection of the 3-PSP parallel robot using the principal components analysis method

Pages 419-430

Amir Rezaei, Alireza Akbarzadeh

Journal Archive

Volume 26 (2026)

Volume 25 (2025)

Volume 24 (2024)

Volume 23 (2023)

Volume 22 (2022)

Volume 21 (2021)

Volume 20 (2020)

Volume 19 (2019)

Volume 18 (2018)

Volume 17 (2017)

Volume 16 (2016)

Volume 15 (2015)

Volume 14 (2014)

Volume 13 (2013)

Volume 12 (2012)

Volume 11 (2011)

Volume 10 (2010)

Volume 9 (2009)

Volume 8 (2008)

Volume 7 (2007)

Volume 6 (2006)

Volume 1 (2001)